r/Multicopter • • 4d ago

Discussion The Weekly r/multicopter Discussion Thread

1 Upvotes

Welcome to the weekly r/multicopter discussion thread. Feel free to ask your questions that are too trivial for their own thread, make a suggestion on what you'd like to see here, or just say hi and talk about what you've been doing in the world of multicopters recently.

Don't forget to read the wiki, where you'll find details of suppliers, guides and other useful links.

If you want to chat, then the Discord server is located here (an invite link is here if you haven't already joined)

Old question threads can be found by searching this link.


r/Multicopter • • 5h ago

Question Followers on tik tok ?

Thumbnail reddit.com
0 Upvotes

Am I doing this right on tik tok? Keep going to 1,000 followers to go live on GAMING to show my screen recording LIVE? It shows it as a “DRAFT” when I’m done trial and error .. but not sure if i REALLY went live ..? It showed NO one seen or passed by so I assume it IS 1,000 followers.?


r/Multicopter • • 8h ago

Blood/Gore NetRunr FPV

Thumbnail
youtube.com
2 Upvotes

r/Multicopter • • 11h ago

Question Tarot 650 frame drone build for maximum flight time?

2 Upvotes

What do you think of my proposed drone? Basically, I'm looking for maximum flight time and efficiency.

  1. Tarot 650 TL65B01 framex 1 = 476g
  2. Pixhawk 6C + PM02 x 1 = 80g
  3. PDB, SwiftWing 3-6S XT60 = 25g
  4. T-Motor MN3508 KV380 x 4 = 350 g
  5. T-Motor Air 40A ESCx 4 = 104g
  6. T-Motor MF1503 (or Tarot TL100D04) x 4 = 96g
  7. Holybro M10 GPS x 1 = 35g
  8. Skydroid C14 Pro Gimbal x 1 = 210g
  9. Skydroid GR01 x 1 = 50g
  10. GenX Pro+ 6S solid state battery of 16,000mAh x 1 = 1490g
  11. Misc. (XT60/XT30, silicone wires, battery straps, microSD, M2/M3/M4 screws)= 120g (approx)

=================

Total AUW = 2,830g (approximately)

I'm hoping this drone build gives me a minimum 30minutes flight time.

If you are to build this drone, which parts would you recommend for better efficiently and increased flight time? I'm open to all kinds of suggestions starting from the frame.

PS: I understand that changing the original frame length to accommodate 17 inch props will increase flight time but I don't want to make such customization.


r/Multicopter • • 2d ago

Commercial Drone builders switching to US motors after the FCC rule: what are you using?

13 Upvotes

Asking from the robotics side. Westmag in South SF is ramping US motor production, and a few others are popping up. Has anyone actually received US-made motors yet, and how do they compare on price and performance?

I'm with Tolerance Labs (we source motors and actuators for robotics teams at tolerancelabs.ai), so I'm trying to learn what drone folks figured out first.


r/Multicopter • • 3d ago

Question DSHOT telemetry message on DJI goggles

Thumbnail reddit.com
5 Upvotes

Reposted here in the hope someone might be able to advise on a fix.


r/Multicopter • • 3d ago

Question Would you recommend buying a DJI Mini 3 or DJI Mavic 4 Pro in Hong Kong instead of the Philippines?

Thumbnail reddit.com
1 Upvotes

r/Multicopter • • 3d ago

Question Would you recommend buying a DJI Mini 3 or DJI Mavic 4 Pro in Hong Kong instead of the Philippines?

3 Upvotes

Hi everyone!

I'm from the Philippines, and I'm planning to buy either a DJI Mini 3 or a DJI Mavic 4 Pro. However, drone prices here in the Philippines are quite expensive, so I'm considering buying one in Hong Kong, where I've noticed that prices seem to be cheaper.

I'm planning to visit Hong Kong soon, and I thought it might be a good opportunity to purchase a drone while I'm there.

I have a few questions:

  1. Would you recommend buying a DJI drone in Hong Kong instead of the Philippines?
  2. Are DJI drones generally cheaper in Hong Kong, and are the savings worth it?
  3. Are there any reputable DJI stores or authorized retailers in Hong Kong that you would recommend?
  4. Would I encounter any issues with warranty coverage, repairs, or DJI Care Refresh when bringing the drone back to the Philippines?
  5. Are there any customs regulations, taxes, or restrictions I should be aware of when bringing a drone back home?
  6. Would you recommend getting the DJI Mini 3 or spending more on the DJI Mavic 4 Pro?

I'd especially appreciate advice from Filipino drone pilots or anyone who has purchased DJI drones in Hong Kong.

Thanks in advance for your recommendations!


r/Multicopter • • 4d ago

Question Can you think of any civilian uses for a fiber optic fpv drone?

Post image
46 Upvotes

r/Multicopter • • 4d ago

Question What dji drone is this

Post image
0 Upvotes

r/Multicopter • • 5d ago

Question AI or real drone show video? 🤔

Thumbnail
youtube.com
0 Upvotes

r/Multicopter • • 5d ago

Question What betaflight configuration works upgrading to new versions?

Thumbnail reddit.com
3 Upvotes

r/Multicopter • • 6d ago

Photo 4 wonders of Lower Silesia

Post image
5 Upvotes

r/Multicopter • • 6d ago

Question Would You Recommend Buying a DJI Mavic 3 in Hong Kong Instead of the Philippines?

Thumbnail reddit.com
3 Upvotes

r/Multicopter • • 6d ago

Question Why did a relatively small payload hit my inspection drone’s flight time this hard?

4 Upvotes

I normally use this drone for aerial photos and basic visual inspections. A friend recently asked me to help with a thermal inspection of the solar panels on their roof, so I swapped my usual RGB camera for a thermal camera and gimbal.

I expected to lose some flight time, but not this much. Now I’m having to swap batteries halfway through jobs I could normally finish in one go.

It’s a custom build running T-Motor U5 KV400 motors, and I originally picked the motor/prop setup around the lighter camera. Same motors, same battery, just a heavier and bulkier payload now.

The thermal job is also a lot slower, with more hovering and stopping to check things, so I’m guessing it’s not just the extra weight.

Would you start by comparing hover current between the two setups? Mostly trying to figure out whether the original motor/prop combo still makes sense before I start swapping parts.


r/Multicopter • • 6d ago

Announcement 100km+ LoRa Video System - NOW AVAILABLE FOR PRE-ORDER

Post image
9 Upvotes

By popular demand from a previous post...

LoRa Video System Pi HATs are now available for pre-order!

PRE-ORDER HERE: https://xrctechnologies.com/products/pre-order-horizon-lora-video-system-hat

IF WE GET 100 PRE-ORDERS, WE WILL GO OPEN SOURCE

There are also a few range evaluation kits in stock along with preorders for the V1 modules shipping from Slovenia in ~2 weeks: ORDER HERE: https://bpyl.si/en/order/


r/Multicopter • • 7d ago

Question Parrot Bebop 2 Power won't charge after years in storage

Thumbnail reddit.com
0 Upvotes

r/Multicopter • • 8d ago

Question need of telemetry

Post image
3 Upvotes

r/Multicopter • • 8d ago

Question Program Flash SWD pin in 4 in 1 ESC MCUs

0 Upvotes

hi,

We are designing the 4-in-1 ESC for my drone system. Here I have a question regarding code flashing and the SWD debugger pin.
For my four MCUs, how can I flash the code for each one? What is the best way to design the PCB board connection for this?.
Some designs use 4 separate SWD data and clock pins with NRST common.
Some of them using SW data, clock, NRST all 4 separate pin.

Do I need the NRST pin while programming? But actually, it's internally pulled up in all MCUs. The debugger only programs one at a time.

thanks in advance.


r/Multicopter • • 8d ago

Question Alternative to Skydroid S10?

Post image
2 Upvotes

Just a month ago these were ~$170 and now I can only find them at $350-$500 and for this low end of tech I can’t justify those prices. Anyone know of any alternatives for cheaper?


r/Multicopter • • 9d ago

Question Testing a 5 kg survey quad for back-to-back flights. What would make you extend the turnaround?

3 Upvotes

Hey folks, I’m working on a quad for repeat photo surveys of construction sites and trying to figure out a realistic turnaround between flights. “Swap the battery and go again” is currently doing a lot of work in the plan.

The build I’m looking at is roughly 5 kg all-up, including a 600 g camera and mount. T-Motor MN501-S 360KV motors, P17×5.8 props, AIR 40A ESCs and a 6S 10,000 mAh pack. The ESCs would be mounted out on the arms with airflow.

Once the basic flight tests check out, I’d like to work up to three 15-minute flights, allowing about five minutes between them for a fresh pack and checks. Same payload and route, three matched packs. Warm-weather testing would be around 30°C/86°F. Those are targets, not numbers I’ve proven yet.

I’m planning to log battery current and voltage, check vibration logs, and measure motor and ESC surface temperatures after landing and before the next takeoff. Props, motor mounts and connectors would get checked between flights too.

What would make you extend that five-minute gap? Anyone found temperatures creeping up across successive flights, or an inspection step that took longer than expected? Also curious how you measure temperatures consistently enough to compare them.

Would appreciate hearing what changed between your first successful flight and actually running several in a row. Tryna give “yeah, probably five minutes” a slightly better evidence base. Thank yall!


r/Multicopter • • 9d ago

Discussion Transmitting Video over LoRa -> 100km+ Range Possible

Post image
141 Upvotes

Been working on a project that sends FPV video over LoRa. Designed for wings, quads, etc.

This is the longest range FPV video system I've ever tested and completely beats everything in terms of range.

It's very low resolution but the specs are impressive and it's definitely usable:

- Down to 70ms latency

- Theoretical ranges of 100km+ (from initial tests)

- 30FPS video (low resolution ~240p but usable)

- 915MHz

Stay tuned for some tests.

Started a Discord for more discussion: https://discord.gg/xarVyFAzh

Legal Disclaimer

Amateur Radio Experimentation Notice: The Horizon video system is an experimental amateur radio project intended for research, development, and educational purposes. It is not a certified commercial broadcast or communications system. Operation is subject to all applicable local, national, and international radio regulations, including licensing requirements, permitted frequency allocations, transmitter power limits, and bandwidth restrictions. Users are solely responsible for ensuring that their equipment and operation comply with applicable laws and regulations. This project is provided for experimental use only and does not constitute authorization to transmit on any frequency without the appropriate privileges or permissions.


r/Multicopter • • 9d ago

Announcement New drone build coming up!!

Thumbnail reddit.com
1 Upvotes

r/Multicopter • • 9d ago

Discussion What would make Ecalc better?

0 Upvotes

I’m interested in making something better than Ecalc for multicopters.