r/65Grendel • • Jan 11 '21

The Community is Back Open

135 Upvotes

Our beloved friend /u/pwny_ was the sole moderator of this sub and his account was suspended, which locked out this sub.

I applied for and was granted ownership so it should be open again.

Let me know if someting is off.


r/65Grendel • • May 05 '23

Lilja barrel resolution.

Post image
20 Upvotes

r/65Grendel • • 7h ago

First deer for the Grendel NSFW Spoiler

Post image
33 Upvotes

I built the 16" Grendel back in February, and immediately started reloading for it. It was a toss up to go with loads for the 123 SST using LVR or N540. Both powders have been VERY successful, but the LVR had the tighter groupings. Upon doing the field dressing, the round severed the inferior vena cava and liquified the left lung. The shot was taken from roughly 60yds. I'll be hunting with my 18" tomorrow overlooking a field.


r/65Grendel • • 10h ago

Causes of Failure to eject on AR platform 6.5G

Post image
22 Upvotes

i’m getting consistent failures to eject…. every 3-5 rounds. the rifle is older but has very few rounds through it, under 100-200 probably. i also get more classic stove pipe failures.

can any gurus help me figure out what to tinker with? This is my hog gun i keep at my dads house in FL so it will be a while before i get back to fix it but I would love a list of possible fixes ready for when i go back in Dec.

i’ve read something about this being more common on the 6.5 than 223 builds due to the geometry of the extractor? don’t want to start trying to reshape it without a lot of confirmation that its the problem.


r/65Grendel • • 3d ago

First 6.5 Grendel

Thumbnail gallery
69 Upvotes

I wish I would’ve built this gun sooner for my son.
We have been experimenting with a few different calibers over the years for him to hunt with and think we finally found one that’s gonna be a good fit. He has harvested several deer with a .243 and .350 Legend but I think this little caliber will be the perfect middle ground. Final 5 shot group are the rounds in the bullseye. Sighted in 7 different rifles for deer season between my Dad and I so target was a mess. Was worried barrel wasn’t going to group tightly because of it being new but it settled in very nicely within a box of Hornady Custom 123 gr SST. Ready to put some meat in the freezer.

Build List:
Nemo Arms Battle Light Reciever
Giessele Super Dynamic Combat Trigger
Wilson Combat Recon 16” Barrel
Wilson Combat BCG
Wilson Combat Adjustable Gas Block
Trijicon Accupoint 2.5-10x56 w/ Vortex Mount
Silencerco Hybrid 46 w/ 3 prong ASR Flash hider


r/65Grendel • • 4d ago

Bolt carrier not seating

3 Upvotes

I bought a BCA right side charging 6.5 grendel upper with a 24 inch barrel.

I'm new to the AR platform, and I'm aware of BCA's sometimes shoddy qc. Out of the box, the first shot snapped the extractor, so I know what I'm dealing with. I am enjoying tinkering to the best of my ability. I had several shots while zeroing today that the bcg wouldnt cycle fully. It hit the back of the cartridge and stopped. I just puuled it back and cycled it and everything was fine. No jam, no stuck spent case. Just a little weak. Im using a standard lower parts kit, so Im wondering if there is something about Grendel that needs a stronger buffer spring. What is your experience with this?


r/65Grendel • • 5d ago

AGM Rattler V2 zero coordinates / X and Y values on a 6.5 Grendel setup?

1 Upvotes

Quick question for those of you running an AGM Rattler V2 thermal scope on a 6.5 Grendel setup AR

​When you get your 100-yard zero locked in, where do your final X and Y digital zero coordinates usually end up sitting relative to center (0,0)?


r/65Grendel • • 10d ago

Some Hornady 90gr CX velocities

Thumbnail gallery
16 Upvotes

Scored some 90gr CX for a decent price and finally got some time to gather a rough velocity/accuracy check. The temp and alt was roughly 57f/1500ft.

The howa 20" (match pro 6-24) group was with a suppressor and my first shots of the day. The ar is a noveske 18in barrel (vector 2-12), quite pleased with those groups today as the 70% group is .5moa, and both rifles show promising results. Velocity is pretty good too, even with the 18in the 90gr stays above 2000fps out to 275/300yrds which is probably farther than I'd like to take a shot so up close should provide excellent performance.


r/65Grendel • • 11d ago

Proud to say, this Grendel puts meat in the freezer. 260 yard on a running 160lb six pointer.

Thumbnail gallery
131 Upvotes

16 in Wilson Combat barrel as well as BCG, Dead Air Nomad LTi, Sig Sauer Tango MSR 2-12, Spikes T3, SpringCo white and superlative arms bleed off.

Shooting Hornady Black 123gr I’ve dropped every deer I’ve hit in one shot. This particular shot was taken while the deer was sprinting back to woodline. Cant wait to enjoy the sausages being made at the next two upcoming holidays.


r/65Grendel • • 15d ago

Perun X16 with a 12.5" Grendel Barrel

Thumbnail gallery
31 Upvotes

Build List:

  • Perun X16 Mid length build kit with a modified 10.5" handguard
  • Noveske 12.5 Grendel Barrel with headspaced JP bolt
  • Riflespeed gas block
  • Dead Air Sandman S with a cobalt kinetics keymo muzzle device
  • Modified Aero M4E1 lower
  • Triggertech Tango Competitive two stage trigger
  • B5 MPS stock
  • BCM grip
  • Williams Gunsights buis
  • Primary Arms PlxC 1.5-12 in an ADM recon mount
  • Geissele 20 round magazine
  • Atlas CAL bipod

Just got this scope mounted this past week and was able to make it out to the range just long enough to zero.


r/65Grendel • • 18d ago

6.5 Grendel 2 - AR15 Build

Thumbnail gallery
32 Upvotes

Anderson manufacturing lower receiver
San Tan tactical upper receiver
PSA nickel boron salt bath nitrated BCG
bear creak arsenal - 6.5 Grendel 2 bolt face
MagPul k2 FDE grip
MagPul PRS gen2 buttock
KAK Rifle length buffer tube
Spike Tactical buffer spacer- To run a carbine gas system
Strike industries flat wire buffer spring - for carbine
PSA nickel boron polished stage two trigger
Strike industries locking roll pins
Strike industries - take down pins
No name USA built 18” free floating hand guard FDE
Bear Creek Arsenal 20” stainless steel bull barrel
Vortex AR15 scope mount 20 MOA FDE
Vortex strike Eagle - FFP- 1x8x24 - illuminated red dot
Bear Creek Arsenal rifle length gas tube
Black Rain ordinance - Old School- adjustable gas block
MagPul - FDE- polymer trigger guard
Rearden MFG - FHD - Muzzle Brake

Glad block has been drilled and indexed

Total build price - 2k - built over a couple of years


r/65Grendel • • 18d ago

Howa 6.5 Grendel cut to 14”

Post image
63 Upvotes

I like hunting with shorter rifles, so I cut my 20 incher to 14 inches for this season. Got an Athlon 2-12x on it (want to get a Leupold 2-10 or 2-8 though). And rocking a rugged razor 556 because it’s my only can that has baffles big enough to fit the Grendel. Shoots ELDM better than SST’s so I may be hunting with them. Was able to hit a 12x12 plate at 600 yards 1st try with ~5 mils drop. Over all super happy and look forward to see how a deer takes a 123 gr vs last season 6 arc shot


r/65Grendel • • 19d ago

Wife got her first big game animal with the 6.5 Grendel at 260yds.

Thumbnail gallery
125 Upvotes

My wife test fired about 8 rifles, and different caliber. From 6.5x55 Swede, to 7-08, to .257 Roberts 6.5 Creed, 7x57 mauser. She felt the most comfortable on the 6.5 Grendel Howa Mini Action. So I put a Swaro Z5 4-12 on it, and a purple Boyd Stock. We spent a few weekends at the range putting her in different shooting positions, and ranges.

We shot at the range to 200yds, but never went past that. Her groups at 100 were sub moa on the bench. Close to sub on sticks. The gun was sub moa at 200, but she wasnt.

We ranged the deer at 390yds downhill along a tree-line and knew it was big bodied but small antlers. I asked her "Does he at least have 2 each side?" She said "I think so, but its my first buck and I'm not trophy hunting." She slowly made her way down the hill and we couldnt get any closer than 250 yards.

She put her tripod up, and as soon as I got the deer in my binoculars I hear BOOM. He ran 10 yards into the tree line.

Proud of my wife, and love the rifle. Love the caliber.


r/65Grendel • • 19d ago

Robinson Armament XCR-L in 6.5 Grendel with 1-10 LPVO and Buck Antelope

Thumbnail gallery
53 Upvotes

I shot this buck antelope last Saturday from about 300 yards. It went right down. The XCR is truly an all All Purpose Weapon (APW). They can be used for self defense, hunting, target shooting, and LE and MIL work with the ability to change barrel length and caliber quickly.


r/65Grendel • • 19d ago

Can this be salvaged?

Thumbnail gallery
11 Upvotes

Very long story short, my 16” 6.5G fell 42” on to the concrete floor from the bench at our outdoor range without the thread protector on, and hit barrel first.

Stupidly aside, it appears that the crown is intact, so is it possible to try to rethread it?

__________________

EDIT: I was trying to be brief in my original post, but it appears folks are wondering why I didn't have a muzzle device on the end of the barrel -- I had just removed the thread protector after removing it from my travel bag and positioned it on the table standing it upright w my adjustable Harris (S-BRM-MLOK) bipod.

I did NOT check the tightness of the swivel/tilt and as bad luck would have it, the bipod quickly tilted to the left and of course, I was on the right side of the bench retrieving my Omega 36M and could not grab it before the 12 1/2 lb rifle fell off the table and hit the concrete.

__________________

Thanks!


r/65Grendel • • 19d ago

Stuck crush washer. Best way to remove?

Post image
11 Upvotes

I’ve cut them off with a dremmel in the past. But wondering if anyone else has a better idea.


r/65Grendel • • 23d ago

Does criterion still stock grendel barrels and if not?

5 Upvotes

Someone told me last time criterion stocked grendel barrels was 2 years ago. idk if this is true however if it is what are some comparable options in terms of price and performance?


r/65Grendel • • 25d ago

Ppu 120gr BTHP projectiles

2 Upvotes

Anyone load the PPU 120gr BTHP projectiles with decent success? They're so cheap it's hard to not pass it up and try them out. My howa mini likes a steady diet of 123gr lapua scenars and xbr. I can get 200 of these ppu for the price of 1 box of lapuas. I'm Shooting steel out to 800yrds.

I Don't care about the factory loads.


r/65Grendel • • 27d ago

Budget Grendel build and my first AR

Thumbnail gallery
41 Upvotes

My original idea was to build a 12 inch Grendel pistol for hunting big game and coyotes and learned after I had almost every part that you can only hunt big game in Colorado with a 16 inch barrel. So dumb on my part! I went budget on almost everything except where you touch things. I started with a blem stripped lower from PSA. I really liked the idea of right side charging, so I went with a Bear Creek Arsenal upper receiver. The PSA Guardsman lower parts kit got me started down the Magpul path. When I have to pivot from to a 16 inch barrel, I replaced the pistol brace with a Magpul DT Carbine Stock and angled fore grip. Everything else is pretty budget. Montrum scope and handguard. BCA Grendel barrel. I did spend some money for an adjustable gas block from Strike Industries. I figured I could dial in the gas better with that.

So, I was left with a 12 inch PSA barrel, 12 inch Monstrum handguard, and HAR-15 pistol brace with Dirty J Designs Devoid plug add on. It killed me to not be able to make the pistol I wanted but I am happy with the results that I got.

What do you guys do with parts that you have leftover? And who has the most parts leftover from a build? I can't be the only one who bought the wrong thing. Right?!?!?!?

Thanks for taking a look. Let me know if I messed something up or have other questions.

Rene


r/65Grendel • • Oct 19 '26

My Grendel got the job done. First ever hunt, first time reaching out past 150yards.

Thumbnail gallery
117 Upvotes

r/65Grendel • • Oct 18 '26

Some Grendel groups and velocities

Thumbnail gallery
15 Upvotes

*All groups at 100yrds and different days too, most are from my reloads (marked R)

First photo is a 10x group through my 14.5 with s&b fmj

-shooting with a 4x juliet mag I think this an okay group for my gpr build and some basic fmj.

Second photo is through my Howa mini 20, top groups are 10x and the bottom group is a 20x (also suppressed)

-An okay set of groups and I know my shooting wasnt too good that day. The 130gr otm group is real promising to me cause the rifle was hot, the can was hot, I was running out of sunlight dealing with mirage so all that and still consistent enough is a good sign to me

Third photo is groups from my ar with an noveske 18

-Not so great groups, have shot better but my range days are inconsistent and spaced out a lot so no surprise im shooting poorly.

Hopefully reddit doesnt nuke the quality too bad


r/65Grendel • • Oct 15 '26

Rexus SBR + ELD-VT

Thumbnail gallery
28 Upvotes

Purchased the Rexus 12 inch barrel for lugging around fields hunting hogs. Still less than 200 rounds through it but it seems to really like the Hornady 100gr ELD-VTs

Just purchased a sandman x and was re-zeroing with the new can. 100yd groups after a few 50 yard "get on paper" shots:


r/65Grendel • • Oct 14 '26

MidSouth has 100ct. Nosler Brass + 500ct. 123gr Match Bullets for $150 + free shipping right now

Thumbnail midsouthshooterssupply.com
33 Upvotes

r/65Grendel • • Oct 11 '26

Any idea when criterion might bring back their 6.5 Grendel barrels?

6 Upvotes

I tried contacting them and also asked midway, but no dice. Anyone happen to remember the last time they even stocked them?

Been waiting for one for a while. Starting to lose hope since I’ve missed some good clearance barrels in the last 2 years. I love my Grendel for hogs. I see x-caliber can push out a barrel but wait time 11-18weeks right now and I can’t justify the 500$+ price tag of pf barrels for my hog gun.


r/65Grendel • • Oct 07 '26

Grendel ar bolt parts compatibility

7 Upvotes

Ejector claw on my bca 6.5 Grendel ar upper broke yesterday, rather than get another bca part, how compatible are these ? Should any aftermarket ejector claw work with any bolt?