r/BmwTech • • 14m ago

2005 BMW 530i (E60 M54) – RPM surged + Reduced Power warning, now cranks/won’t start & entire car blacks out on start attempt (DTC list inside)

0 Upvotes

Vehicle: 2005 BMW 530i (E60, M54 engine)
What happened:

  1. Started the car and immediately got rapid RPM surging up and down along with an "Engine Malfunction – Reduced Power" warning.
  2. Turned the car off and tried to restart it: it would crank with the tachometer staying at 0 RPM and wouldn't fire up.
  3. Scanned with Car Scanner (ELM327) and got the fault codes below.
  4. Cleared the codes and tried starting again: the exact moment I try to start it, the entire car/cluster goes completely black (like total power loss) and comes back as soon as I let go. No new codes were logged after clearing because power cut out immediately.
    Background / Mechanic Note:
    Bullet A similar issue happened before and a mechanic fixed it temporarily by accessing the passenger-side (glovebox/fuse & relay) area, tapping/unplugging, and reseating 3 connectors.
    Bullet I haven't touched anything physically yet and want to narrow down the root cause before having it towed/worked on.
    Initial DTC Report (before clearing):
    Bullet ECU 12 (Engine):
    Bullet P0335 – Crankshaft Position Sensor "A" Circuit (Pending)
    Bullet P0340 – Camshaft Position Sensor "A" Circuit (Bank 1) (Pending)
    Bullet P0365 – Camshaft Position Sensor "B" Circuit (Bank 1) (Pending)
    Bullet P1637 – CAN Link ECM/ABSCM Circuit / Throttle Valve Position Control Deviation (Pending & Confirmed)
    Bullet P1625 – B+ Supply / Pedal Position Sensor Potentiometer Supply Channel 2 Electrical (Pending & Confirmed)
    Bullet P0444 – EVAP Canister Purge Valve Circuit Open (Pending & Confirmed)
    Bullet ECU 18 (Transmission):
    Bullet 0100 – Mass or Volume Air Flow Circuit (Pending / Stored)
    Bullet 51A7 & 51AD – Transmission faults (inhibited by other DTCs)
    Bullet P1720 – Vehicle Speed (Meter) Circuit Malfunction (Confirmed)
    Questions:
    Bullet Given the total blackout under starter load + all these simultaneous sensor/supply codes, does this point toward a bad battery/ground strap, the E60 trunk floor positive cable pass-through, or a failing relay/power module behind the glovebox?
    Bullet What should be checked first before throwing parts at it?

r/BmwTech • • 21m ago

Are any of these codes to be worried about ? - E92 335D, DPF and egr delete, stage 1.

1 Upvotes

Fault Memory
Date: 03/11/2026, 19:42
VIN: WBAWD72080PW60327
00 Junction Box Electronics
2 Errors
A6D1: ADDITIONAL WATER PUMP
A6CF: AUC SENSOR
12 Digital Diesel Electronics
5 Errors
41AA: 41AA boost pressure fan
4A70: 4A70 FMTC
_trq2qBas_MAP map incorrect
42DE: 42DE BSD - Communication with participant 7 (Gluehsteuergeraet)
4166: 4166 particle filter system
4A66: 4A66 power management wiring system (Layer_PMBN)
56 Function Centre, Roof
3 Errors
A669: Error interior light front 0xA669
A66E: Error interior light rear 0xA66E
A670: Error fitting sensor 0xA670
62 Gateway
13 Errors
E18F: Central registry does not match the target configuration (Error_Registry_New).
E18D: Awakening device has 3 times unsuccessfully tried to wake up the network.
(Error_WakeUp_Failed).
A177: External fan is not working
72 Driver's Side Footwell Module
6 Errors
9CCD: Drive mirror driver side defective
A8C5: Daytime running lights on the left are defective
A8B0: Direction indicator left front defective
A8A8: High beam or cornering light left defective
9CBF: Communication with StepperMotorBox left disturbed
9CC1: Attention: Electronics on the left headlight (SMC) reports errors
78 Automatic Heating/Air Conditioning
1 Error
9C50: Rear ventilation flap (LIN)
2


r/BmwTech • • 23m ago

BMW 220D 2014 Headunit stuck on BMW logo

Post image
1 Upvotes

I have installed an aftermarket android auto and apple car play display on my BMW 220D 2014 around 3 months ago. A few days ago I went to put my car into reverse and it's just stayed on the BMW logo ever since. The android auto still works and there audio from the speakers. The navigator wheel works and there is power to it as I can see the red light behind the text at night and I can still navigate the android auto with it. I have tried resetting the headunit on the original interface by pressing just the volume dial for 1 minute+ as well as with the mode button and also tried with the eject button to no avail. I have also tried removing the battery for 10 minutes but nothing. Still stuck on the BMW logo. Now as the car has reversing sensor I haven't yet tested whether or not it still beeps. I do have some errors come up from bimmerlink and when put into AI its saying the connections might be loose, however I don't think they are and have checked and everything seems to be fine, however when I get the time I will check once more to be sure. Just wondering if anyone has any advice? Also I've heard I may need to reflash the headunit. Is the software free and where can I find it?

Thanks for reading.


r/BmwTech • • 1h ago

2014 F20 with N55 EWS issue

1 Upvotes

Hi everyone,

*ignore the title, It must be EWG I didn’t spot the autocorrect

I’m currently having an issue with my car going into limp mode and displaying a drivetrain malfunction warning.

Based on the fault codes in ISTA, I’ve narrowed it down to an issue with the EWG, which appears to be out of specification at the closed position.
However, I haven’t been able to find much information online about anyone adjusting this on an M135i before.

Does anyone know how difficult it is to access the adjustment arm on the F20 chassis? Is it possible to reach and adjust it without removing too many components?

Any advice or experience would be greatly appreciated!


r/BmwTech • • 5h ago

BMW DRIVETRAIN MALFUNCTION

Thumbnail
gallery
0 Upvotes

I have a 2016 bmw X1 xdrive28i and recently got a drivetrain malfunction error message + an engine light. I tried driving the car; it started shaking a lot and the engine light started flashing. I instantly parked it. I got a scanner and these were the codes. but then I put some engine oil in like 4 hours later and the engine light was still on but it wasn’t flashing when driven or shaking there was just a ticking sound. can anyone tell me what might be the issue?


r/BmwTech • • 6h ago

2014 F10 535i N55 – Intermittent Parking Brake Malfunction + CAN Bus OFF Faults.

3 Upvotes

Hey everyone, hoping to get some advice from BMW techs on an issue I’ve been chasing for the past week.
2014 BMW 535i (F10/N55), 162k miles.
A few weeks ago, I noticed smoke from the passenger side of the engine bay due to a leaking valve cover/PCV system. I bought replacement parts but went on vacation for two weeks, leaving the car parked on a trickle charger. Before this, the car drove perfectly with no relevant faults.
Two days after returning, I accelerated hard from a stoplight and immediately got Auto Hold Malfunction and Parking Brake Reduced warnings. The warnings would disappear and return every ~5 seconds. Occasionally, frontal collision/pedestrian warnings appeared briefly as well.
Initially, the problem seemed movement-related, triggered by sudden acceleration or sometimes sharp turns. Leaving the car overnight would occasionally make it disappear until the next triggering event. Now the warning is constant and says “Parking Brake Malfunction.”
What’s strange is that the parking brake works perfectly. Both rear actuators engage/release promptly, hold the vehicle firmly, and release completely. No dragging or mechanical issues.
What I’ve checked/done
Battery tested good (1,004 CCA vs. 950 rated); cranking and charging tests normal.
Monitored voltage while driving: remained ≥14 V even when the malfunction occurred.
Disconnected/charged the battery overnight. Temporary improvement, but the problem returned.
Checked parking-brake fuses and visually inspected both rear actuators, connectors, and wiring into the trunk, including around the battery. Everything appears intact.
Put parking brakes into service mode and back out. No improvement.
Replaced the entire valve cover/PCV assembly and all six spark plugs. Inspected accessible engine/DME wiring while everything was apart. No visible damage or loose connectors. The original fault predates this repair.
Diagnostic codes
BlueDriver: U0075 – Control Module Communication Bus OFF.
ISTA+ initial scan: Approximately 41 stored faults, including unrelated historical issues. After clearing and reproducing the malfunction, only 13 returned, with the relevant ones being:
CD040A: ZGM – PT-CAN communication fault (marked currently present)
D3840A: EMF – PT-CAN communication fault
4809C1: DSC – EMF brake cannot be applied mechanically
D35B00 / D01B00: Missing hydraulic-function requests between EMF, DSC, and ICM
CDA704: DME missing parking-brake status message
E0840A: Gear selector PT-CAN communication fault
CF16D1: EGS missing DSC message
One additional symptom
Recently noticed a continuous humming/bubbling sound under the right-rear seat with ignition ON and engine OFF, seemingly from the low-pressure fuel pump. It stops when ignition is switched off. No starting, stalling, or fuel-pressure symptoms. I’m unsure if this was happening before the valve cover repair or if I only noticed it afterward.
Latest BimmerLink scan
CD840A: DME – FA-CAN Bus OFF (also shown as permanent)
CD040A: ZGM – FA-CAN Bus OFF
CDA704: Missing parking-brake status
CDA524: Missing electric fuel-pump status
CDA514 / 233004: Additional missing CAN messages
CF16D1: EGS missing DSC communication
The missing fuel-pump status message caught my attention given the new noise. Also, ISTA describes certain faults as PT-CAN while BimmerLink calls them FA-CAN.
Where I’m at
I’m currently leaning toward an intermittent wiring harness, connector, or CAN-bus issue, especially given the initial acceleration/turning triggers and multiple modules reporting communication faults. I’m hesitant to replace the parking brake actuators since they still work perfectly.
I’m reasonably comfortable working on the car mechanically, but ISTA is completely new to me. I used it for the first time while troubleshooting this and haven’t figured out how to take full advantage of its diagnostic functions. I managed to run the vehicle test and CAN/FlexRay system analysis, but couldn’t narrow down the fault location.
For anyone experienced with BMW diagnostics: Where would you start? Could an EMF module cause these widespread communication faults, or should I focus on the DME/ZGM and CAN wiring? Any specific ISTA test plans, connectors, or measurements you’d recommend?
I have ISTA+, BimmerLink, a multimeter, and the BMW wiring diagrams. Happy to provide screenshots or run additional tests.
Thanks!

TL;DR:
Car: 2014 535i (F10 N55), 162k miles, healthy AGM battery (tested at 1,004 CCA; stays at 14.0V+ while driving).
Symptom: "Parking Brake Malfunction" & "Auto Hold Malfunction" (plus brief FCW/pedestrian warnings). Initially triggered only by sudden acceleration or sharp turns; now persistent.
The Catch: The electronic parking brake engages, holds against throttle, and releases completely normally.
Key Codes: CD040A (ZGM Bus OFF), CD840A (DME Bus OFF), D3840A (EMF Bus OFF), E0840A (GWS PT-CAN), 4809C1, plus missing messages from EMF (CDA704, D35B00, D01B00) and Fuel Pump (CDA524).
New Clue: Low-pressure fuel pump now runs continuously with Ignition ON / Engine OFF (suspect EKPS failsafe from lost CAN comms).
Goal: Looking for the best starting point to probe PT-CAN resistance/voltage or the most likely culprit (wiring chafe under engine torque vs. failing EMF/EKPS dragging the bus down).


r/BmwTech • • 6h ago

2015 f30 320d wiper always on no horn,no blinkers

Post image
2 Upvotes

I had a short circuit in the paddle wires, and this had already happened before all of this. I removed the steering wheel to check if there were any issues and then reconnected the paddle wires.

After that, I installed everything back and started the car, but now the wipers won’t turn off.

I forgot to disconnect the battery and wait 10 minutes before taking everything apart. Could this have caused the problem? Has anyone experienced this issue before?


r/BmwTech • • 7h ago

/Inconsistent Oil reading

0 Upvotes

the oil level warning came on asking me to add 1 litre of oil (+1L), so I topped it up.
About a week later, the same warning appeared again. I didn’t add any more oil, but when I checked the next day, the oil level had gone back up to around halfway.
After driving for about 30 minutes, the low oil level warning (+1L) appeared again. This happened around 3–4 times, with the oil level fluctuating between low and normal.
Most recently, the Check Engine light suddenly came on while I was driving at the morning, but at evening the Check Engine light dissapear.
I’m not sure if these two issues are related or if the oil level sensor is faulty.


r/BmwTech • • 8h ago

2017 X-3 X- drive 228i. Automatic 4wD (Two similar issues)

2 Upvotes

Usually before the car is fully warmed up, as we start to drive, the car doesn’t shift up. around 4000 RPM The engine will begin to run rough. Taking our foot off the gas’s the car decelerates as if in first gear. After making a complete stop the car will shift like normal. Another symptom is driving at highway speed the car will suddenly feel like it coasting, no change in RPM but slight speed decline. Stepping into the gas doesn’t cure it, but it usually resolves itself within seconds. The mechanic says there are no relevant codes, being thrown, just “ body codes”. Any Beamer buddies out there could point me in the right direction about resolving this difficulty, im thinking throttle body sending unit but not confident ??


r/BmwTech • • 9h ago

Original Spark Plugs at 140k miles

Post image
3 Upvotes

Bought a used X5 and after a month it started misfiring on cylinder 2, moved the coils from cylinder 1 to cylinder 2 and now I got 2 misfires. Battery needs a replacement, I am hoping that when I replace the spark plugs, coils, and battery the misfire will go away. What are the chances that the DME is gone wrong? how would you go about diagnosing?


r/BmwTech • • 11h ago

How to find a catalytic converter independently

1 Upvotes

F30 BMW 330e 2018reg. I bought this car and it was catless (which was careless) with a straight downpipe and custom exhaust (twin tailpipes) and I’m trying to restore and remove the mods ahead of my MOT in a month. Not really a knowledgeable car guy so went to a mechanic who told me if I find the parts he’ll put it back together for me after I showed him a video of what the exhaust system looks like.

I’d need the 18328630246 (got from realOEM.com) but any that I have been able to find on eBay uk are looking quite poor, and the search has been quite stressful. I read that if I don’t get the EXACT OE parts then my sensors would go off and I’d fail my MOT anyway because of the way the hybrid sensors interact with the catalytic converter. An option is I get it ordered from BMW but I don’t have £3k to spend on this (including the exhaust system).

I was hoping the restoration wouldn’t take more than a £1k which I could reluctantly deal with and accept as punishment for being an idiot, but honestly don’t know what to do. I mean even GTA6 launched 20 mins ago and I’m not even playing it I’m so deflated.

Am i looking for parts the right way? (Currently just looking through the google links in shopping when I type my part code in).

Do I just sell the car? (I imagine someone would want this type of custom set up but it just doesn’t feel right to it).

Options or advice anyone can offer?


r/BmwTech • • 11h ago

2020 BMW118I drops audio during Apple car play calls.

1 Upvotes

My wife has a BMW118i and it constantly drops audio during Apple CarPlay phone calls. All of a sudden she can’t hear me talking but I can hear her and I have to ring her back.

It’s usually when going under e toll readers but also happens at traffic lights with cameras etc.
It’s like the signal drops the audio but it doesn’t reconnect.

She can’t use a cable for car play as none of the 2 usb ports connect to the infotainment unit like it does in my Ranger.

She took it to BMW who charged $350 to tell her it’s her battery that needs replacing and wanted to charge her $900. Yet it’s never not started even when sitting for a week.

What else can we do to try and fix this?


r/BmwTech • • 11h ago

Crank hub capture plate nightmare S55

Post image
1 Upvotes

Just wanted to spread some knowledge I have learned about these crankhub capture plates after having 2 bolts back out (2015 m4). Almost every single one on the market is absolute garbage, they come with cheap Chinese bolts and a horrendous amount of clamping area. These were tqd to 25 ft lbs with red locktite and still backed out. The bolts dug into the aluminum on every one and I’m assuming that’s why it lost clamping force. Just got a MALO industries plate and it has optional ARP bolts and a single washer so all bolts have even surface area. Do not get one if it is not a single washer with ARP bolts or you will do a lot of damage.


r/BmwTech • • 12h ago

Frustrated with ABS pump malfunction

Post image
2 Upvotes

Hello everyone!! This is my 1999 528i 5spd that is currently dealing with a horribly frustrating ABS pump malfunction causing my rear brakes to be seized. I purchased the car with the locked up brakes thinking it would be a relatively simple fix. The gentleman I got the car from recently passed away and hardly ever drove the car.(3.5k miles in 17 years of ownership car now has 153,000mi.) After getting the car home I contacted the previous mechanic that fixed the issue in 2024 by sending the black electronic module to get rebuilt and he said it could possibly be calipers so I changed those aswell as every component related to brakes like master cylinder and brake booster. After giving up for a few months I finally caved and brought it into a shop for them to tell me the ABS pump is faulty. A replacement one is no longer produced and it would be $3500. I would just find one off eBay but the issue I’m running into is I was in kind of a weird gap year with a very weird design that only spans about 18 months or so where at has ASC+T in the engine bay. SORRY FOR RAMBLING I DON’T KNOW WHAT TO DO. ANY HELP WOULD BE GREATLY


r/BmwTech • • 12h ago

handbrake issue on my F30 2016

1 Upvotes

my car is at 134K miles , my handbrake has excessive clicks and the car sorta rocks back a bit when engaged , i’ve tried adjusting it through the rear wheels , could my handbrake shoes be worn in somewhat savvy mechanical i just don’t want to fix something that isn’t broken , ive no history on if it was ever changed before is this the right approach? thanks


r/BmwTech • • 12h ago

Are my turbo seals leaking?

1 Upvotes

Hi,
I have a 2012 e92 335is (n54 motor) that is leaking large amounts of oil and blows smoke out of the exhaust upon start up but is running fine and not down on power. I took the car to my mechanic and he said the turbo seals are leaking and I need new turbos. He sent me a video but it’s hard for me to see the turbo seals leaking. I was wondering if anyone here can see the seals leaking from this video. If so, is it time to replace the turbos?


r/BmwTech • • 12h ago

F31 timing chain guide

0 Upvotes

Hi all,
I’ve got a 2014 f31 and I’ve read that timing chain guide failure is a common issue on cars over 100k miles
I can’t recall if it’s always sounded like this or if this is the metallic or whining sound I’m supposed to look out for. Any advice is appreciated
Thank you


r/BmwTech • • 13h ago

Rear differential sound

1 Upvotes

Is this sound like an early warning of the rear differential failing?

2022 G21, 320i M sport (not modified)


r/BmwTech • • 13h ago

N54 30FF Error Code

1 Upvotes

Looking for advice on how to troubleshoot this 30FF code. Got the half engine warning light for the first time yesterday driving home from work. Ran Bimmerlink and it found only one error code - 30FF. I cleared the code last night and driving to work today it popped up again while I was on the highway.

Car runs OK but power and throttle response are reduced.

It’s a 335is n54
Bone stock
Well cared for
57k miles

Ive recently replaced all 6 injectors with index 12
Replaced OFHG
Replaced valve cover and gasket

It has done it 2 more times in test drives today. Pulls fine for the first few minutes, then the half engine light comes on and it goes into lower power mode. Seems to drive OK, but just not full boost perfomance.

AI thinks it could be a bad vacuum line...

Any recommendations on next steps to resolve this?


r/BmwTech • • 14h ago

Trying to catch up on MX from previous owner. 2019 m240i xdrive. Was told not to do transmission fluid by dealer.

3 Upvotes

I went to the dealer to get a quote on stuff i needed done, just passed 85k miles and the previous owners only did engine oil and a couple brake flushes and one pad slap two years ago. So I went and asked about coolant flush, diff and transfer case flush, trans fluid, oil change, and a cabin fan because its squealing.

The advisor wouldn't give me a quote on the transmission fluid because he said it was life time and they recommended to not touch it unless there were issues, and the rest excluding the fan was quoted at $1,700.

The argument for the transmission seems to be strongly in both the yes and no so I have no idea what to do there. This is also my first time owning a BMW so I don't know what to believe here. Im just looking for general advice.


r/BmwTech • • 14h ago

2018 530e Turbo coolant Line

Thumbnail
gallery
4 Upvotes

I need advice…went to BMW. They replaced the starter for the recall. They noticed a leak and saying it’s about $3000 to repair. That is kinda expensive for me. Any advice? Also any reasonable recommendations in SoCal:La County or Orange County area.


r/BmwTech • • 14h ago

G20 330e repair advise

Thumbnail
gallery
0 Upvotes

After my 320i got totaled by a drunk driver 5 months ago now a delivery driver ran into my parked 330e. Is the bumper repairable with this damage or does it need a new front bumper. Thanks!