r/AutoDetailing • • 7h ago

Check My Work Followed a tutorial on headlight defogging,and now it's worse than when I started. Wet sand, alcohol wipe, clear coat, wax, and then buff.

Thumbnail
gallery
12 Upvotes

Followed "How to Restore Headlights PERMANENTLY" by ChrisFix. https://youtu.be/UEJbKLZ7RmM?is=ga5lxywG3ILqjAlR

Here are the steps I followed, in order:

------

400 grit Wet sand (sand in circular motion and then horizontal)

600 grit wet sand 

2000 grit wet sand 

Alcohol wipe

Tape trash bag over headlights, cut hole 

Alcohol wipe

Apply clear coat (3 coats, 5 min between coats, light horizontal sprays) 

 24h drying time 

 another 2000 grit wet sand

 wax and buff

------

A couple things that may have contributed to my poor results:

- pressed too hard with the 400 grit and scratched the headlight

- didn't have carnuba, so I used Turtle Wax Super Hard Shell Soft Paste Wax (it had a "Depth Carnuba Durability" seal on it)

- sprayed too close on the first spray on the first headlight, saw it start running, panicked, sanded it off immediately with 2000 grit

- waxed, let it get hazy, tried to buff it out anf the haze would not go away so I wet the headlight and used a damp cloth and rewaxed and rebuffed and it was slightly better, but I feel like the wax really just sealed the deal on making my headlights more hazy than I started.

This is my first time doing anything like this so please don't flame me if I made a lot of dumb mistakes, I just want to fix it.

The pictures look better than they do in person. Uneven, splotchy haze.


r/AutoDetailing • • 10h ago

Exterior Wipe marks on ceramic coated vehicle

Post image
7 Upvotes

Hello! I recently ceramic coated my suv (first timer) and now that it’s getting colder and there’s condensation on the cars in the morning, I can see the wipe marks from installation. These are not visible once things are dry. Is this normal? Did I not buff things off enough on install? The car looks perfect in the sunlight when it’s dry, so I was just curious. I used crystal serum light, with one low nap towel to level, and another higher nap towel to buff off the rest. Rag company towels.


r/AutoDetailing • • 15h ago

Exterior Advice on Scratches

Post image
10 Upvotes

Long story short, I bought this truck last week. I came home and found some "scratches" on it after I had left the dealer. When I say scratches, not deep, more like things that can be buffed out. Like finger nail scratches would best explain it. I reached out to the dealer, I was pissed this truck had 5 miles on it! However I don't feel comfortable them detailing it to fix it. Especially after hearing things on here.

Back story I have dabbled diy style in detailing for years. I have all the equipment and products and self learned. However this was all on silver colored vehicles.

My question is what is the best way to tackle these "scratches' on a lighter colored truck like this. (Mudbath tan Toyota) Any tricks, or things to know, products to use or not use. All the insight would help! Thanks!


r/AutoDetailing • • 5h ago

Product/Consumable Favorite protective combos. griots vs P&S

1 Upvotes

Griots 3 in 1 ceramic plus speed shine vs bead maker plus dream maker.
Which one would you choose?


r/AutoDetailing • • 6h ago

Exterior Can I clay over a ceramic coating windshield?

1 Upvotes

So I got my car ceramic coated about a month ago and tonight while driving when the street light hit the windshield I noticed little tiny shiny sparking dots on the front windshield when the light hits it a certain way This car is brand new so I know it’s not damage . I did some research and some people said it’s deep contaminant that won’t come out with regular cleaning. My question is if I can or should use a clay towel for this or anything else.


r/AutoDetailing • • 7h ago

Exterior Weird haze on new car?

Thumbnail
gallery
1 Upvotes

Hey everyone. Just got a certified used 2026 bmw (only 2,000 miles). Got a little dirty from rain so decided to wash today and used meguiars ceramic hybrid wax after. Sprayed on car while it was wet like instructions said and wiped with microfiber cloth. After drying I noticed these odd haze marks or like clear coat marks? Idk I’m not very experienced with verifying paint damage. Only saw on my mirror and toward the front edge above the tire. Was this something I missed before purchasing? It looked shiny and mint in showroom, maybe me washing it revealed something? Or is this a ceramic application issue? The rest of my car is spotless and I used it all over. Hard to capture on camera.


r/AutoDetailing • • 14h ago

Exterior Thick cooked brake dust

Post image
3 Upvotes

Hello! I recently bought a car and one of the wheels has some thick baked on brake dust. I can’t seem to get it to come off hardly. I’ve tried superior products wheel acid, wheely clean and some other wheel cleaners. If I let the acid sit for a little bit and scrub it I get a little bit each time. Is there an easier way, or just keep scrubbing until it’s gone? Thanks!


r/AutoDetailing • • 15h ago

Exterior Which method would be best to wash my car in Apartment setting?

3 Upvotes

So I have a 2004 VW Beetle Convertible and want to wash it. Mind u I barely used to wash it due to leaks in the roof but I want to wash it more often. I live in an apartment where I do have access to a hose spigot but can't hook up a hose or apartment complex would be upset, but I can fill up my bucket as many times as they said. So I am buying a bucket kit that has wash mitt, rinseless sponge, tire brushes, etc. but I've been looking at rinseless wash soaps cuz many say that's the best way to wash the car when in a situation like mine. But I was wondering, could I also get away with doing the 2 bucket method with normal car soap and for "rinsing" to use a small Tupperware to pour water over the soap to "rinse" it off?

So summarized, in an Apartment with no hose situation, should I use the rinseless method or 2 bucket method with normal car soap and pour water to rinse it off?


r/AutoDetailing • • 1d ago

Exterior Husbands car detailed now has swirl marks

Thumbnail
gallery
713 Upvotes

Hi! My husband got his car detailed at the ford dealership where we bought the car. When we got home we noticed in the sun there are swirl marks all over the car. what could’ve caused this and is it fixable?


r/AutoDetailing • • 1d ago

Setup Show-off Rearranged my garage and stopped moving the pressure washer and vacuum around

Post image
17 Upvotes

I changed the layout of my garage and moved the pressure washer and vacuum.
I used to have a portable Greenworks pressure washer and a Kärcher WD 5 wet dry vacuum in different corners. Before washing the car, I had to move the pressure washer to the garage door, connect the hose, and plug it in. After washing the outside, I had to put it away and move the vacuum over to clean the interior.
Both machines worked fine. The problem was setting them up and putting them away every time. If I took a break, I often left the interior for the next day. I had the giraffe wall mounted bundle in my cart for a while. During Black Friday, it was a little over $200 cheaper than the price I had seen before, so I went with it. Both are mounted near the garage door. The pressure washer is close to the water supply, so the hose reaches the driveway. The vacuum is mounted farther inside and reaches the car and workbench.
A friend of mine is also changing his garage setup. He has an Active 2.0 pressure washer and a Prolux wall mounted vacuum. His machines are on opposite sides of the garage. We want to see which layout is easier to use.
Now I take out the floor mats, pull out the vacuum hose, and clean the seats, carpets, and trunk. Then I put the hose back and pull out the pressure washer hose for the body, wheels, and mats. Neither machine has to be moved. The attachments are close by.
The actual wash does not take much less time. I just spend less time moving machines, finding an outlet, and sorting out hoses.
The wet and dry areas are still a problem. Freshly washed mats need to stay away from the vacuum tools and clean towels. The two hoses sometimes cross near the garage door. My friend’s setup may avoid that, but he has to walk across the garage for some attachments.
For anyone using both a pressure washer and a vacuum, do you keep them on the same wall or on opposite sides of the garage? Do you clean the interior first or wash the outside first?


r/AutoDetailing • • 12h ago

Ask Me Anything Did I mess up using the 3m headlight clear coat wipes?

1 Upvotes

Hello, wondering if anyone can give input who has used the 3m headlight clear coat wipes. I used to use ceramic coating but just bought a 40ct of the wipes. This is a customers car and I want to know if the streaks will self level? This is 10 minutes after application. Thanks.


r/AutoDetailing • • 14h ago

Exterior Product to use on top of Fusso Coat? Skip?

1 Upvotes

Hi everyone. I recently purchased the Soft 99 Fusso Coat as a sealant on my car.

I'm wondering if there are some products that would go along well with Fusso Coat as a "base sealant".

I have quite a lot of Koch Chemie S0.02 and Koch Chemie Protector Wax left to use. I'm wondering if using any of those products on the Fusso Coated car would make sense. I was strongly leaning towards using Protector Wax from time to time as it's super easy to use.

Would Protector Wax not last at all when applied on Fusso Coated car?

Let me know your thoughts. I'd love to hear your experiences with applying something over the Fusso Coated car. Thanks!


r/AutoDetailing • • 21h ago

Exterior Tire Shine Sling

3 Upvotes

What’s the way to prevent? I’ve tried a ton of products, have the best success when the car sits overnight, but will still sling a little.


r/AutoDetailing • • 1d ago

Tool/Reusable Early Black Friday Deal

Post image
37 Upvotes

FYI. Home Depot has the Gorilla Ladders 47x12x20 slim fold platform on sale for $49.99, and free delivery. Gonna make roof work on my crosstrek much easier.


r/AutoDetailing • • 17h ago

Tool/Reusable Corrosion on ends of a Nilfisk Core 140 hose

Thumbnail
gallery
1 Upvotes

Hi everyone,

I have a 2.5-year-old Nilfisk Core 140 with the original 8 m hose. Both metal connectors at the ends of the hose are showing signs of corrosion, including on the inside. I've cleaned the connectors, but connecting the hose to the gun is getting increasingly difficult.

After each use, I disconnect the hose from the spray gun, so the connectors should never remain wet for extended periods.

Has anyone experienced the same issue? Is this a common problem with Nilfisk hoses? Is there any way to prevent further corrosion? Or, once the original hose is beyond repair, would it be possible to modify the Core 140 to use a standard, higher-quality hose?

Thanks for any advice!

I have atteched photos of connector before and after cleaning with metal brush.


r/AutoDetailing • • 1d ago

Business Question After reading over 100 posts here.....

26 Upvotes

I believe i may be the only detailer that works at a Car Dealership in the world. What people are doing to your cars are the most horrific "details" i have ever seen and i wish all dealerships would just stop offering car washes all together. I care about everything i do to a car and i honestly don't understand where the disconnect for people is. Has anyone had a good experience at dealerships with details ever?


r/AutoDetailing • • 1d ago

Exterior Help: Windshield Milky Haze After Wipers Pass

25 Upvotes

Can anyone help explain what’s happening and what I can do to fix it? Short clip attached.

Every time the windshield wipers pass, it has this milky haze and disappears after a few seconds if the rain isn’t too bad. When it’s pouring and I have to turn the wipers on high, and it’s nighttime with other cars headlights shining at me, it’s very difficult to see.

Car got coated with a 4 year XPEL Ceramic Coating 2.5 years ago. I installed new wipers last week hoping it would fix it, but no. I tried cleaning it with a clay towel and iron remover, invisible glass spray, and it doesn’t help


r/AutoDetailing • • 1d ago

Interior Interior windshield streaks & “fog” residue?

7 Upvotes

I think I have two separate problems:

  1. I can’t seem to find a way to clean the interior of my windshield without getting streaks. I’ve been using an automotive glass cleaner & microfiber towel (or two) but even with the most care and precision, it’s still streaky. I’ve also tried windex and a couple other cleaners that claim to be “streak free”.
  2. I have this foggy residue that keeps building up. I am meticulously to not touch my glass so it should be from skin oils. When I clean my windshield, it is free of the residue for a short time (i.e. a couple days) but then it slowly starts to accumulate again. It’s been a while so now it looks like I need to run my defogger on my climate controls but I turn them on and if I genuinely needed it, it will help. Even with the defogger running all the time, and all my other glass completely clear, I still have this vague fog on the glass. But if I touch it with my sleeve, I can wipe it away or streak the residue. Then if I try to kinda polish it with a clean cloth, it just distorts lights at night even worse. Help!

r/AutoDetailing • • 1d ago

Exterior Are the black spots artillery fungus? Bought a cheap beater car and want to give it a good clean as best as possible. If so what's the best way to clean

Thumbnail
gallery
8 Upvotes

r/AutoDetailing • • 1d ago

Product/Consumable How do we feel about CG galactic black?

Thumbnail
gallery
3 Upvotes

I am not a detailer. Just a layman who puts a few extra steps toward washing the car. I know this sub doesn't like chemical guys but how about this stuff? Seems to work well enough for me. Anything I should watch out for?


r/AutoDetailing • • 1d ago

Exterior Specks on outside of windshield

Thumbnail
gallery
5 Upvotes

As you can see there are millions of tiny specks all over the outside of the windshield. It’s a brand new car not 3 months old. I had some work done on it and after I got it back noticed them. How can I get them off permanently?


r/AutoDetailing • • 1d ago

Interior Best spot to put ozone generator in car?

3 Upvotes

Which spot is most effective to put an ozone generator in the car?

My sunroof drain was clogged and as a result my front passenger floor and rear passenger floor got wet during heavy rain. I've cleared the drain and removed the water but there is still a wet musty smell that won't go away.

Should I put the ozone generator on the passenger floor or the center armrest?


r/AutoDetailing • • 1d ago

Interior Any tips for removing lingering chlorine dioxide smell from a car?

2 Upvotes

I used a chlorine odor bomb on my Corolla Saturday night. Let it sit overnight for about 12 hours. After letting it vent out for most of that day, there’s still a lingering chlorine smell that doesn’t seem to be dissipating even after 3 days. Any tips?


r/AutoDetailing • • 1d ago

Process Manufacturer difference

3 Upvotes

Hello, I’ve had 10+ new car purchases in the past 5 years for either myself, my kids, or helping my family. My initial detail is always the same pattern, but I’ve noticed a difference in VW paint/clear coat.

I had a 24’ Golf R and now a 26’ Golf R. The paint looks good, but it doesn’t quite leave the “self-rinse” from rain even though I applied the ceramic detail and other prep stages.

Other cars include Durango Hellcat, Mustang DH, Bronco Raptor, Jeep GC, Lincoln Aviator, Audi Q7.

Are each of the other models “better” compared to VW’s quality? Since the Golf R is made in Germany, I wasn’t sure if that had something to do with it. We’ve had two Audis since 2021, and their paint doesn’t seem to be as “sticky” or whatever term I can’t think of to describe the surface as restricting beading.

I use a variety of products including Griots, Chemical Guys, Turtle, etc depending on the state of the paint and what process I am doing.