Finally got around to getting these headers, as well as the y-pipe, installed and boy oh boy was it a motherfucker. This is not a a step by step how-to install, just how *I* managed to get this done and my thoughts on the whole experience.
Ordering Experience
If you've ordered these headers, you know this all started in April of 2026 when orders opened. No small amount of time to say the least and as far as I know, some people have STILL not received their headers. everything came very well packaged in copious amounts of bubble wrap and taped up. The O2 sensor extensions were also not included in my shipment. I emailed with Brockett and apparently this was due to them not getting their harness shipment in time for header shipments to customers. He graciously refunded me $75 to order my own, which I did, but the harnesses should've been shipped by now.
Quality
10/10 Literally no notes here. The piping and welds on both the headers and y-pipe are absolutely immaculate. the flanges are super thick and I have no doubt these headers will last a very long time. See my previous post for some more detailed pics of the headers themselves.
Install Experience and Notes
The passenger side install is not too terrible, although reinstalling the hardware for both side was pretty terrible as the routing for the header piping is much more cumbersome than the stock manifolds. the whole time during the install, I was thinking how much it would suck for you guys in rust prone areas with will inevitably break of some studs. I was able to get all the nuts off the studs and complete the passenger side with the studs still in. The driver's side absolutely sucks. For the driver's side the studs absolutely need to come out. There's simply not enough room between the strut frame mount and the studs to get the headers in. I took the steering shaft out before realizing the studs had to come out, but I think I'd still remove it as it grants you quite a bit more access for install. One thing to note with the studs for you guys in rusty areas what might snap studs, the stud hardware included is too small compared to the stock stuff and WILL NOT thread into the engine block. See Pics. Not sure what happened there. As for getting the dipstick to fit down through the headers, I literally gave up on this and cut the dipstick to a nub, capped it off, and ordered a new one because it was taking so much time trying to find a shape that fit. I'll deal with it later. I address a few things in the post pics, but some other install notes I thought worth mentioning:
-Heat shields are 4-10mm bolts each side, 2 top, 2 bottom
-SAIS tubes are 2-10mm nuts each side
-All exhaust stud nuts are 14mm, studs themselves are E10 Torx sockets. I had to go buy a set
Final Thoughts/Criticisms
The build quality of these are great. The ease of install was pretty bad, but I think that's just the nature of any header install, not necessarily a criticism of these particular headers. The slip on header collectors do not come close to sealing with the headers as the fit is not that tight and the retainer springs are pretty weak. I highly recommend putting a generous bead of Copper Ultra exhaust gasket sealer on each collector pipe. I'm still chasing a few small leaks even after doing this and I may even source some stronger springs to help keep the collectors seated better. For the header/engine block gasket, I ended up ordering an MSL gasket with the valve cover heat shield as the included gasket was just a crush style with no heat shield. With installing the y-pipe with the headers, one thing I'd like to note is there is no hanger between the headers and the stock muffler. This means all the way from the engine block to the muffler, the headers and y-pipe are just supporting themselves. I ended up having to support the driver's side resonator with some wire as it was resting/knocking on the frame. Aside from the small leaks/ticks I'm chasing, the header/resonated y-pipe combo sounds great. It has a great tone under mild acceleration and has just a little bit of drone at highway speeds. I'll try to post some sound soon. The butt dyno definitely feels a power gain from these headers/y-pipe. I've also seen a 2-3 mpg increase more so on my highway commute. The 90 degree O2 sensor spacers I ordered from them for the y-pipe have been working flawlessly and I haven't had a cat engine code once since install.
I hope this will helpful for some of you in deciding to get a set of these headers and installing them. As much of a pain in the ass as the install was and as long as this whole process has been, once I get these small leaks addressed, I think I'll be very satisfied.