r/AUG • u/Ohh_Yeah • 2h ago
r/AUG • • Dec 21 '25
Oops Safety Announcement: Do not use the SSAUGv2 with the Heresy 9mm BCG
A tester noticed using the SSAUGv2 with the Heresy had bad timing and resulted it premature detonation. Nobody was hurt and nothing was damaged, but nonetheless the SSAUGv2 trip is designed around the OEM BCG. Please wait till we make one specific for the Heresy 9mm.
r/AUG • u/the__grim__sleeper • Dec 04 '25
PSA: Using A3M1 Rails/Optics on A3M2–QD Optic Adapter
galleryIn case you didn’t know, it is possible to run A3M1 style rails and optics on an A3M2 receiver without leaving an ugly gap or losing the forward QD sling mount that the AUG is known for. However, the part(s) necessary for this aren’t sold on Steyr’s website. You will need to email or call Steyr and ask for parts US1264020040 ($58.27), 3900073 ($3.50), 3860019H ($1.00). Those are the M2 QD sling swivel, screw, and roll pin, respectively. The QD sling mount is rotation limited. Also works with Clawgear handguard.
r/AUG • u/Accomplished-Meat525 • 1h ago
News New HUB mounted Modular Reflex System for the AUG!
galleryHi All!
I've been sitting on this design idea for some time. But now, it's with much pleasure I introduce the first and only (Patent pending) Modular Reflex system for the AUG rifle.
The meat and potatoes and what it achieves;
This is a three piece Modular Reflex System (MRS) that allows you to attach any HUB capable suppressor, silencer, blast diverter or linier compensator to your host rifle without the use of a proprietary muzzle device.
The rear of the modular reflex system (MRS) uses the bayonet lug threads to attach to the rifle barrel. This seals the system and allows the internal volume of the suppressors blast chamber to be essentially doubled.
The middle section is, as the name implies modular. When removed, the attached muzzle device is allowed to telescope over the barrel, allowing the muzzle to protrude into the suppressor.
This allows for different length configurations and a choice of the rifles overall length and suppressor efficiency. Additional length middle sections (eg. 1/2") would be available for custom desired configurations. (shown in the phots is the 1" or 25.4mm middle section)
The front section of the MRS uses a ported bypass collar to hold the device in place around the barrel, while still allowing the end user to add a muzzle device like a brake. (The muzzle threads are NOT used to secure the MRS) This gives the device a second point of contact to ensure proper alignment during mounting and shooting, while also allowing gas to enter the expansion chamber. This front section also has the HUB threads that interface directly with the suppressor/muzzle device.
What all this means for the end user;
If you have a HUB mounted muzzle device/suppressor, you can now make that item a reflex design! Since the addition of extra internal volume helps a suppressor efficiency, you will now experience lower back pressure and better suppressor performance.
With this same design, you may also remove the middle section of the MRS and essentially replicate a K can, but while keeping the benefits of the added volume of a reflex design.
This system gives both the benefits of reflex suppressor and the ability to choose the overall length of your platform.
Summary;
Before this option, you had to pick either a reflex suppressor, a K can or a device such as the OCL OPS/AE/OC HUB Reflex Adapter.
However, with the OCL/B&T design you are still limited to one length and the need for a proprietary muzzle device for mounting.
This ultimately results in diminishing returns, as internal volume is now decreased using an additional threaded and collared muzzle device.
With the MRS, you achieve all the benefits, without those mentioned drawbacks.
r/AUG • u/im09monaco • 8h ago
Finally
galleryA3M2 arrived this Monday and Corvus rails and other stuff next day.
Gotta find some mags soon.
r/AUG • u/Unable_Divide_6664 • 2h ago
M1 rail on a M2?
Accidentally got the Corvus M1 rail with the ACOG direct mount and came to realize something looked off. Well, it was made to fit with the front swivel which the M2 doesn’t have. Was wondering if there is an aftermarket swivel to close the gap or if I should just try selling it.
r/AUG • u/Bahaadur73 • 1d ago
Gear & Kit How come we still don't have companies making the AUG A3 CQC Rail kit in times of 3D printing etc.?
r/AUG • u/lemons4sail • 2d ago
Question Awful horrendous downright evil Steyr customer service
Guyz pls help I just traded my entire Funko pop collection for an MSAR STG 556 and when I looked at the pic rail there was a scuff mark on the metal. UNACCEPTABLE!!! I contacted steyr directly and after an entire 8 hours of waiting they told me that they can't warranty this rifle because they don't make them anymore. How can I sue Steyr generally and Herbert specifically for one gorillion dollars?!
r/AUG • u/Spam_Goose_XIX • 1d ago
Where to get deals on an AUG?
I've been wanted one ever since I was a kid and decided now is a good time to try to get one, any recommendations on where to get one for a good deal online? I dont mind between M1 or M2 I'd just rather not pay full retail on an M2, cant get one local because nobody stocks them, eventually would like to get HBAR barrel as well
r/AUG • u/vagusbaby • 2d ago
Question Aug A3 SF 60mm tube fits in A1 housing
Hello all! I have an A1 with the classic 1.5x donut optic, and looking to replace it with the A3 SF 60mm 3x tube. To be clear, I am thinking of removing the actual optic tube from the A3 mount and replacing just the A1 optic tube, as I know that the A1 optic is integral to the receiver. I've seen a YT video by someone who has done this, and wondering if the A3 SF 60mm will fit. I appreciate any other info y'all have to share!
https://www.youtube.com/watch?v=2VIrc9nnduI&list=WL&index=1&t=196s
r/AUG • u/PeakViewRange • 3d ago
Photo Update: we got the line throwing dildo 😂😂😂 enjoy this Australia masterpiece
r/AUG • u/elvincino • 3d ago
Question New NATO AUG owner question
Hello,
I recently purchased an AUG and was reviewing my rifle for some of the issues I’ve seen crop up for people. The only one I may have is if I try loading a mag while the bolt is back and hit the bolt release it will snag on the mag if I’m pushing up on it, but will free itself when pulled down and seem to load normally. Only tested this on a lancer mag so far. Curious if this is cause for concern or fixable. Referencing this video, the “magazine catch malfunctions” section.
r/AUG • u/InternationalBar8554 • 2d ago
Photo Steyrs only customer service rep be like
steyr customer service is trash and herbert should learn proper english
r/AUG • u/NewbRedditer • 3d ago
A3M2 Issues
galleryI have had a covid a3m1 since roughly 2021, and honestly never had an issue. Probably only 1k rounds through it as i dont have a good spot for rifle shooting, but it has been a good gun. I purchased it in FDE, and wanted the ODG for my environment instead, and so i had hoped to "upgrade" to the a3m2 in green.
Finally picked one up a month ago, and im curious how peoples complaints have been resolved. I have never been able to get ahold of steyr usa (only steyr europe) to answer questions over the years. Right off that bat, the gun had a lip (appears intentionally machined in) in the charging handle slot that was binding / catching and locking the bolt back (pictured with red arrow pointing to it) this has stopped after racking it about 100 times, now it just catches a little instead. The a3m1 charging handle slides much smoother even after break in compared to the m2. The stock carving / deburring looks notably worse than the a1, but maybe acceptable or due to the darker color? The only benefit to the A3m1 (for waffle mag guns) i hear is the better rail compatability but i can find more m1 rails than m2s, the charging handle on the m1 was never my favorite but somehow the m2 is worse imo. Someone last week also complained about little bubbles in the buttpad, and upon inspection mine has them as well.
My big issue is the top picatinny rail. Maybe im retarded but im unable to find any aftermarket options currently, and the factory one is bad. By bad, i mean, the spec for picatinny 1913 rail is .835" (+/- .002) for the rail width, and the rail is .832 at the front, .817 in the middle , and .831 in the rear. Whats odd is that if i take a QD scope mount or bipod (midwest industries mount, and accutac bipod, aka good brands) and set it to a good rail (a3m1, magpul mlok -> 1913 rail, and a few other guns) the QD is able to be set and work interchangeably (or extremely close) between all of them. The bipod / scope mount will clamp right onto whatever gun i want and be snug without adjusting. But with the a3m2, even the rail sections that are the correct width (the very front of the rail), it is no where near snug, infact it is so loose it rattles. So the rail is off in MULTIPLE dimensions, and its not even consistant as you measure along the rail. The QD mounts were almost loose enough to remove them from the rail when clamped down in the middle section. Not so much a knock as a oddity i noticed, but the cast piece that connects the barrel, gas block, and handle also appears to be a rougher casting finish, and a wet look to the glossy finish (and no its not just oily). Ive included a pic of the m1 to show a comparison.
Im not sure if steyr will fix this is the thing, and i know they are nearly impossible to get ahold of. Is it worth the effort? My concern is that people have been reporting out of spec rails for a long time, and its not been fixed. It just seems ever since steyr got new ownership in 2024, the QC is terrible. Do they still stand by there products?
r/AUG • u/dirt_operator • 5d ago
Question Finally was able to join the waffle gang. Need help deciding an optic setup.
Picked up the red spring kit with the rifle and a KNS discarder months ago in preparation for getting the rifle to shoot suppressed. I love the original look of the Aug so I’d like to get either an original style optic or get the manticore talon mount however I’m not sure about sacrificing the rail. For those with either setup, what do you like or dislike about it to sway me one way or the other?
I appreciate the help and if yall have any other suggestions I’d appreciate them as well.
r/AUG • u/Thatguy1142 • 5d ago
Homemade Suppressor Plug Update
Recap: I drilled the normal setting on my 20" barrel's gas plug out to 3/32 in preparation for a suppressor.
After taking out and testing with a Griffin Armament Dual Lok 5 the rifle is still working great though unsuppressed my ejection pattern tends to kick brass about 4-5 o'clock and suppressed it reliably kicks brass at 3 o'clock
r/AUG • u/PurpD420 • 5d ago
Photo Pair of quiet Austrian girls
Been a hot minute since I’ve been able to take my Augs out to play
r/AUG • u/Professional_Realist • 5d ago
ARID USA
Yall's website ever coming back online or what? Hard to make any money when people can't access your site for 2 weeks.
r/AUG • u/CowSniff • 6d ago
PSR-5 on the AUG
Not fully done yet!
Arid trigger and deflector
Meridian Arms CH
Will post completed build
r/AUG • u/Kingpin17 • 6d ago
Optic screws backed out during firing, now I can’t remove my barrel.
Title says most. I purchased an AUG A3 M1 with no optic and then replaced the empty rail with the integrated 1.5x scope from Steyr. The problem is that I didn’t use enough loctite when putting the screws back, and after a range trip they have back out enough to where they are preventing me from removing the barrel. Does anyone have any tips on how to access the screws or remove the barrel?
r/AUG • u/Vladabeast • 7d ago
Red Springs
Just want to see if this is what everyone's springs looked like?
Should I take off all the loose bits first?