r/Luthier • • 2h ago

ELECTRIC Baritone neck 28"

51 Upvotes

r/Luthier • • 7h ago

ELECTRIC Dvina clone

Thumbnail
gallery
35 Upvotes

This is my take on Soma Dvina. I made a test version few years ago only to find out that beech wood was a terrible choice so it got warped. This time I took hard maple.
The instrument has an unusual pickup system. The EMF is induced in strings themselves as they oscillate in a magnetic field, similar to a ribbon microphone. Low level low impedance signals is getting converted to a high level high impedance suitable for a guitar amp by the step up transformer. Compared to a guitar magnetic pickup it has much higher signal to noise ratio. The induced voltage is much stronger than one caused by an external AC magnetic field. As a result this system is virtually free of hum.
The main difference from Soma’s one is Halbach magnetic array instead of a single magnet in the generator which gives a bit more focused field.
The body is stained with alcohol stain then Osmo oil stain and finished with Osmo hard wax oil.
The nut (it must be conductive to complete the circuit), tree and contact pads where strings pass through the body are made of nickel silver. Bridge is made of Corian. Compartment cover is a DIY paper plus epoxy Micarta.


r/Luthier • • 5h ago

WES HAUCH CLONE 3D

6 Upvotes

I just clone the wes hauch Ibby in 3d for Cnc!! 27"


r/Luthier • • 48m ago

Can I still use this wood for a neck?

Thumbnail
gallery
2 Upvotes

After routing the truss rod channel and removing all the excess wood, the piece of maple I’m using for a bass neck developed a back bow of about 1/8”. It also shifted by 1/8” off the centre line (as in it used to be straight now it’s a “C” by 1/8”).

I was able to adjust my template and route out the neck shape and the truss rod still goes into the slot with no issue.

All that said, is it okay to use this for a neck and use the truss rod to get rid of the back bow, or should I just cut my losses and start with a new piece?


r/Luthier • • 4h ago

ELECTRIC Bouzouki Pickup in a PAF space: Part II

Post image
1 Upvotes

Posted on here a while back and couldn't find a solution to creating an adapter to attach a bouzouki pickup onto a PAF mount. Thanks to u/Dong_sniff_inc (awful name) for the idea for a 3D printed version.

If anyone is interested in this, I have STL files for left handed and right handed versions.


r/Luthier • • 1d ago

Mandocello Šefl no.01

Thumbnail
gallery
148 Upvotes

Hi, here is first custom-made mandocello from my workshop 😊

Sound sample: https://youtu.be/4ksMCVm0xVc

www.seflstrings.cz


r/Luthier • • 9h ago

REPAIR Novel method for evaluation fret buzz

2 Upvotes

I am an amateur guitarist who recently started setting up and modifying my guitars. I have come up with an electric method of identifying frets which causes buzz using a multimeter. I am considering developing a more suited tool if this could be of any help to luthiers and guitarists.

But before spending time and money on such a hobby project, I would like to know if identifying buzz causing frets is an issue for professionals at all?

Before applying my own method, I have used a fret rocker and straightedge and experienced that fret height and buzz is not necessarily directly related and influenced by setup and string behavior. However, my issues identifying the correct frets might just be my lack of knowledge and skill 😄


r/Luthier • • 8h ago

HELP Can I change my 9.5" radius tele with narrow tall frets to a 12" radius with jumbo frets?

0 Upvotes

r/Luthier • • 18h ago

First Panga neck!

Thumbnail
gallery
5 Upvotes

Picked this up the other day. The neck seems a little sticky and the grain near where it got most of the actions seems a bit more rough.

Any recommendations for care?

Normally I high grit sand necks, I feel that’s not the best idea for this one.

Thanks!


r/Luthier • • 14h ago

Need a little advice

2 Upvotes

Hey guys,

I am finishing up a wiring of a strat HH pickguard, with pickup rings (Seymour Duncan Triple Shot) - with P-Rails.

And I have the rest of the strat wired with push back wire which I like a lot because - my question is do you know if there is something on the PCB of the SD triple shot that would prevent to remove the 2 conductors and solder push back wire in its place. https://www.thomannmusic.com/seymour_duncan_sts1s_t_triple_shot_mounting.htm

​

I would appreciate any advice - the reason is that I not only prefer this wiring but it also allows me to cut the exact length of wire that I need

Edit: Just went ahead with the mod and it works flawlessly - just have to be careful because the bare wire also expects a ground connection. In this case I installed a jumper in between ground and bare sockets on the triple shot PCB.


r/Luthier • • 1d ago

Just finished another Explorer

Thumbnail
gallery
20 Upvotes

So this guitar is the first of three instruments, which i am currently building my band mates in Damage Case. This Explorer was built for the lead vocalist and rhythm guitar player Marco and I can't wait for him to check it out.

I used plane wood for the body which I got for dirt cheap around the corner here in Germany. It had been sitting in some shed for 20+ years, is perfectly dry and it's all one piece. Got it for some 15€. While it looks damn cool I can thell you it was an absolute nightmare to work with, and it is also the reason why this is probably the heaviest Explorer I've ever played, seen, touched, built.

Neck and Fretboard are made from Walnut.

Love to hear your thoughts on it!


r/Luthier • • 13h ago

Help wiring humbuckers

Thumbnail
gallery
1 Upvotes

Sup yall
Been really struggling to know how to rewire my humbuckers , my luthier had them rewired before and then i had them removed and want to rewire long story short where do i start from and what to do
1 tone , 1 volume switch , 3 way pickup switch


r/Luthier • • 1d ago

ACOUSTIC Guitar Leg Rest 2.0

13 Upvotes

r/Luthier • • 19h ago

HELP Wiring Diagram Help

Post image
3 Upvotes

Where does this wire connect?


r/Luthier • • 14h ago

HELP First Guitar: Questions About Pickups and Hardware

1 Upvotes

Hello everyone,

I'm a self-taught beginner woodworker and I've been working with wood for some time now, and I want to take on my first guitar build.

My father doesn't own a guitar with a P90 yet, and he's told me many times that he'd love one to complete his collection. So I'd like to build him a Telecaster-style guitar with P90s, following tchick Guitars' build video.

Is there anything specific I should know about P90s? I'm not very knowledgeable about guitar hardware, so I'm also wondering about compatibility issues between different components. Basically, is there anything I should know before getting into the hardware phase of the build ?

Thank you very much, and have a good day !


r/Luthier • • 1d ago

I used Ronsonol to clean fretboard yesterday…

11 Upvotes

I used Ronsonol to clean an Indian laurel fretboard prior to applying Montypresso. I just found out that Ronsonol no longer contains naphtha(!!!)

Have I made a horrible mistake?

The Montypresso is still on the fretboard, so I haven’t seen if the fretboard is ruined yet.


r/Luthier • • 18h ago

Help!! my guitar is buzzing and i tried everything i could!

0 Upvotes

Brand new Yamaha Pacifica Standard Plus. The low E and A buzz on almost every fret, and you can hear it through the amp. Video: Revstar first, then Pacifica, same attack.

CURRENT SETUP

- Pacifica: relief 0.30–0.35 mm (.012–.014") at the 8th fret, low E action ~2.2 mm (.087") at the 12th fret, 9–46 strings

- Revstar: low E action ~1.8 mm (.071") at the 12th fret, 8s. No buzz.

WHAT I'VE TRIED

- Full restring with fresh strings, neck rested overnight with the truss rod loosened

- Truss rod in both directions: relief from 0.15 to 0.35 mm (.006 to .014"), measured with feeler gauges at several frets

- Action from 1.4 to 2.6 mm (.055 to .102") on the low E

- Saddles reset level, then raised individually on the low E and A

- Frets checked with a rocker and a straightedge: none high

- Tap test on every fret (capo 1st, fretted at last fret): all clear

- Coin tap on every fret: no loose frets

- Fret crowns look round under a flashlight

- Saddles, trem springs and loose hardware checked

- Buzz goes away only when I pick very softly

- My Squier Tele (also 25.5" / 648 mm) at ~2.0 mm (.079") barely buzzes with the same attack

Nothing really changes it. There's no luthier anywhere near where I live, so I'm trying to diagnose this myself. Is this sound normal? What could be causing it?

UPDATE:

Thanks everyone! Answering the most common points:

- Amp: yes, the buzz is audible through the amp, not just unplugged.

- Playing position: it buzzes the same sitting in playing position, not just hanging on the wall. Both guitars were hanging the same way in the video, and only the Pacifica buzzes.

- Nut: measured action at the 12th fret, low E, open vs. with the 1st fret pressed:

- Revstar: 1.8 mm (.071") open, 1.4 mm (.055") fretted at 1. No buzz.

- Pacifica: 2.4 mm (.094") open, 1.9 mm (.075") fretted at 1. Still buzzes.

Both drop about the same, so the nut seems fine. And since it buzzes on fretted notes too, the nut wouldn't explain it anyway.

- Relief: tried from .006" (0.15 mm) to .014" (0.35 mm), letting the neck settle after every 1/8 turn.

So the Pacifica buzzes with 0.5 mm (.020") more clearance than the Revstar. Unlevel frets?


r/Luthier • • 1d ago

Last minute kit project for friend's anniversary.

Thumbnail
gallery
62 Upvotes

Friend's wife wanted a custom guitar to give my friend for their anniversary. But once we talked about time frame and costs a deal was struck since she was also wanting a finish I've never done or been interested in personally.

Told her find kit that hopefully doesn't suck online that looks like something she knew he'd love. Told her to pay at least $150+200. I think she chose well enough.... Told her I'll make it worth a damn to play. And do the finish fretwork and setup for free for their anniversary after practicing on some scrap woods. If he wants any electronics or hardware upgraded he can make that call himself.

Honestly... Aside from battling all the glue bleed through from the kit manufacturer using PVA on a veneer so thin, I'm quite pleased with how it's turning out


r/Luthier • • 20h ago

Bass cut switch?

1 Upvotes

ive also heard this called a strangle switch and ive tried wiring it to a push pull pot following some google images. has anyone found a diagram for this that seems to work well?


r/Luthier • • 1d ago

ELECTRIC Why have three strap pins on a guitar?

Thumbnail
gallery
25 Upvotes

I was looking at some Hagstrom guitars and noticed some models (mostly older models or reissues of them) have three strap pins.

I couldn’t find out a way to word this question to get the search results that answered it so now I’m here

I’ve been playing for most of my life but never really noticed something like this

Why have an extra strap pin on the bottom bout of the body? Especially when neither is centered? Does one have a different purpose to the other?

I’m so confused please help


r/Luthier • • 1d ago

Unsure if I should put bindings on

Thumbnail
gallery
3 Upvotes

just at the stage to try and make sure everything fits. I have not cut binding channels before I am not selling this guitar it is just a gift while I learn and practice the craft.

Do I risk cutting the binding channels and mess it up or do I just finish sanding and cleanup what I have?


r/Luthier • • 21h ago

INFO How to get back into it?

0 Upvotes

Hello everyone. I started building guitars mainly 3 years ago when I took luthiery classes. However nowadays I moved countries and I haven't found any place where I can get back to make the builds I used to do.

What can I do to get back to building without requiring all the big machines and tools a luthier usually has??

What are some resources i can search? I've seen kits and all but they don't convince me yet.

I am open to all recommendations and guidance!


r/Luthier • • 1d ago

ELECTRIC One of my favorite finishes

Thumbnail
gallery
76 Upvotes

r/Luthier • • 23h ago

Parts help

1 Upvotes

My son was given an Iyv Les Paul guitar by someone I work with.

He had gutted it and gave me all the parts to reassemble.

Today I tried to put the humbucker adjustment screws in and they don’t fit.

The humbuckers are Destiny CNC Wound.

The internet says they should accept a #3 machine screw. The screws I have appeared to be 1” #3 but just in case I went out and bought 4 more. They don’t fit either.

Does anyone know what size they might be and where I can find some? My local hardware stores (Home Depot and Ace) don’t have anything smaller than #3.

I considered using self tapping sheet metal screws but can’t find anything smaller than #6.

Any advice would be greatly appreciated.