r/Bowyer • • Jan 12 '21

Community Post How to post a tiller check

Thumbnail
gallery
508 Upvotes

r/Bowyer • • Aug 16 '22

AMA Ask me anything - Correy Hawk

Thumbnail
gallery
278 Upvotes

r/Bowyer • • 7h ago

Bows I Got Two Manchu Horn Bows Today

20 Upvotes

51@34”
All natural horn sinew fish glue birch bark traditional wrapping


r/Bowyer • • 1h ago

Peering through the bow to find its purpose!

• Upvotes

r/Bowyer • • 5h ago

ARROW GRAIN HELP

3 Upvotes

The internet keeps saying that for a 28lb bow, 160-200 grains for the shaft is ideal.
I have made a 30 inch hazel shaft that is 38 grams = 586 grains.
How is this possible? It looks thinner than most DIY arrow shafts online and yet is somehow more than twice the recommended weight. (yes the wood is dry)

Am I missing something ?


r/Bowyer • • 3h ago

HEAT TREATING

2 Upvotes

Which bow position leads to the least amount of heat getting to the back?
- Heat gun pointing down --> bow belly side up
- Heat gun pointing up --> bow belly side down


r/Bowyer • • 1h ago

What type of Hickory is this?

Thumbnail
gallery
• Upvotes

I can’t decide if this is mockernut, bitternut, or pignut hickory. Anyone have an idea what it is?


r/Bowyer • • 1d ago

I tested 10000 virtual bows so that you didn't have to: a study of design factors and bow performance

Thumbnail
gallery
128 Upvotes

Hello everyone

I wanted to share a little side project I've been working on the last few weeks.

Full disclaimer: While I do have a degree in engineering (in a completely unrelated field) and work with computer modelling and coding for my real job, I couldn't have done (much less had time for) this work myself, and all this is extensively vibe coded (using Claude Code), both for the bow model and for analysis. That said, the design choices, the details of the implementation and interpretation are my own as a bowyer - I also couldn't have done this without being an experienced bowyer. If AI is a deal-breaker for you, please ignore this post.

So, I created a program that randomly generates bow designs, drawing from a pool of preset design element ranges - such as length, width, width profile, lever length, deflex, reflex, recurve and so on. The program then attempts to autotiller the bow to an ideal tiller shape for that design. The bow is rejected if it fails a number of sanity checks (e.g. too narrow for stability on reflexed/recurved bows, practical length/width limits, minimum limb thickness, etc.). The exact methods as well as all the design ranges and constraints are described in the pdf linked in this post.

What I mean by "optimal tiller":

This is basically another way of saying something which all design-fluent bowyers know: The best bend at full draw depends on the front profile! Given a certain front and side profile, the optimal tiller is always the one that gives even strain along the bow limb. This doesn't mean that the bow bends evenly, but that its bend and bow thickness combine at each spot along the limbs to compress wood fibers to an even amount along the bow limb. Thick parts must bend less, and thin parts must bend more, to achieve this. A wide part has more wood at a given thickness, so must be thinner, and bend tighter, to provide the same resistance as a narrower, but thicker, and less bending part. That is why optimally tillered pyramid bows, with more width taper, bend more evenly, and why parallel limbs must be elliptical (bend to a tighter radius as you move further along the limbs). The key here is that when they bend optimally, they will have even strain, meaning that all the wood in the limbs is working the same amount. I also tested this assumption, see below. Finally, a bow that is tillered to too high a strain will be overstrained, and take more set, while the opposite represents an understrained bow that will have too much mass in the limbs.

First off, during the work on the bow model parameterization, I realized something really nice about bow wood properties:

Steve Gardner's mass principle from first principles!

At a given strain, the best bow wood is the wood that is stiffest per density. As strain rises, you get more work out of the same amount of wood, making the bow more efficient. Of course, when you run into the limit of how much you can strain the wood before it breaks, the party is over.

Stiffer limbs store more energy at the same strain, while denser limbs make heavier limbs, which are less efficient. Most white woods are much stiffer per density than the "classic" bow woods (Yew, Osage), so why are Yew and Osage woods regarded so well? When you analyze data from the wood database, it turns out that, relative to density, wood stiffness and crushing strain are negatively related, meaning weaker-per-density woods can generally bend further before taking set, and thus make up for their weak resistance. Another way of saying this is that stiffness per density, combined with how far the wood can bend before taking set, gives roughly the same stored energy per pound of limb for all bow woods, which makes them about equal in performance. Imagine a sort of performance triangle of density, stiffness per density and elasticity which fits all wood species inside it, all different, but in a way where all woods end up with limbs that weigh about the same, just narrower and thicker, or wider and thinner. This is basically Steve Gardner's mass principle, but derived from the bottom-up, going from the basic properties of wood, where he derived it through years of empirical experimentation. I find this incredibly satisfying and beautiful, that working from each end of the method spectrum, you end up at the same conclusions!

At the end of the day, though, for comparing different designs, the properties of the wood don't actually matter for the relative performance of different designs: It only determines the maximum draw weight that can come out of a certain set of bow dimensions (which is of course important to an actual bowyer, but not useful for comparing designs).

The test

I ran about 10000 bows, all scaling the width/length to achieve 50 lbs at 28 inches of draw, covering the design space evenly, and recording how speed depends on the design, given that the bow is in all cases tillered optimally (even strain). As no bowyer is perfect, and recognizing that set in the inner limb is the absolute worst place, I incorporated a safety margin, which ensured that the inner limb gets a 20% strain discount that tapers out into the limb. Doing away with this limit represents a flightbow, make-it-or-break-it scenario.

If a design passes, a copy of the bow design is ported to a VirtualBow file, and "fired" using the VirtualBow dynamics solver Python implementation, at 10GPP, and the resulting arrow speed recorded. This has not been calibrated to actual bows, so take the absolute bow speeds with a grain of salt, although if memory serves, I've seen laminated bowyers report dimensions and performance between VirtualBow and real bows to correspond well.

What determines bow speed:

Here's where you get disappointed/elated, depending on temperament: The results more-or-less confirm what we already know about bow performance, no big new revelations! Go and read the TBBs, if you prefer that, and rest assured that the conclusions presented there have really stood the test of time. I don't think people like Tim Baker, Steve Gardner and others can really be praised enough for the quality, tenacity and brilliance of their work.

The main results:

The pics above are the fastest bows of each type modelled: A pyramid, a recurved flatbow, a lever bow, and an ELB; all reflex/deflex designs, except for the ELB, in which reflex/deflex designs are not allowed by the program.

Bear in mind that some of the conclusions below will depend somewhat on my choices for limits on design specs. It seems that at the very bow speed frontier, bow speed is generally constrained mainly by construction and indirect constraints such as sideways stability and heat-bent recurve stability stiffness requirements, so my constraint rules play an important part in setting boundaries on max speed. I encourage everyone interested to read the pdf, where there are many more details on execution, design limitations, and results! I'd really like feedback on where I am too lax/strict on limiting the extreme designs.

  • I tested varying limb strain distributions at the same draw weight and bow dimensions in VirtualBow, just to confirm the even strain conjecture, and in every case they came out slower than an evenly strained bow. The differences in arrow speed are about the same as those coming from the design elements themselves, so the importance of picking the right tiller shape for your bow design is as important as the design itself!

  • Optimally tillered bows are FAST! The slowest bows in the test shoot somewhere around 175fps, relative to around 190fps for the fastest. The exact speeds here should be taken with a grain of salt, but still. 9 out of ten bows are around 179-186 fps.

  • The closest thing to a magic bullet in bowbuilding really is the reflex/deflex profile. It increases speed through efficiency (deflex) and energy storage (reflex), and is the main factor explaining speed differences in the tests. The only things that really trade against it are limb taper and bow length/width ratio, where you run into my imposed constraints that R/D bows need a certain width at midlimb to be stable. Otherwise longer bows and more tapered bows are somewhat faster (through increased energy storage and efficiency, respectively), but this is mostly overshadowed by reflex/deflex in the model data.

  • Recurves do increase speed, through energy storage, but some of that gain is swallowed by heavier limb tips, when the recurves are constrained to be stiff (for not pulling out). In an earlier test, where working recurves were allowed, they did increase speed to a higher extent.

  • Lever bows are fast, but not the fastest. They win through efficiency mainly, in contrast to other fast designs. Levers are naturally stiff, but will only increase performance if strained relatively close to the working limb limit!

  • The fastest designs win mainly through high energy storage; for these optimally tillered bows, efficiency is generally pretty high, and the design specs are designed to reduce tip mass as much as possible.

  • In an otherwise straight, optimally tillered bow, a bit of handle deflex (net deflex of an inch or so) doesn't cost any speed; reduced limb mass makes up for less energy storage. Otherwise, straight bow speed depends mainly on length.

  • Reflex increases performance, but only if it is placed in the outer limb (it increases energy storage through string angle). In an earlier test, I tested bows with evenly distributed reflex along the limbs. They were generally slower than straight counterparts: Though they have slightly higher energy storage, the gain is completely negated by heavier limbs. This is contrary to a lot of established thinking, but I think many bows benefit from being evenly reflexed because they were originally understrained. In that case, it can increase performance by bringing limb strain closer to the limit.

Tension and compression

One thing I apparently misunderstood, which I think does also apply to many (most?) other bowyers, is related to tension/compression strength in wood. It turns out, wood is actually close to equally stiff in tension and compression, so the neutral plane is more or less in the middle, as long as the bow is not overstrained. The difference is in compression/tension STRENGTH, meaning the point at which the wood starts to break down; once this happens, the neutral plane does move towards the back in a sort of "death spiral".

Full methods and results (PDF)


r/Bowyer • • 2h ago

can you interrupt heat treating half way through and pick up the next day?

1 Upvotes

r/Bowyer • • 4h ago

Robinia stave with a knot on the limb - Need advice on design and handling

Thumbnail
gallery
1 Upvotes

Hi everyone, after a lot of study and research, finally decided to buy a seasoned hickory stave and a seasoned robinia stave.

I'm planning to work on the robinia one second, but it has an issue: there is a knot right on one of the limbs. I'd love to go for an American flatbow design, but I'm not sure how best to handle theknot.

Could you give me some advice? Is it better to incorporate the knot or work around it, considering it is close to the edge?


r/Bowyer • • 10h ago

ARROW HELP

3 Upvotes

I've been trying to understand grain and spine and whatever else is needed to make these godforsaken things, but I just end up confused.
I'm trying to make hazel arrows to shoot from my 27/28 pound, 28 inch draw, 65 inch long hazel selfbow.

How do I calculate the shaft weight & anything else I would need to know ?

I made a 29.5 inch shaft weighing 38 grams, with the tip tapered to a point.
Is it anywhere near the right weight/dimensions?


r/Bowyer • • 21h ago

Me lleva la mierda

Post image
13 Upvotes

Supongo que a la proxima tratare de usar una mejor madera... Aunque el encino y el fresno ya me habia dado buen resultado este arco no aguantó y explotó... Tratare de conseguir madera de tejo para un arco de guerra este ya valio madres

Tantas horas de trabajo tiradas a la basura y ni siquiera fue por un error simplemente aveces que la madera no quiere cooperar; salganse de reddit quiero estar solo 😔


r/Bowyer • • 8h ago

Consumer Advice Cosmetic or structural damage?

Thumbnail gallery
1 Upvotes

r/Bowyer • • 12h ago

Questions/Advise Propeller twist green BL fix

Thumbnail
gallery
1 Upvotes

I went through all posts here about untwisting green cut staves. My BL halves are abt 45 degrees twisted, cut yesterday. So I prepared this improvised jig. Halves are abt 4 inch diameter. I am afraid that this jig using 2 weights on both sides about 6 kg each will not be sufficient? And I risk to get limbs bend? Should I work on the stave to reduce into a bow shape and than to try untwisting? Anyone with similar experience?


r/Bowyer • • 1d ago

Poor Mans Sauna

Post image
7 Upvotes

Just a kettle on an induction stove under a tin foil tent and a towel behind…cowboy steam bend! I straightened out my propeller twist 🙂


r/Bowyer • • 21h ago

Can I make a bow from this

Post image
1 Upvotes

r/Bowyer • • 1d ago

Board bows

8 Upvotes

I'm not sure if this is the right place to ask but I'm getting into bow making and for the first one I was going to try a board bow. I've watched a lot of how to videos and I'm sure I'm just missing it but when using Osage you follow a ring correct and does this work for Osage boards? Also for white woods i know you don't need to follow a ring but I guess I'm confused on why not and what needs to be the back of the bow for white wood or if it matters as long as the grain is straight on all sides of the board.


r/Bowyer • • 1d ago

How to improve at judging tiller?

4 Upvotes

What I mean is, people will post tiller pics here and to me it looks pretty OK. Then the more experienced guys will chime in with specific tips and only then do I see what they're talking about.

I've been re reading Bowyer's Bible to see if I missed something about tillering the first time through. I'd love to know some concrete steps I can take to get better at this

Also, I mostly use a tiller stick in my own builds - is it worth it to switch to a tree instead?


r/Bowyer • • 1d ago

Questions/Advise Splicing white wood billets

3 Upvotes

I read in TBB 1 that Osage and white woods should be chased to a single growth ring before splicing.

I thought white woods (in this case, Elm) didn’t need to be taken down to a growth ring?

Also, doesn’t the act of splicing and sanding down the epoxy create a mess of the back anyway?

What’s the easiest way to cure EA40 without a heat box?


r/Bowyer • • 1d ago

Update for splitting the mulberry stave

Thumbnail
gallery
6 Upvotes

Still same length I chose the side have less knots one it did look like can turn In to bow. (Also it smell like saliva or organic does it normal?)


r/Bowyer • • 2d ago

Tiller Check and Updates Long string tiller check.

Thumbnail
gallery
25 Upvotes

This is a 70 inch Ash recurve board bow I’ve been working on. I think my next step will be fire hardening the belly before further tillering.
But I would really like to hear some thoughts and get some feedback from some of you guys! :)


r/Bowyer • • 1d ago

Can anybody sell to me sinew?

4 Upvotes

I need sinew for a hornbow but in ebay is too expesive... Not the product, the shipment is the double... I dont know if anybody can sell to me some sticks please


r/Bowyer • • 2d ago

How to find a local mentor?

4 Upvotes

Are there by any chance any bowyers in here from Kitsap Washington? Or would anyone have a lead on how to find some local classes?

Searching for local bowyers hasn’t provided.


r/Bowyer • • 2d ago

sinew backing a board bow

3 Upvotes

Hey all, im considering my next bow build, and given that I am not fully interested in working a whole stave, I am considering firehardening a hickory board stave, and then sinew backing it with just 2 layers of sinew. Hoping to get a bow that is roughly 54-56" long, 45-50lbs at 24", has fairly narrow limbs(1.25"ish with a slightly narrowed handle, has 2-3" of backset, and bends through the handle if needed. any pointers on going this route? My main concern is I am wanting a bow that looks very very primitive, but shoots incredibly fast for what it is, im even considering doing a linen strip for it so it is still a natural material string, but basically the fastest one possible.


r/Bowyer • • 2d ago

Choctaw Osage Orange Bow

Thumbnail
gallery
49 Upvotes

Some good inspiration here. Late 19th or early 20th bow probably made in Oklahoma. It's part of the Grayson Archery Collection and is on display at the University of Missouri Museum of Art and Archeology. The grip is twisted plant fiber cordage.

Length: 56.2"
Max Width: 1.5"
Max Thickness: 0.8"

More on the Grayson Collection: The Grayson Archery Collection at the University of Missouri’s Museum of Anthropology contains more than 5,500 archery-related objects from six continents. Donated by collector Charles E. “Bert” Grayson, it includes bows, arrows, arrowheads, quivers, and other objects. Dr. Charles E. “Bert” Grayson was a physician, bowyer, and competitive archer who spent a lifetime studying and collecting archery equipment. He began donating his collection to the University of Missouri Museum of Anthropology in the early 1990s. (anthromuseum.missouri.edu)