r/AnalogRepair • • 2h ago

Just did my first full lens service

Thumbnail
gallery
25 Upvotes

Its aperture was super oily and didnt close fully. First time disassembling a lens this far (only did helicoid regreases so far), but she cleaned up nicely and working tacky and quick again now :)

This is a Carenar 28mm 2.8 m42 lens


r/AnalogRepair • • 6h ago

Camera body Rubber grip coming off on Bessa R3M

Thumbnail
gallery
4 Upvotes

What's the best way to glue this back on? It's a different material than the leatherette, (it's more of a rubber), is there a specific adhesive I should use? should I pull it off completely, remove the dried glue? Is there anything I should know about how to do this without getting glue all over my camera? Is this best left to a repair shop?

Thanks in advance for the help!

EDIT: I'm considering using 3M 468MP transfer adhesive, anyone have insight on using this stuff?


r/AnalogRepair • • 2h ago

Nikon 35TI, how to open the lens compartment?

Post image
2 Upvotes

I have seen people open the front lens compartment of the Nikon. Mine has a misplaced shutter leaf, that I want to reseat. Before I try some random prying, is there anyone who can tell me how to remove the front.


r/AnalogRepair • • 6h ago

Redoing gaskets on an Olympus XA2

2 Upvotes

I recently found my dads old camera (An Olympus XA2) and i would like to start using it. I took it to a shop to see if it was still working and there I was told that i would have to shoot a roll to see if everything was ok but they could already tell that the gaskets would need to be redone

I shot a roll of Kodak ColorPlus200 and everything else seems to be in order and i was wondering if redoing the gaskets is necessary or if it would give noticeably better results since money is a little tight.

The only thing that seems wrong a purple hue but i can't tell if anything else is wrong or if its supposed to be different

Here are some photos i took with the roll of ColorPlus i took(on drive because the files were too heavy)

https://drive.google.com/drive/folders/1b6I1DvMvjeePAxybymD6w-pgTrFlwcqg


r/AnalogRepair • • 10h ago

Camera body How to install Nikon FM shutter strings?

Post image
3 Upvotes

This is getting frustating, I couldn't route the string properly to the cam and get it tensioned... Anyone did this before?

EDIT: Also having trouble of the shutter sometimes fires on its own after winding... I just finished reinstalling the blades, any help is appreciated!


r/AnalogRepair • • 6h ago

Need Advice for a used Lomo lc-a

Thumbnail gallery
1 Upvotes

r/AnalogRepair • • 16h ago

Camera body Need Help with Olympus Pen D

Thumbnail
gallery
4 Upvotes

I hope I could get some help.

I bought an Olympus Pen D last year and I was able to use almost a full roll with it and parked it with the film inside while waiting for an event to use up all the film.

6 months later, the rewind lever would not work. I assumed the film was exhausted so I removed the film. Rewind wheel still would not work. So does the shutter button. (I'm assuming because it is not rewound). I removed the top cover to check if there is a jam but I didn't find anything. Sharing some pictures I took of the camera.

(Last picture: this button pushes in and springs out which is normal)

I really hope someone could help out.

Thank you.


r/AnalogRepair • • 14h ago

Camera body Broken Yashica T4 Super Weatherproof Film Door

Thumbnail reddit.com
1 Upvotes

r/AnalogRepair • • 18h ago

Camera body Anyone still diving with a film camera?

2 Upvotes

Hey everyone!

I recently bought a fully working Sea & Sea Motormarine II EX, and I'm planning to use it for scuba diving at around 18 meters.

The camera is over 30 years old, so I'm a bit concerned about the O-rings. The manual only mentions maintaining three of them (battery compartment, back cover, and external flash connector), but what about the internal seals around the shutter speed and other control dials?

I actually have another unit that suffered water damage, possibly through one of those controls.

Has anyone used one of these cameras for diving recently? Did you replace or service all the internal O-rings, or just maintain the three mentioned in the manual?

I'd love to hear your experiences before risking another flooded camera. Thanks!


r/AnalogRepair • • 1d ago

DIY Project Witness Mini - 3 diode shutter tester

Thumbnail gallery
7 Upvotes

r/AnalogRepair • • 1d ago

Camera body Kiev 4 / Contax iii lightmeter

Post image
2 Upvotes

r/AnalogRepair • • 1d ago

Camera body Need help for my Calloflex type 1

5 Upvotes

Hi everyone,
I’m currently trying to fix a 1950s Caloflex Type I TLR (made by Kowa/Kofuku Sangyo), which uses a Seikosha-Rapid leaf shutter.

Here is what’s happening (see video attached):
Puce Film advance / cocking: The winding crank spins endlessly without ever stopping or cocking the shutter.

Puce Shutter release: Pressing the shutter button does nothing

Puce Manual check: With the front faceplate removed, I can manually move the blades/lever with a toothpick and they open and close freely without being gummed up, so the blades themselves aren't seized.
I'm having trouble tracing where the linkage between the winding mechanism, the shutter cocking ring, and the release bar is disconnected or out of sync.
Has anyone worked on a Caloflex or a similar 1950s Japanese crank-wind TLR with a Seikosha-Rapid? Any pointers on what to check next (wind-side gearing vs. shutter cocking ring/spring) would be hugely appreciated!


r/AnalogRepair • • 21h ago

Bronica S2A Prism finder

Post image
1 Upvotes

r/AnalogRepair • • 23h ago

Minox 35 ML shutter speed issue

Thumbnail reddit.com
1 Upvotes

r/AnalogRepair • • 1d ago

Camera body Canon A-1 problem with power/shutter? need advice

1 Upvotes

hello! just got new batteries for my canon a-1 but when i press the shutter button the led light for the battery check just flickers and the shutter doesn't go off either. and the led for the meter in the viewfinder only appears for like a nanosecond when i lift my finger off the shutter button so i figured this could be a power issue? and i'm guessing the shutter doesn't go off because the camera is off anyways? is this still fixable?

i havent used this camera for a while (last used back in january this year) because ive been so busy and i only shoot occasionally since film is so expensive these days. kinda sad that the camera has this issue now because i was thinking of bringing it for an upcoming trip then selling it after since i always reach for my srt 101 anyway. very much a noob and very far from an expert so i would appreciate all the help i can get! thank you!


r/AnalogRepair • • 1d ago

Minolta X-700 Troubleshooting

1 Upvotes

r/AnalogRepair • • 1d ago

Fuji gs645 shutter repair

Post image
5 Upvotes

Hello, I have a Fuji gs 645 that I’ve changed the bellow on it. When the shutter is out of the camera it arms and fire correctly but when I put it back in its position it goes into T mode when I wind the camera. I’m quite confused about this problem and I’m not certain de repair manual answer my question. Any advice?


r/AnalogRepair • • 2d ago

Charge issue on the RZ67 Pro bodies

Post image
24 Upvotes

A while ago there was a post about finding a magic solution to repair the charge issues on RZ67 Pro/Pro II bodies. That issue has been discussed on Bill Rogers' IG page numerous times, where Bill mentions all the parts that need to be replaced for the camera to run within factory specs again. Once those parts are replaced, everything needs to be recalibrated again using factory tooling (cocking angle, etc) There is no single part that will magically solve the issue. It requires an extensive disassembly of the camera and replacement of numerous parts and/or adjustment of existing parts in order to get the camera body working again.

The Mamiya repair community was accused of being averse to repairs, because lo and behold there must be a quick and easy solution which is being hidden from the general public. I will gladly post a photo of the easy and fast solution in order to repair that issue. It can take up to 8 hours to get all of it working properly depending on how badly the mechanism is worn. And believe me most of them are badly worn once they've reached that point (another reason not to buy a cheap worn/abused body). The times where you could order everything from Mamiya and just replace all, are long gone. It would make the repair faster but I highly doubt it would make it cheaper. Parts cost money. Time costs money. And no, these parts can't be 3D printed without machining work involved in post.

Quick fixes are quite rare in camera and lens repairs. You either do it right or don't do it all because in the end, you want a reliable camera to work with. You don't want a camera which will eventually fail again after a few weeks/months of use.


r/AnalogRepair • • 2d ago

Rolleiflex 6006 shutter stuck below 1/30

Post image
6 Upvotes

Hi All,

I got a Rolleiflex 6006 that doesnt fire below 1/30

What I checked:

Battery is original and charged with the original charger

The problem is still there when using a lens, I have tested it both with a 80mm f2.8 and 250mm f5.6

All times (including Bulb) below 1/30 fire (inclusing the lens) but the mirror doesnt go down again as can be seen in the picture.

When turning the shutter-timing knob to 1/60 or above the mirror resets again to the normal position. I donnot know if the shuttertimings from 1/500 to 1/60 are accurate, they might all be the same....

Is there anyone that knows what the problem could be? There is not a lot of information online about this type of camera.

All help is welcome, thanks in advance!


r/AnalogRepair • • 1d ago

How do I fix this?

Post image
0 Upvotes

Bought it a few days ago, didn't see that defect on the self timer. Tried to push it back in place but it's stuck. How can I fix this?


r/AnalogRepair • • 1d ago

Lens Canon AE-1 Program Accident: Should I Get It Repaired?

Thumbnail
gallery
2 Upvotes

My Canon AE-1 Program had an unfortunate accident. It was dropped, and a piece of the front chipped off. The film inside also broke off, but other than that, the camera seems to be in working condition.

Since this is my first analog camera, I'm still learning my way around film photography and camera maintenance. I'm wondering if this is something I should get repaired sooner rather than later, or if I can hold off for now since it seems to be more of a cosmetic issue and doesn't appear to affect the camera's functionality or photos.

Has anyone experienced something similar with their AE-1 or another film camera? I'd really appreciate any advice or insight!


r/AnalogRepair • • 2d ago

Lens Help needed with reassembling Prontor-SVS Shutter

Post image
4 Upvotes

Hi all. A couple of months ago I bought a Polaroid 110A camera with a Rodenstock-Ysarex 127mm 4.7 lens. This lens comes with a Prontor-SVS Shutter. My aim was to convert the camera to shoot Instax. Anyway when I got the camera I knew there was issues with the lens, and it required a strip down as there was gunk on the shutters and aperture blades that I just could not get clean. I have done some small CLAs, but wanted to do a full restore in this lens. I took photos of every step of the disassembly process for when it came to reassembly. This was about 2 months ago. So over the weekend I actually had some time to clean all the parts and start the reassembly process. I went to get the photos off my camera and the bloody card is corrupted. I tried everything to get them off but everything failed. So next step was to find some of the exposed diagram views to help with reassembly of the aperture and shutter blades. The manual I already had did not have any useful diagrams of the shutters and aperture so I spent most of yesterday looking with no luck. Anything I do find is slightly different to my shutter, and therefore all the insides are slightly different.

My question is has anyone on here done a full strip down of this exact shutter, and if so do you have pictures or notes on it? I have attached a picture of the lens when I bought it and took it on my phone rather than my digital camera.

Thanks in advance.


r/AnalogRepair • • 2d ago

Camera body Sticky shutter button Yashica A

Thumbnail
gallery
6 Upvotes

I thrifted a Yashica A that's unreasonably good condition I've put a roll through already and the shots came out great.

My one issue is that the shutter release seems to stick at the bottom of its travel and it's very inconsistent to tell when and where in the press things will go off. I suspect it some grease that has been sitting there for twice my lifespan and then some but I can't find any manuals on the best way to go about opening the A model. My intrusive thought is to just put a drop of lighter fluid down the channel of the button but I'm afraid that would do more harm than good. I was hoping that people here might have some guidance or resources.


r/AnalogRepair • • 2d ago

Camera body Nikon F100 repair uk

Thumbnail reddit.com
1 Upvotes