r/maker • • 19h ago

Showcase I made a little place

Thumbnail
gallery
164 Upvotes

Built this over the summer for camping

When gathering materials, I did my best to fight that urge to just go and buy the material designed for the application, and often discovered an equal alternative. It was my favourite part of this project. A free old cap as a roof, scrapped lumber, extruded aluminum picture frames as trim, aluminum dryer vent tape as a new paint job, MCM board as pin striping, and the list went on.

As far as construction, I approached it more like a carnival game or prop than anything else. Designed for quick (dis)assembly with almost no tools, while being ridged and secure.

Thanks for checking it out!


r/maker • • 3h ago

Showcase Meet Zeke V2

5 Upvotes

My second stage of development for my animatronic friend.


r/maker • • 14h ago

Multi-Discipline Project DIY an automatic treasure-hunting robot.

13 Upvotes

During this period, we have been continuously focusing on technological research. We have already developed our own remote control, and our detection information can be displayed on our remote control as well as marked on a map. Next, we will continuously test and debug our self-developed disk data to make it more effective. The second video has already achieved automatic cruising, and we will r/DIYMetalDetecting/ We will update our progress.


r/maker • • 9h ago

Help Stubborn acrylic paper film

Thumbnail
gallery
4 Upvotes

Does anyone have tips on ways to remove the pesky paper film from very old acrylic? You can’t use anything too abrasive or it will scratch the surface. Alcohol and other aggressive agents typically damage acrylic, making it cloudy or brittle by drying it out.

I’ve been in the graphics and signage industry for over a decade now and most of what I’ve saved came by way of soaking it in RapidTac. (I hate the citrus smell of removers, so it’s never my first option)
This clearly didn’t work here as it’s likely much older than anything I’ve used professionally. My attempt was to get past the waxy paper and allow the liquid to better soak in.

This stuff came from a warehouse in Chicago selling random stuff by the pound for $1. It was a dream for me, almost like the junkyard Laura Kampf frequents out in LA. That said, I could toss it without much lost. But the colors in this stack are beautiful and I don’t see them often.


r/maker • • 1d ago

Multi-Discipline Project Building kinetic sculptures (with zero experience)

5 Upvotes

It started out as a cardboard robot costume to wear for a nature education event, and it has since taken over my whole brain... I have big dreams for NatureBot 2.0, but to make them happen, I will need to expand my skill set.

Up until this point, I've been more of an artist than an engineer. I can knit, sculpt, paint, sew, etc., but when it comes to anything you might learn in shop class, I'm oblivious.

To add functionality and surprise to this costume, it would really help to understand things like how to make things like custom dials, how to choose the right fasteners and adhesives, and plenty of other tinkering skills I haven't even imagined yet.

I'm willing to get pretty hardcore in pursuit of becoming a better maker, and I have access to a variety of tools, space to work, etc. What I'm missing is a curriculum. What should I start with?

I don't even know if I have the vocabulary to describe what I want to achieve, which makes it hard to search on my own. I've started to look around for broken toys and gadgets to deconstruct.

Are there videos, books, kits or classes you can recommend for the absolute beginner?

*I've asked for some browndoggadget kits for Christmas, because that will help with setting up lights and motors, etc., in a fabric-and-cardboard friendly way


r/maker • • 1d ago

Showcase Finally posting the halloween mousepad i cut on a 40w. Total overkill, but it worked

Post image
7 Upvotes

My wife wanted a halloween mousepad. I was too lazy to dig out the cricut mats and blades, so I just threw the felt sheets on my laser (an Aliencell) instead.

Snapped a photo of the bed on the screen, dragged the files over the different colors, and let it rip. No tape needed. Only downside is if you look close the edges are a little crusty, and my office smelled like burnt hair for the rest of the day lol. Still for a 10-min craft I'll take it. Anyone else use their big machines for tiny dumb projects?


r/maker • • 1d ago

Inquiry Munchkin Straw Cup Lids

Thumbnail
gallery
0 Upvotes

Hi! Does anyone know of any files that I can print a new straw cup lid?


r/maker • • 2d ago

Video A roll of copper wire, a moonstone, and a lot of patience.

82 Upvotes

r/maker • • 1d ago

Showcase Engineering a budget-friendly, 6-DOF CAD mouse (NaviGo). Dropping the DIY files soon! 🛠️

1 Upvotes

Just wanted to share a sneak peek of a project I've been working on: a fully functional, DIY alternative to the SpaceMouse, built for under $15.

​Current Specs:

​Powered by Raspberry Pi Pico + ADXL335

​Custom Python Add-in for Fusion 360 (silky smooth Pan, Orbit, Zoom, Roll)

​Hardware theme switcher with on-board memory (Cyberpunk, Matrix, and Fire themes)

​Smart directional LEDs that light up based on where you push/pull.

​I'm currently writing the assembly guide and finalizing the STLs/code for release.

​If you're interested in building one, let me know below and I'll send you a link as soon as everything is published! Any feedback on the design is also highly appreciated!

Here is yt short for it

https://youtube.com/shorts/xIgNhH2CMgI?feature=share


r/maker • • 2d ago

Video Chevy 350 sprocket lamp

10 Upvotes

Made from a used timing set from a Chevy 350. Valve cover im not for sure. Thsnks for looking!


r/maker • • 2d ago

Inquiry What's one part you wish you could manufacture in your own workshop?

1 Upvotes

One of the most frustrating things about DIY projects is having a design that works on paper but requires a custom part you can't easily make at home.

Regular 3D printing solves a lot of these problems. You can make custom adapters, enclosures, tools, and replacement parts without waiting for a machine shop.

But there are still situations where plastic alone isn't quite enough, especially for parts that need higher stiffness or mechanical strength.

I've been exploring FibreSeeker's continuous fiber 3D printing technology, and the interesting part is how it could expand what makers can produce themselves. Instead of choosing between a standard plastic print and an expensive machined component, reinforced printing might offer another option for custom functional parts.

That could be useful for everything from workshop tools and mechanical assemblies to small-batch hardware projects.

What's something you've wanted to make but couldn't because regular FDM wasn't strong enough or machining was too expensive?


r/maker • • 2d ago

Showcase I’ve updated my portable soldering station.It’s now at 45 degrees for easier pickup, mounted with a 1/4 screw on the power bank.Do you have any suggestions?

Thumbnail
gallery
0 Upvotes

r/maker • • 3d ago

Community do makerspace type jobs exist after college?

53 Upvotes

I work at my university’s makerspace and I absolutely love it. are there jobs like this in the real world?

something that would allow me to be creative and work in all areas of engineering (not just my major)? I get to operate and teach students and faculty how to use equipment in the machine shop, wood shop, electronics lab, 3D printing, laser cutting, embroidery machine, vinyl cutter, cricut, and more. I also get to help organize, market, and run large events for the campus community.

if real jobs like this exist what are some ways I can find them? like job titles to search for or companies to look at?


r/maker • • 3d ago

Showcase first time trying to laser bleach a curved denim hat, honestly surprised i didn't ruin it

Post image
9 Upvotes

Was fully expecting to scorch right through this denim cap since keeping the focus on a curved surface without a proper hat jig is usually a nightmare. Stuffed a rolled-up towel tight inside the crown to flatten it out and ran a low-power pass on my aliencell laser just to see if it would bleach the indigo dye instead of burning the cotton.

Somehow it actually worked lol. The faded texture came out a little more uneven than I expected, but the fabric survived, so I'll take that as a win for a first attempt.

Still figuring out the best way to keep curved hats at a consistent height without a proper jig.


r/maker • • 4d ago

Showcase I made a marionette as a housewarming present for a friend

Thumbnail
gallery
8 Upvotes

Inspired by Pelham Puppets, I made a marionette of a clown character she designed


r/maker • • 4d ago

Inquiry Ideas or fun stuff I can do with this audio equipment?

Thumbnail
gallery
4 Upvotes

I'm looking for something to do with this equipment I got for free. I think it all works, but I don't have a need for a concert at my house lol.

Do you have an idea? Can I use them as is for something? Can I repurpose it for something? Can I take it apart to create something useful with the components? Can I make art? A science experiment? Anything other than setting it on the curb?

Appreciate your help. And feel free to suggest other subs if appropriate.

Thanks!


r/maker • • 5d ago

Multi-Discipline Project I engineered an open-architecture industrial linear actuator. I'm open-sourcing the full CAD, BOM, and PDF build guide.

301 Upvotes

The Problem: Commercial high-torque linear actuators are often closed-box, impossible to repair, or prohibitively expensive. I wanted precision, variable stroke control, and full modularity.

The Build: I engineered this around NEMA high-torque steppers, MGN12H rails (250 mm), and an ESP32 controller. The biggest challenge was getting the structural rigidity right without making it impossible to assemble at home. I ended up designing custom jigs to align everything perfectly.

The Specs:

  • Variable stroke control
  • Industrial-grade linear motion components
  • Fully modular design

Open Source Files: I want to keep this technology accessible, so I’ve documented everything. You can grab the complete STEP files, DXFs, the Bill of Materials, and my full PDF builder's guide here:https://lm42p.com/diy

Let me know if you have any questions about the kinematics or the Next.js/Vercel setup I used to host the docs—happy to talk shop!


r/maker • • 4d ago

Showcase Open Sourced the Animatronic Eye (link in the comments)

Post image
5 Upvotes

r/maker • • 4d ago

Help Hello, I want to build a cyberdeck.

0 Upvotes

Hello, I want to ask for some detailed advice on how to create a cyberdeck. I've watched videos before but I really don't know how, any advice is appreciated.

Edit: Thank you to those who gave their insights, I'll look into it, thank you again!


r/maker • • 4d ago

Community I Built My Own DIY High-Pressure Mist Cooling System! 💧

Post image
0 Upvotes

I created an affordable home mist cooling system using a high-pressure pump and SwitchBot automation.

It produces ultra-fine mist that evaporates quickly, helping cool the surrounding air through evaporative cooling.

What do you think of this DIY project? I'd love to hear your feedback!

https://youtu.be/LP7bv_mWxpU


r/maker • • 6d ago

Showcase We Made a Charmander Diorama… with REAL Rain!

Thumbnail
gallery
27 Upvotes

Hi, guys! :)

There’s a scene in Pokémon where Charmander looks so sad out in the rain, and we wanted to make our own little version of it. Then we thought, what if we made it rain for real?

We modeled, 3D-printed and painted the diorama, then built a water circuit to make the rain fall and a small LED circuit to light up the scene. That’s how our little diorama ended up being a working fountain.

What do you think of how the rain effect turned out?


r/maker • • 7d ago

Help Feedback requested: second prototype of my 3D-printed, battery-powered espresso machine

Thumbnail
gallery
11 Upvotes

Hi all. I’m a product designer from Italy. My first portable espresso machine was my university thesis: Open Sorso, 3D-printed with a manual syringe pump. It’s shared under CC BY-NC-SA. This is the second prototype, Briù. It’s still a rough prototype, and I’d love feedback from people who build things.

The build

  • Shell: 3D-printed in PETG
  • Power: 3S 18650 pack with a BMS
  • Brain: an ESP32-S3, with an MP1584 buck converter giving 5 V to the logic and the LEDs
  • Heater and pump: switched by MOSFET modules. The heater is ON/OFF, the 12 V pump runs on PWM, and an NTC reads the temperature.
  • Interface: one button and 3 WS2812B LEDs. Double click to heat, long press to brew.
  • Coffee: ESE pods. It heats 35–40 ml to 85–90 °C in about 7 minutes (I measured with a thermometer and a stopwatch).

A friend handled the electronics. I did the design and the printed parts.

What I learned the hard way

  1. PETG vs heat. I took it out on a boat. In direct sun, the shell near the heater partly deformed inward.
  2. Tank fitting. I made a barb from a PP medical syringe and glued it into a ~1.5 mm hole with silicone. In a cold test it came off. My backup plan is a brass barb.
  3. Printed channels have a downside. The water path from the pump to the pod is printed into one part, so there’s nowhere to fit a pressure gauge. Pressure is unmeasured, and the coffee is good but has no crema.
  4. Standby drain. When it sits unused, the battery is flat in 2–3 days. The current wiring wasn’t designed for low power.

Next step: a custom PCB with proper MOSFETs, a thermal fuse that works independently of the firmware, and USB-C PD charging for the 3S pack.

What I’d love your input on

  • Materials near the heater: what would you print parts near a hot boiler in? ASA, PC, PP, or would you design them out of the print entirely?
  • Water fittings in printed parts: what has worked reliably for you? Brass heat-set barbs, threaded inserts, something else?
  • Testing points: how would you design in a test point for a pressure gauge without adding a leak point?
  • If it were released one day: what would you actually want, and in what form? STEP files, STLs, firmware, a PCB, a BOM, a kit?

It’s not for sale and the files for this version aren’t released yet. Happy to share more photos and details in the comments.

You can follow the project on insta (sorso.of.coffee) or www.sorsoofcoffee.it


r/maker • • 7d ago

Help Non-Stick thermal pad?

Thumbnail
gallery
8 Upvotes

Have a cheap crappy USB Peltier mini fridge to keep a small amount of milk cool for tea and coffee.

Peltier module works fine, but the bottles I have, have bugger all contact area. Any ideas on some kind of non-stick thermal pad or gel I could put down to increase thermal conductivity between the bottle and the peltier module, so it's not trying to conduct through air?

Maybe some kind of oil or wax pad I could put in?


r/maker • • 7d ago

Showcase I made a humanoid for fun

Post image
16 Upvotes