r/BeginnerWoodWorking • • Jan 27 '26

MOD POST: NO AI IMAGES, PLANS, ETC -

325 Upvotes

I can't believe I have to make this type of post.

This is not a place for AI Images, AI Plans, responses, etc.

AI Images: AI Images give false impressions of work. If you are posting AI Images and trying to pass it off as your own work. You will be banned under Rule 3 - Original Content and Rule 7: No Karma Whoring

AI Plans: While AI is good at something, you should never TRUST AI to properly create woodworking plans. There are MANY TRUSTED Sites that have free or low cost woodworking plans. Posting of AI Plans will get your post/comment removed, and a possible ban. Under Rule 3, and 9.

Thank you for your attention to this matter!


r/BeginnerWoodWorking • • Mar 31 '26

STOP POSTING YOUR "VIBE" CODING APPS HERE!!!

417 Upvotes

If you post, they will be removed! Full Stop! No discussion! If you keep trying to post, you will be banned! Read the Rules of the sub you are posting to!

We don't want your AI SLOP/Vibe Coded app. You aren't the first person to create that type of app.


r/BeginnerWoodWorking • • 1h ago

Finished Project Beginner Brutalist Wood Coffee Table

Thumbnail
gallery
• Upvotes

Hey everyone! Recently got into woodworking and furniture making and took a crack at a new coffee table. Made out of 4x4 posts, a couple of 2x12 planks glued and pocket jig scrhe sanded down screwed together, then carved using an angle grinder, then 3 coats of stain&poly on the table top and bottom shelf. Then I put some regular poly on the base itself just to protect it moving forward. On the bottom, I have some regular furniture gliders and plan on making some concrete blocks for the base to fit into for some more horizontal support!

Currently working on a new concrete base and wood arch lamp, then a bed frame, then a new couch haha, super excited to be here! Hope you all like!


r/BeginnerWoodWorking • • 18h ago

Working at it since Covid

Thumbnail
gallery
587 Upvotes

Have made some fun things, but at a roadblock. Lost interest, have new tools sitting idle. How to get motivated again?


r/BeginnerWoodWorking • • 13h ago

Finished Project Birdhouse I built had a visitor today

Post image
176 Upvotes

I built a birdhouse earlier from scraps and bark leftovers from live edge wood. I made the hole 32mm to attract birds like great tit and today I saw them checking it out! This makes me very happy :D :D

It has proper roof, the bark is only on top of the roof to act as rain barrier and camo.


r/BeginnerWoodWorking • • 20h ago

A little bit of mineral spirits and tung oil did aaaaalllll the work today.

Thumbnail
gallery
419 Upvotes

I’ve been wanting to clean this poor thing up for a while but I’ve been nervous about messing with it at all since it’s so old and pretty sentimental. I had a piano tuner and restorer look at it today and he gave me an enthusiastic green light on a light sanding, rubbing it down with mineral spirits, and generous amounts of tung oil.

I hardly did any work on it. I basically just gave it lotion. It could use a little more sanding but I’m happy with this for now. Low effort, high payoff. That’s rare with most projects so I figured I’d share it here.

It’s a 1915 Packard if anyone wanted to know. Piano guy said he rarely sees ones like this in such good condition. He got it sounding really nice.


r/BeginnerWoodWorking • • 6h ago

Discussion/Question ⁉️ Is it good enough?

Thumbnail
gallery
31 Upvotes

Ive never done an ounce of woodworking before this.

This is a stand for a 125 gallon aquarium. The tank will be approximately 1300 lbs. once fully set up. I didn't trust the stand it came with at all, so I decided to reinforce it, even though I had no experience and only had a drill and hand saw to work with. Do y'all think this will sturdy the stand up enough? Thanks!


r/BeginnerWoodWorking • • 10h ago

Equipment I love having a new miter saw

Thumbnail
gallery
53 Upvotes

I can see why I have seen people say the miter saw should be one of the first big purchases. I have no buyer's remorse with my wife anymore, she got over it 🤣

I have it pretty dialed in for angles and knocked out forty 45° cuts in about 30 minutes, and they were perfect. I have never been able to do that before. I highly recommend a digital angle finder. I bought a nice Kline one cheap at Lowes.

Once I am done building my bookshelves for the nerd room, I will make something that will be a better attachment to extend out further from the table. Until then, the level will do fine.


r/BeginnerWoodWorking • • 1h ago

Equipment Any idea if these are any good?

Post image
• Upvotes

I tried googling them, but I can’t figure out what brand they actually are.


r/BeginnerWoodWorking • • 1h ago

Instructional How do I go about cutting this butcher block?

Post image
• Upvotes

1.5 inch thick acacia wood countertop that is 30x60 and I need to cut it to 30x40. Can I use my circular saw? Should I buy a different blade for it? Any tips? I haven't used it a ton yet.

While im here any recommendation to finish it in a food safe way? I won't use it to cut on it. It is currently unfinished

Thank you!


r/BeginnerWoodWorking • • 20h ago

Trying to price piece

Thumbnail
gallery
190 Upvotes

Welder new to woodworking and built this little desk utilizing a plasma table I recently got to make the steel leg. Was thinking about listing it on market place and was curious what people on here thought was a fair price to pay for something like this without taking into account materials/time to build. Things about 4 ft long by 18in wide. Located in Fairfield county area CT for reference, lmk what ya think


r/BeginnerWoodWorking • • 6h ago

Discussion/Question ⁉️ Budget friendly wood for furniture and shelves

15 Upvotes

Hi all,

Just looking for some advise for what would be a good budget friendly durable wood to make some basic furniture and some shelving units?

I appreciate the help on this.


r/BeginnerWoodWorking • • 5h ago

Table project/things I learned for beginners

Thumbnail
gallery
12 Upvotes

I am new to real woodworking but I have a fair amount of general knowledge/experience from working with my Dad. This is my first real project that I didn't really plan on becoming what it is now but sort of snowballed into this once I started to build a "simple" workshop type table.

I'm still working on finishing the top and eventually the shelves on the long upper + lower stretchers. Originally I had picked up some "scrap" maple panels from my local Rockler that had already been planed but ripping them on the edges to glue them up made them cup and bow in ways I wasn't comfortable moving forward with, so I got a sheet of 3/4" MDO from my local store to use as a top instead.

The frame itself here is all hand done. What turned this project from a miter-and-screw job into this was trying to get the frame square and coplanar, which lead to me getting a jointer. And then I wanted to try my hand at a mortise and tenon joint. At some point I decided my goal was to try and use no hardware, only glue and hand joints and that was sort of my driving force.

The rectangular frame itself I made from old growth 2x4s from demoing a room in my house. After milling them a bit, they were so pretty and straight I wanted to use them for something. I'm not fully sure what the exact names of each type of joint is called so forgive me if I get some wrong. For the frame, the ends are joined with a blind mortise and tenon. The legs are two 2x4s that were half-lapped on one end to create a U-joint that the frame sits in. Like I mentioned, this sort of snowballed as it went, so one issue I ran into was that even though the frame rails were jointed square with one face, I did not rip the opposite edge square or plane them (at the time I didn't have access to or think I needed a planer). So when I dropped the frame into the U joints, the legs did not sit square to the frame and I had to adjust them with my chisel and then lock them in place with the triangle blocks in the corners.

That was also probably my next major mistake? Attaching the legs to the frame before I cut the lap joints for the stretchers. It certainly made making sure the laps aligned correctly was easier since the legs were already set but it made cutting the laps way more difficult, especially the short ones, because I had to shift the entire frame around to get in position to cut them. I "cheated" on the leg laps and used my circ saw to remove stock to the right depth and then chiseled them flat on the legs.

For the stretcher laps I just used a tablesaw with the miter slide and then the same. This was where I learned another lesson specifically about chisels - make sure your chisel is FLAT and SHARP. I bought a Narex chisel for this project and maybe incorrectly assumed it would be both out of the box and when cutting the first several laps, was finding it incredibly hard to get it truly flat. It caused me to keep taking more and more stock trying to get it flat when the problem was that my chisel wasn't flat enough or sharp enough. Once I flattened the back and sharpened it, that problem went away and getting the laps flat was much easier.

Once I had cut all the laps in all the legs + stretchers, I dry fit everything together and checked to see the table frame was still square/coplanar. This is where I also realized a mistake I had made which was not dry fitting all the stretchers together when I marked the lap joints on the legs. The joint placement on the legs were fine but the markings I had made on the stretchers caused me to cut the shoulders a bit short to where they didn't meet the leg. I cut pieces to fit the gaps and glued them to the leg to correct this. I also went through with a feeler gauge across all the joints with light clamp pressure to see that I was close enough for things to be glued.

After checking everything probably 50 times to make sure I hadn't missed something, I finally worked up the courage to glue everything together. Clamped all the joints together and used a pipe clamp to make sure the shoulders stayed tight during the drying phase.

Everything glued up well, frame is rigid and square. I plan for this table to live outdoors but in a covered area so while all of this was going on, I applied Outdoor Oil from General Finishes to most of the pieces that were not going to be glued and then the rest after gluing took place, with extra attention to any exposed butt-ends like the feet.

If you see the blueprint style plan at the end, you may notice that for the top, I plan to have substrate 2x4s beneath the MDO top for extra support but also to accommodate stuff like dog holes. I plan to attach the MDO top via washer head screws through clearance holes in the substrate boards into pre-drilled holes under the tabletop after I paint the top. The substrate boards I just kept simple and screwed into the frame on each end. Obviously that breaks my "no hardware" rule but this project has gone on a lot longer than expected and I really need a table to work on, lol.

Full disclosure, it didn't start this way but I ended up using GPT pretty heavily to help me plan/design and then adjust as things came up and moved forward. It was extremely useful but even I, as an amateur, noticed that some of the info it gave me wasn't always correct as far as the best way forward in a situation. My guiding principles for the table was that it needed to survive the 4 seasons in a covered scenario without me needing to rebuild it after a year. I wanted it to be long lasting, sturdy, and stable enough that it "feels like it was grown out of the ground, like a tree". I also wanted space to store tools and it helped me figure all of that out and discuss tradeoffs.

So I think in conclusion, the general tips I would pass along to other new people I learned from this are:

  • Be prepared to make mistakes and understand that 99.9% of them can just be fixed pretty simply
  • An ounce of planning saves a pound of work
  • Have the right tools - make sure things are sharp, have the right blade for the right cuts, etc.
  • You can always take more away but it's way harder to put some back
  • Understand the meaning of flat, coplanar, square, and level

I just wanted to share my work and maybe inspire someone thinking they can't into feeling like they can. The whole thing has been a huge learning experience for me on top of being fun. Happy to answer any questions if anyone has some!


r/BeginnerWoodWorking • • 6h ago

Discussion/Question ⁉️ Advice on how to clamp and connect this?

Thumbnail
gallery
7 Upvotes

I'm working on a "stuffed animal zoo" and I'm at the point where I need to connect and secure the dowels. I've posted a few times here before with questions about this project, and the determination was to have the dowels just be connected as shown in my images (forstner bit drilled notches).

Now I need to glue it up, but I'm struggling to think of a good way to do this without it being haphazard.

  1. First, is glue alone enough for this? You can see the mockup I drew on the last image here. With how shallow the dowel holes are, I wonder if that's enough glue coverage to be sturdy enough? I was considering using screws, but obviously I can only do that in one direction so I would need to choose which directions/dowels should get the screws. The wood braces are 1.25", so I suppose I could drill my dowel notches a little deeper if needed for greater glue coverage.
  2. How would I clamp this up? Maybe start with gluing two at a time, with it laid on its side? I'm just having a hard time figuring out the best way to do this part.

The second image with the dowels isn't how long they will be - I was just showing the general idea for visualization here. I just don't want to cut them yet until I have my plan on how to connect these.

Thank you!


r/BeginnerWoodWorking • • 6h ago

Discussion/Question ⁉️ Crack Repair in Thick Teak Table

Thumbnail
gallery
5 Upvotes

Am trying to figure out what the best remedy is for the cracks that are starting to appear in this teak table. Purchased in south east Asia about 5 years ago and held up relatively well and the cracks have really progressed this year as we’re in a more dry part of SoCal.

Recommendations on repair? Douse with wood oils? Fill with wood glue and then sand? Epoxy? Leave alone?

Appreciative of all recommendations.


r/BeginnerWoodWorking • • 22h ago

Discussion/Question ⁉️ Streaks in Wood from Planer

Thumbnail
gallery
66 Upvotes

It's a Dewalt 735. I raised it all the way up and cleaned out anything I could see and even switched out the blades. I'm at a loss as to what else could be causing this. Any ideas?


r/BeginnerWoodWorking • • 4h ago

Discussion/Question ⁉️ Need Help w/ Refinishing

Thumbnail
gallery
2 Upvotes

Hi peeps, my fiancé and I recently bought this table off of marketplace in hopes of giving this pre-loved 20-year-old table a new life!

It is a DWR parentesi walnut table made of MDF + walnut veneer

Our goal: Cover the fading and get an even color/stain (not looking to make it perfect or get every little scratch or mark off)

What I’ve done: 220+320 sanded and one pass of varathane stain. It didnt do much…

Hoping for some advice on how to get an even/consistent stain!

Thanks in advance.


r/BeginnerWoodWorking • • 42m ago

I have a $3k budget for a table saw and need some help...

• Upvotes

So I've got about $3k that I can use on a table saw and need some guidance on the best options.

Grizzly has the G0771Z that looks very appealing at only $1150 and the mobile base is another $120 and It's just around $1500 with freight. That would leave me theoretically $1500 to spend on a bandsaw, and whatever other stuff I would like.

I know everyone loves Sawstop so I could do the Contractor saw on a mobile base with the cast iron wings added on and the 36" T-Glide Advance Fence, and a dado brake for just over $3200. I don't need a super huge cutting surface since I already have a track saw and decently large MFT (34" x 68") but I know people have issues with the CNS when you try to tilt to 45 and dust collection problems.

And then there is the PCS from Sawstop, which with a 36" T-Glide Advance Fence, mobile base, and a dado brake will be $4200 minimum with freight.

Is Sawstop really worth 2x the money even if I am decently familiar with power tools? I know this sub loves Sawstop but so many people here recommend buying $400 Unisaws without any kind of safety feature (not even a riving knife) that also need restoring all of the time to beginners.

The Grizzly gives me more flexibility on a tool budget going forward. The CNS gives me safety but maybe not the dust collection (or bevel ability), but it's basically close enough to the budget guidelines, and then the PCS is OUT of my budget but I could theoretically save up for it even though it might take quite a while to get.

Of course there are also options from Powermatic and Jet that are within those guidelines but they're definitely Contractor saws that are more money than Grizzly's comparable option without the safety features of a Sawstop.

I'd love to hear some opinions!


r/BeginnerWoodWorking • • 19h ago

Awesome score

Thumbnail
gallery
29 Upvotes

Found this cutting board/tray at a local thrift store covered in a semi transparent paint finish. I knew it was hardwood based on weight. Paid the $2 they wanted wuth bo hesitation. Got it hone, stripped and sanded and holy crap my eyes buldged outta my head. Correct me if I'm wrong but is that mahogany??? Applied 100% tungsten oil and am letting it soak it all up. Figure I'll do s wax after it's done soaking up the oil


r/BeginnerWoodWorking • • 18h ago

How would you deal with this pitting from rust?

Thumbnail
gallery
23 Upvotes

I bought this tablesaw for pretty cheap on Facebook marketplace. I knew it had some rust on the top, but I figured I’d be able to remove it fairly easily. After I removed it though, I found this almost pitted look with some definite areas of recession.

How would you deal with this? I’m nervous to take it all the way down. Would epoxy or something similar work as a filler? I’m fairly new to all of this so I’m not sure how important it is to be perfectly flat.


r/BeginnerWoodWorking • • 1h ago

Discussion/Question ⁉️ Using Pocket Holes and Dados

• Upvotes

I am going to build a bookcase from 3/4" oak veneer plywood and I was thinking that to attach the shelves to the sides, I would cut a 1/4" deep dado and also use pocket holes to give it added strength. Would 1" screws be the correct length?

Thanks.


r/BeginnerWoodWorking • • 5h ago

Planer upgrade question

2 Upvotes

Little about me, I have a small 2 car garage workshop that I use to make my own projects. I currently have a DeWalt 735x planer, which I would sell with the stand I built + extra knives.. I have the opportunity to buy a Jet JPM 13 Planer Molder for $800. It is a 240v planer (I have 240v in my garage) + molder, though I have no idea if I would use the molder. Do you think it would be a good idea to upgrade to this? I get no additional planing capabilities since both are 13". I really would just be upgrading to get "commercial" level equipment, which could mean better longevity and maybe better cuts. The knives are straight knives.

It's the older version of this: https://www.amazon.com/708524-JPM-13CS-13-Inch-2-Horsepower-230-Volt/dp/B00002265M

I want it, but I feel like I want it more because it's "commercial" grade. I have zero complaints about my 735x, other than the knives are kind of weak -- 1 staple took 3 out. I'm really on the fence, so looking for direction. AI says it's a lot better planer than the 735 and I should do it. My wallet says I shouldn't and I'm fine where I'm at.

Thoughts?


r/BeginnerWoodWorking • • 1d ago

Quick scraps project - Cabinet drawer dividers

Thumbnail
gallery
152 Upvotes

Our drawers for pans were just empty trays, and i de ided to put some scraps to work to separate pans and cutting boards. Simple brad nails to secure them in my existing drawers and varied the spacing to match my kitchen stuff. Wipe on poly finish.


r/BeginnerWoodWorking • • 2h ago

Discussion/Question ⁉️ Help

Post image
1 Upvotes

I’ve never built anything before so don’t judge to hard… I’m hoping someone can tell me the best way to secure Spanish moss around the log. It’s going to be a stand for me European mount whitetail


r/BeginnerWoodWorking • • 2h ago

Screws and plugs

0 Upvotes

Hey all, I’m going to need to drill and plug an oak window board at home, been looking at plug cutters and the biggest I can find the Veritas cutter is 10mm. My question is, a 5mm screw has a 10mm head so how does that work exactly, I’m going to need a 100mm screw I’d say as the board is 42mm, then it’s going through plasterboard into brick underneath. Have you guys got any tips at all?