r/CarbonFiber • u/lolsborn • 6h ago
Filar: Custom filament winding software
r/CarbonFiber • u/CarbonGod • Nov 20 '24
With new printing methods, the traditional fake CF that looks like it was printed in black and white, with no texture giving it a 3D look, it will be harder to tell. If a part is made perfectly, it won't have weave distortions, but that is rare. Also, look for parting lines, and fabric seams in logical places like edges. If it looks like someone just cut a sheet of plastic, then that seam will look exactly like that. Surface finishes also effect what you can see being real or fake. Matte finishes hide the high definition glare and weave diffraction.
r/CarbonFiber • u/CarbonGod • Feb 19 '25
I'll try to find a place to make a list, but I happened to see these two books in our library, so they might be a good starting place for those interested in composites, but have NO idea about it!!
Intro to Composites, 4th Ed, Composites Institute NYC. ci@socplas.org No ISBN
Composites - A design guide, Terry Richardson 0-8311-1173-9
Second is a bit older, but only the details change through the years.
r/CarbonFiber • u/LegendaryHD • 1d ago
Hey everyone!
I’m planning to make this part out of chopped tow carbon fiber using the Easy Composites beginner kit I bought a while ago. I’ve made a few smaller parts with it, but this would be my first larger project.
The part is approximately 200 × 500 mm, with a 3 mm thick main plate and raised edges up to 10 mm thick.
I’ve designed a compression mould that I plan to 3D-print in PETG. I’ve added draft angles and fillets wherever possible and will pay attention to the print orientation to make demoulding easier (learned that the hard way…).
My plan is to orient the mould with the flat plate facing upwards and press the upper mould half down into it.
I have a few questions:
Mounting holes: Is there a good way to integrate the holes directly into the mould? I could drill them afterwards, but their positioning needs to be quite accurate.
Fiber-to-resin ratio: I’m concerned that the thicker edges won’t compress properly, potentially resulting in too much resin in those areas. How would you approach this? I also considered making the 3 mm plate and the raised edges separately and bonding them together, but I’m unsure about the strength of the bond.
Other potential issues: Do you see any problems with the design or manufacturing approach that I might be overlooking?
Any advice or suggestions would be greatly appreciated. Thanks!
r/CarbonFiber • u/AviationMetalSmith1 • 3d ago
An unusual car with a fiberglass body.
r/CarbonFiber • u/bAr559 • 3d ago
Finally got my hood in after 2 years of waiting but has damage on the corners wats the best way to go about repairing the corners?
r/CarbonFiber • u/qwpo_booga • 5d ago
I'm making an airplane wing with two top and bottom female moulds. I applied 5 layers of wax and buffed between coats. Should I apply PVA, and if so how many coats? (I don't have a sprayer)
I would strongly prefer not to treat my surface after demolding want to transfer the mould finish.
r/CarbonFiber • u/TLDREGE • 5d ago
Hello guys these were matte finished so I sanded down and applied 2k clear coat about 2 months ago. They were looking great. But yesterday I realised that there is something on them. I dont know what it is but you can hear it on the video. Its something solid. When I rub my fingers or apply ipa it becomes sticky but cannot take them off at all. Probably there was something on the road sticked to them. Idk.
Tried
- IPA - wont take off and spreads it.
- tar remover didnt took it off did nothing really
- vinegar did nothing
- warm soap water ofc didnt do anything
Since its becoming gummy on my fingers would it be best idea to polish them - idk too.
Any suggestions on what to do ?
r/CarbonFiber • u/Jealous_Message5226 • 6d ago
Hello everyone, im thinking of buying a front lip and spoiler for my car and im thinking just buying both of them fake Carbon fiber, I just wanted to ask before purchasing them what are some problems or cons that i could run into from buying them? Like will they look weird after a while or will heat ruin them?
If theres lots of potential problems might just buy in glossy black instead
Thanks
r/CarbonFiber • u/TheRealSweet • 8d ago
Any ideas on how to make the hood fit better or am I just unlucky with the hood I got
r/CarbonFiber • u/MotorsportX • 8d ago
Beginning of tests Carbon Fiber cases of pitaka. I have now and will receive some more cases and make soon full tests review
r/CarbonFiber • u/AlonePlenty • 10d ago
Ilmberger carbon fiber frame covers. These are normally about $600 new from Germany and I got these for $150 from a crashed BMW S1000RR parts lot. Planning on using these for my ‘17 S1K.
Appears to be some fade, a hole, and a medium sized dark spot. I have yet to receive them but plan on trying to restore them as a DIY project. I’m not looking for perfection but definitely trying to give them some more life.
Thanks for any tips!
r/CarbonFiber • u/Zaph5 • 10d ago
Je vais troquer mes jantes alu contre des jantes carbones et j'ai déniché une bonne affaire sur lbc.
Malheureusement, la roue avant a pris un pet (le vendeur pense que ça vient d'un cailloux en roulant).
Est-ce que un red flag ou bien je peux y aller ?
Merci d'avance !
r/CarbonFiber • u/Darknesgamer36 • 11d ago
I am planning on buying this trunk and getting the clear coat redone by a shop. I am wondering if the fiber is damaged beyond saving, or it should look good with a new clear. The owner states it is a Vis Racing. In the last two photos the trunk is wet. Thank you!
r/CarbonFiber • u/Past-Piccolo-2157 • 11d ago
I need some expert opinions/advice on this one. 2016 Polaris RZR turbo hood that I'm skinning for a friend... Should I lay these pockets down first in their own layer and then the rest of the hood afterwards? Ooorrrr what? I'm afraid to lay it up in one piece because these pockets have the craziest geometry and it'll distort the surrounding areas.
3k plain weave
r/CarbonFiber • u/want_a_mustang • 11d ago
None of the factories around here make this wing in dry carbon — any idea why?
r/CarbonFiber • u/OkField5046 • 12d ago
Hello,
I’ve just noticed my wet carbon fiber mirror caps have white spots in the weave.. these were not present a few days ago. I do live in a colder environment. It has been down in the freezing temps a few nights. How does this happen? Can anything be done? I can feel a “bump” where the white spots are.. any help or info would be appreciated!
Thanks