r/MechanicAdvice • • 4h ago

Ok, now I’m seriously confused

Thumbnail
gallery
25 Upvotes

Battery is draining overnight.

2 possibilities: bad battery, parasitic draw.

  1. Bad battery

N.B. I don’t drive often, once a week (please read on as I feel like this is not the issue)

I bought a charger, charged the battery up to 12.5-12.6 (smart charger shuts off then and goes into maintenance). At 8A it charged 12.2 -> 12.6 in less than 2 hours. Yes, another sign of a bad battery as this should take longer. Car drained to 12.15 overnight.

Next day: charged again (for 6h), disconnected the battery. 10h later, car was at 12.56…. Ok maybe not the battery?

2. Parasitic draw

As seen above, I’m drawing 0-0.02A. I set this up, locked the car and left it for ~30 mins. It was at 2.5A when locked and eventually tethered off, exactly what should happen.

I’m now out of ideas. It’s a 12V calcium 65Ah battery I bought new last year (15 months). I’ve been struggling with no start for a few months. I fixed an evap issue but this was a secondary issue. It’s now gotten so bad I need a jump after 1-2 days, whereas I didn’t before.

Possible the battery has just suffered from serious sulfation and it is in fact bad? I’ve hooked up my Topdon tester and the smart charger, they say it’s fine, just low.

2015 1.6L ford fiesta ST EU model


r/MechanicAdvice • • 54m ago

Rotor won’t sit properly

Thumbnail
gallery
11 Upvotes

Replacing the wheel bearings and rotor on my 04 2wd xlt ranger but I notice the rotor isn’t going all the way onto the spindle like I’ve seen in other videos. I should have enough thread to put the washer and nut back on assuming the rotor goes all the way on.


r/MechanicAdvice • • 4h ago

Should I replace these spark plugs? Gap measured 0.045" - 2010 Tacoma 2.7 4 cyl

Post image
13 Upvotes

r/MechanicAdvice • • 1h ago

Does this look bad?

Thumbnail
gallery
6 Upvotes

Should i change the head gasket and hope for the best

1.9 TDI AHF


r/MechanicAdvice • • 38m ago

Could I replace my own alternator?

5 Upvotes

I don't use reddit much, so please remove if not allowed and sorry if it's the wrong sub or something.

I drive a 2010 Rav 4. Its a 2.5L

I was just kind of wondering if replacing it is super hard, or if I could replace it myself. I know some about cars, and know it seems super easy to do. I'm a broke college student and can't pay the $560 dollars the places around me want to replace it. I know there are videos I could follow, just wondering if it's possible for a regular girl with a few hours on her hands and some common sense can do it Lmao.

And any tips and tricks? should I just eat the cost and have someone replace it for me? I want to learn more about cars, and people say this is also an easy way to get into it.


r/MechanicAdvice • • 15h ago

Can anyone help me figure out what the issue is?

49 Upvotes

I have a beater 1986 Subaru loyale with a 2004 wrx engine swap. I was drifting around and something broke. It still engages into every gear and does the same thing no matter what gear I’m in. I think it may be the differential but I can’t tell


r/MechanicAdvice • • 22h ago

Firestone insisting I need a new control arm because of a cracked bushing

Thumbnail
gallery
172 Upvotes

Car is a 2017 VW Tiguan Limited with 91k miles, bought used in 2022. Ever since my first state inspection (back when I lived in Boston) mechanics have been mentioning a cracked bushing, but would always quote me for the full control arm, not just a bushing replacement. The photos above were taken by Firestone employees ~a year and a half apart (May 2025 on the left, November 2026 on the right. Unfortunately I cannot find any older photos.).

I don't see any difference between these two photos, but the one in 2025 was flagged as "Needs attention" and the 2026 one was flagged "Needs Repair." Here's the thing; I had one other Firestone visit between these two where Steering and Suspension weren't even flagged at all, marked as green on the inspection report. The quote I got in 2025 was for ~$1.4k.

Am I the one being ridiculous here? Those bushings have been cracked the whole time I've owned the car. I don't think they've gotten worse but without the old photos I can't be sure. I'm hoping to trade the car in sometime in the next year or so and get a Mazda CX-5. Is it worth it to get this done? I admit to knowing very little about cars so any advice is much appreciated.


r/MechanicAdvice • • 37m ago

Fuel rail pressure sensor 1.3 CDTI

3 Upvotes

Okay , so I have a Corsa D from 2008 with the 1.3 cdti engine , one day it started knocking and I tought the injectors failed but after pulling of the fuel rail pressure sensor the knocking stopped and it ran perfectly, I bought an aftermarket Magneti Mirelli brand sensor (the Bosch one was 3 times the price and I'm broke lol) and after installing the car runs absolutely fine but a check engine appeared that when read says something about fuel rail pressure communication error, also trough obd 2 the sensor gives a constant 255 bar pressure reading.

Once again car starts fine and runs well , can I somehow "teach" the car the new reference values of the sensor or should I even bother with it?


r/MechanicAdvice • • 3h ago

Looking for another opinion 03 impreza GD blob

5 Upvotes

Hit a massive fuckoff pothole at 60-70k last night and now there’s a knocking from the rear left when corning to the left.

I’ve got bc coilovers so the suspension is relatively stiff and i can only here this rythmic knocking when I’m hard corning/turning

Refer to video for the knock. My thoughts are the CV I’ll be jacking it up tomorrow to take a a look.

The video was taken at a roundabout and I’m going the opposite way of traffic flow as i wasn’t really able to replicate the noise where I was otherwise.

I don’t like knock knock jokes from my car :(


r/MechanicAdvice • • 7h ago

Is this alternator's pulley bad?

9 Upvotes

Mercedes w211 e220 CDI 2004.


r/MechanicAdvice • • 3h ago

How Much life is left on these? ML350 2008

Thumbnail
gallery
4 Upvotes

r/MechanicAdvice • • 5h ago

Cadillac software and the light of 1000 suns

5 Upvotes

So I've been a Cadillac guy for almost 20 years. 95 Eldo, 09 DTS, Escalade, CT6. Anyways, I've searched high and low for a remedy to this specific issue I'm having with my CT6 : The light of 1000 sun's. So picture this - its 430a.m., you hop into your 2018 CT6 3.0TT, she's sexy as hell. It's dark outside. Fire up the engine, and everything lights up to a nighttime dimness. The soft glow of the cue screen, faint door accent lights, the calm brightness of the cluster and the HUD projection on the windshield make it easy to see out of all the windows; even with 5% tints. So you settle in, put your hand on the shifter, and put it into reverse.... It's Hiroshima all over again. You're immediately blinded by the most piercing light you've ever seen. Visibility to the outside world is lost. No mirror, camera or window can help you. You've become so completely disoriented, effectively putting yourself into a box with no way to see out. What happened to the peaceful, calm, quiet, comfortable - almost snuggly atmosphere you were in only moments ago? Blinded by the light of 1000 sun's.

The cue screen blasts to full brightness whenever the car is put into reverse. There has to be a setting coded somewhere in the software to turn this off. I cannot find any support or direction about it though. Ford has Forscan. BMW, Audi, you can go in and change settings with a laptop. Does anyone know how to do this with GM/Cadillac??


r/MechanicAdvice • • 58m ago

What do I do???

Thumbnail reddit.com
2 Upvotes

r/MechanicAdvice • • 1h ago

Could this broken bolt be extractable? With welding ? I tried drilling into it

Thumbnail
gallery
3 Upvotes

r/MechanicAdvice • • 3h ago

Misfire on heavy load Audi A4 2014

Post image
3 Upvotes

So I have 2.0tfsi

Under heavy load it misfires

Replaced coils and spar plugs

Clean valves and intake manifold

Car runs smoothly and have 0 issues when driving normaly. Idle and moderate load it handles perfect. As soon I put pedal to the floor it stars misfireing. I checked codes and I have nothing. I don't belive that injectors are leaking. Oil smells fine no gasoline smell.

I got one mistake once (in case someone ask. I have advanced autel scanner at the shop and still show me 0 mistakes)

I cleared this and never comes back.

I replaced cooling lines, expansion tank, and pump gascets. Just to make sure I have a good pressure and the engine doesn't run overheated.

Flaps inside intake move free and i don't have a vacuum leak.


r/MechanicAdvice • • 1h ago

Cylinder head leakage at 20%

Thumbnail
gallery
2 Upvotes

Need advice. Ive never rebuilt a used head. Always assembled new heads. I have 20 percent leakage on exhaust valves which I performed with the cams out to prevent false readings. You can feel pressure coming out the downpipe. Ill post before and after pics of the exhaust seats. The before Pic is how it looked when I removed the exh valves. Second Pic is how they looked when i did a light lapping with fine grit compound to check contact pattern. Will going to a heavier grit get me an even contact pattern or will I need to absolutely take it to get machined? If so, how much will machining work cost me? Im located in milwaukee. Any advice will help. If machining isnt too far off from a new head, I will might just get me a new head. Not sure yet! Need your folks help! This is off a 2013 Mercedes Ml63.


r/MechanicAdvice • • 1h ago

Disparition liquide de refroidissement

Thumbnail reddit.com
2 Upvotes

r/MechanicAdvice • • 1h ago

Need a prt im lot able to get in europe

2 Upvotes

How can i figure out if vw usa sells specific parts?
I need an zylinder head vw t5 3.2
022103351d
022103373c
Or others would fit as well from vw golf iv or v, eos, tt, touareg
Audi also has some that would fit


r/MechanicAdvice • • 1h ago

Any idea what this noise is? 2023 Mazda CX-30

2 Upvotes

r/MechanicAdvice • • 5h ago

OEM CV axle from Toyota ($1,294) vs aftermarket from local mechanic ($842). Worth the extra $452? 2021 Highlander Hybrid, 103k mi

4 Upvotes

Hi all, I need a left front CV axle on my 2021 Highlander Hybrid (103k miles). The boot is torn and leaking grease. I'm in the Midwest and have two quotes:

- Toyota dealer: $1,294 for a genuine OEM axle

- Local independent mechanic: $842 for an aftermarket PDL axle (new).

The independent shop is also quoting the front struts with Prostrut parts, with alignment included. Their warranty is 18 months / 18k miles. The dealer's warranty on OEM parts is 12 mo / 12k miles.

Questions:

- Has anyone had good or bad luck with PDL axles on a Highlander or other Toyotas? Any vibration, clicking, or early failures?

- Is OEM worth about $450 more for a CV axle, or are good aftermarket axles fine these days?

- Anything I should ask the shop before approving the work?

Thanks in advance!


r/MechanicAdvice • • 6h ago

Suzuki Swift 2014 1.2L Petrol

Post image
4 Upvotes

r/MechanicAdvice • • 6h ago

Multilink or torsion beam

Thumbnail
gallery
4 Upvotes

I have Audi a3 2016 pre facelift 2.0 tdi 110kw. My guess is this is multilink but I just want to be sure. Can someone with experience please tell me if I'm right or not.


r/MechanicAdvice • • 2h ago

4k clutch job on car I bought less than 2 months ago

2 Upvotes

So I bought a 2017 Honda Civic hatchback recently and I was driving a manual before this but this one felt off a little, I just assumed it was because it's a much newer car but I brought it in for service and mentioned it to my service advisor and they did an inspection. They tell me the rear main seal is leaking into the clutch causing some slipping they say they can save the dual mass flywheel but said it would be just under 4k.

It's not applicable to the power train warranty, they've already attempted to file a claim

Is this safe to drive until I have the money to pay and should I try to get the place I bought the car from to do the repairs or stick with the Honda dealership?


r/MechanicAdvice • • 5h ago

Snapped bolt , is this an urgent repair?

3 Upvotes

Hi all,

2021 cx5 turbo, was changing spark plugs. All went well until i was bolting everything back on, then stupid me over tightened the bolt which holds the metal
Plate on the valve cover… 😅

The top nut snapped off and left the rest of the screw in it. The metal plate has x5 8mm bolts in total holding down the metal plate. Now there is 4/5 bolts, ive observed the metal plate when the car is on and seems extremely sturdy still and does not vibrate.

Any advice, would be appreciated!