r/SolarDIY • • 5h ago

Day 4 of keeping the house off grid on purpose

87 Upvotes

The Pentagon wants every major base able to run for 90 days on its own power. I wanted to know what one November week looks like for a regular house, so the utility main has been off since Sunday and everything runs on what we make.

Setup is 7.6kW on the roof and an Anker E10 with three batteries, basically a big solar generator wired into the panel. We're in central Indiana with a gas furnace and gas water heater, and everything else is electric.

So far:

- Sun: sunny, about 20 kWh off the roof, house used 12, battery topped off before noon

- Mon: gray most of the day, about 8 kWh, woke up Tuesday at 50%

- Tue: mostly sun, full again by 3

- Today: overcast, 67% at lunch

Overnight use surprised me. Fridge, chest freezer and router are easy. The furnace blower pulls around 400W every time it cycles, and on a 30 degree night that adds up to more than everything else combined.

Friday and Saturday are supposed to be gray, so those two days decide whether this lasts the full week or I give up and flip the main back on :)


r/SolarDIY • • 23h ago

10 years off-grid in Nigeria: My 20kWp, 57 kWh LiFePO4 Setup.

Post image
1.0k Upvotes

I started in 2016 with a 480w, 4kWh battery (FLA) system. Over the years I have gradually grown the system to what it is today. This is what runs the house with 5 Air conditioners, an electric oven, induction cooker, a deep well pump plus a pressure assist pump and 3 water heaters.

The project is called Project Anor - because why not.

It is a 48v system

35 panels, 20 kWp, across 5 arrays.

The system is designed around 2 independent Inveters:

Victron Multi RS Solar 6000 on the light loads, fed by two of the arrays

Victron MultiPlus-II 10kva on the heavy loads (ACs, water heater, kitchen)

Two SmartSolar MPPTs (250/100 and 150/100) for the other two arrays

A 2kW Deye Micro inveter running in AC coupled mode with the output of the Multiplus 2 and connected to 4 x 640w PV.

4 × 14.3 kWh LiFePO4 packs, 16S 280 Ah, 57 kWh - JK Inveter BMS

I use a DIY Victron GX based on a Raspberry Pi CM4 EMMC.

The system provides over 95% of my electricity and am essentially off the grid.

I documented every aspect of the setup to this includes Interactive schematic, the wiring and how every part of the system link together including the, battery settings and the full parts list:

https://home.anor.openculture.org.ng

Some part of the system like the Micro Inveter and AC coupling settings is yet to be documented but I would do that soon.

I also build a dashboard for the system for

Live readings:

https://rana.openculture.org.ng


r/SolarDIY • • 3h ago

If building new house would you prefer to have your solar equipment in a separate building?

8 Upvotes

I am looking at a new house with off-grid solar. I intend to also get an EV. I am curious if it would be preferable to have the solar equipment and car charger in a separate garage. I realize the risk of fire is low; however, if the cost differential is low, would this be a better option?

On edit- Tennessee.


r/SolarDIY • • 5m ago

plug in solar: is there any use in having two plug in solar micro inverters?

3 Upvotes

Like, is it safe to have two plug in inverters plugged into the same outdoor GFI outlet?


r/SolarDIY • • 44m ago

New setup

2 Upvotes

I’m building a new system full sun east-south and west .. what would you suggest for the setup … I’m using about 9 kWh a month currently, but would like to have at least 13-15 available for future use


r/SolarDIY • • 8h ago

Ran the month-by-month sun angles myself and the “tilt = your latitude” rule is leaving energy on the table. Does this match what you see in real output?

4 Upvotes

I’m a developer, not an installer, and I went down a rabbit hole doing the solar geometry math by hand to really understand panel tilt. A few things genuinely surprised me versus the rules of thumb everyone repeats:

1. The best fixed angle for annual energy is noticeably lower than your latitude. The “set tilt equal to latitude” rule is fine, but if you want max kWh over the year, the sweet spot is more like latitude × 0.76 + 3.1 once you’re above ~25° latitude. That can be 8–12° flatter than latitude. Summer days are long and the sun is high, so a flatter panel grabs more of the year.

2. Below ~25° latitude, tilt barely matters for annual energy. The difference between “optimal” and nearly flat is small. At that point the main reason to tilt at all is so rain washes dust off instead of letting it bake on. Felt counterintuitive to me until I plotted it.

3. Seasonal adjustment is mostly a two-times-a-year thing, not monthly. Going summer lat − 15 / winter lat + 15 captures almost all the gain. Chasing the angle every month is diminishing returns unless you’re off-grid and genuinely fighting for every winter watt-hour.

So my question for people who actually have panels up and monitored: does measured output line up with this, or does real life (shading, weather, snow, roof pitch you can’t change anyway) make the “optimal angle” kind of academic? Did any of you just bolt them flat to the roof and decide the few percent wasn’t worth it?


r/SolarDIY • • 18h ago

Would this work?

Post image
13 Upvotes

Looking at a setup to maximize my solar panels. By adding in a battery to Patio Solar Setup. Thoughts on why this wont work, to absorb excess panel capacity. No export to the grid. Trying to export to the battery instead of throttling the output of the panel.


r/SolarDIY • • 4h ago

Grounding and backup supply on existing solar + inverter

1 Upvotes

I am in the UK, we have a 15-panel + Solis 5kW inverter installation along with 8kWh of Pylontech batteries and it has been very good.

My question is, that when installed, the installers were scratching their head about where to put a grounding spike due to bricks laid all around the garage where the inverter lives; as I understood it without this we couldn't run our own backup power supply from the batteries + inverter if the mains was absent.

In the end it was decided to give up on the spike and the backup power, and the setup works today for everything else, including export when the mains is there.

Now though with the Government advice to prepare to be able to make it through some days off-grid, not being able to use the batteries + inverter as somewhat self-replenishing power source via the solar, becomes a major problem that's difficult to work around.

What do I need to do to retrofit a good quality Earth connection, in terms of where to get the right kind of spike / cable, and where to connect it to the inverter? How can the backup power be consumed, it's driven into the house from the inverter as usual (the inverter claims it can provide up to 5kW on "backup"... that can power, eg, the wired-in oven?), or it comes out of its own mains socket that has to be connected to the inverter?

Thanks for any advice.


r/SolarDIY • • 1d ago

My DIY Home Solar Setup: Three Controllers and a 3000W Inverter Charger

Post image
79 Upvotes

I built this system to power my household essentials, including lights, AC units, fans, refrigerators, a freezer, a microwave, and electronics.

Positive and negative bus bars keep the wiring organized and simplify connections to the charge controllers and inverter charger.

For solar charging, I use three MPPT controllers—one 100A and two 40A—connected to separate solar arrays. A 3000W pure sine wave inverter charger powers my household appliances.

Battery bank: ~12V 800Ah total capacity, connected in parallel for large current.

I’d appreciate any advice or feedback on my setup.


r/SolarDIY • • 21h ago

Small shed solar project - do these mc4 connectors to be enclosed?

Post image
9 Upvotes

Slowly dipping my toes into solar by putting a 215W panel on top of a small shed and feeding it into solar generator inside. My understanding is that these connectors are IP67 rated and relatively safe from water but i'm paranoid and would like another layer of protection from the elements. Ideas?


r/SolarDIY • • 19h ago

I live in Orlando, FL. Currently a little anxious about the possibility of losing power but my home has full solar. Are there any supplies or books I should get in case my husband and I need to convert to off-grid?

7 Upvotes

Please do not make fun of me. We have a son and I want to do everything I can to prepare just in case.


r/SolarDIY • • 1d ago

Plug in/balcony solar and utility charges

13 Upvotes

I'm in central Maryland and my utility is BGE. Maryland recently passed a law allowing plug in solar and I've set up a system. I found out BGE charges customers with plug in solar when the customers give their extra electricity back to the grid. Net metering for plug in is not allowed in Md.

  • If you have plug in, what is your experience?
  • Have you actually checked to see if your utility charges you for excess energy you give to the grid?
  • What state do you live in?
  • Who is your utility?
  • What type of meter or meter collar do you have?

r/SolarDIY • • 1d ago

Using 10AWG stranded THHN wire VS actual PV solar wire.

17 Upvotes

I have a friend that has quite a bit of stranded 10 AWG THHN wire. What are the disadvantages of using this over store bought solar PV rated wire. I understand the insulation on the PV wire is thicker and UV resistant. If the THHN was put into conduit to protect it is there anything wrong with using it? Thanks in advance!


r/SolarDIY • • 18h ago

hooking up 3 panels.

0 Upvotes

I bought several small solar panels from TEMU, two are listed at 15w the other one says it's 1,000 watt but it's not that much larger than the others reviews say that it can't produce more than about 22 Watts.

are these any good at all for charging phones etc?

can these be hooked together to go into a controller? The large one came with a little controller that appears to have USB outputs, how do I connect the panels? series? parallel?

any help is much appreciated


r/SolarDIY • • 19h ago

Power station to plug in

1 Upvotes

Are there products that take the output of a power station (like this) and use it to provide input to the house grid for plug in solar?

Obviously there's not a male to male cord that you simply plug in with some brains that limit it to 1200 W, (most common US plugin solar limit) and limit it from killing everyone but is there something out there that will mimic that function?


r/SolarDIY • • 20h ago

Judy Power box solar charging .. help?!!

1 Upvotes

I have two Judy power boxes that need charging via solar. Does anyone have a similar setup and what do you use, (including cables?) Thanks so much!


r/SolarDIY • • 1d ago

I built a tool to see your roof's solar potential in 3D. Would love your feedback!

13 Upvotes

Hey everyone!

I've been working on a little side project called Roofline360.

The idea is pretty simple. You enter an address, and it builds a 3D model of the roof with measurements like area, slope, orientation, and so on. Takes just a few seconds.

For solar planning, it also shows solar energy potential for each roof section, including sun exposure, shading simulation, and estimated energy production. It helps you see which parts of the roof would work best for solar panels.

It currently only covers the US, and there's one free measurement per month, so you can try it without paying anything.

I'd love to hear what you think and what other features would be useful for your projects.

Thanks!

I saw that the community welcomes useful tools with free options, so I thought I'd share mine here. Hope it fits the rules!


r/SolarDIY • • 1d ago

Solar controller help for Dummy

0 Upvotes

I am very new to solar. I have been using an EcoFlow power station and some panels for about six weeks now, and that part is fine. I also recently bought a free standing 48V lifepo4 battery and an MMPT controller so I can charge that battery with solar. I opened the box with the solar controller and have no idea what I'm looking at. Apparently I will need to do some cutting and connecting. I cannot find a video with the baby steps I need, including what adapters I will need in order to hook up the panels to it and it to the battery. I hope I can do any cutting on in-between cables and then insert them into my current setup, especially since I will likely be measuring 5 times and cutting two or three times. :-). If someone can direct me to a helpful video that would be fantastic. Also if there is another sub I should post to, just let me know, thanks!


r/SolarDIY • • 1d ago

NEP micro inverter

2 Upvotes

I’ve got about a dozen micro inverters to change out, how do I check to see which ones are bad in my system. I’m sure I’ll have to go through and find each one that’s bad but I don’t know how to test them.

The installer and service company went out of business and I got a box of NEP microiverters that showed up because some of the ones we have are bad.


r/SolarDIY • • 16h ago

What if I send you indoor solar cells for free, what you gonna do with that?

Post image
0 Upvotes

Hi everyone, I'm just confused with the prospect of indoor cells. It's the third-generation photovoltaic technology, not that heavy as the silicon solar panels. I know it gonna reduce the reliance on traditional dry cell(AA、AAA)\button cell(CR2032...etc)\Small-capacity lithium battery. But it shortage is quite obvious——Output power is relatively low, which cause it's limited application scenarios. We now use the cells on remote control and some IOT sensors and also some low-power devices. But what if I want to achieve more and see true large-scale applications.

Hope you can get me more ideas.


r/SolarDIY • • 22h ago

Issues with solar panels not charging my power station

Post image
0 Upvotes

I am trying to get some lighting set up in my shed. I bought a couple of led lights and a Predator 350 power station. I also bought two 100w ecoworthy solar panels. I wired the solar panels in to a 12v cigarette light adapter and used the anderson to cigaretter light cable that came with my power station to hook it up. It doesn't look like on the screen that there is any input coming in from the solar panels but when I check the anderson connector with my meter it is showing 24v. The 9w going out it's showing is just an Eero access point and a Wyze wireless plug running.

I am assuming I did something wrong, so please let me know.

Edit: IT WAS NOT PLUGGED IN ON THE FRONT. I DIDNT WANT TO CUT MY CABLES THAT CAME WITH MY POWER STATION SO I WIRED THE PANELS TO A FEMALE CIG LIGHTER SOCKET SO I COULD USE THE CAR CHARGER CABLE THAT CAME WITH MY POWER STATION TO HOOK UP THE PANELS TO THE BACK WHERE IT IS SUPPOSED TO GO. YOU CAN SEE THE LITTLE SUN ICON LIT UP BUT ZERO WATTAGE COMING IN.


r/SolarDIY • • 1d ago

EcoFlow Stream Inverter MC4 tool

1 Upvotes

Hi,

I recently bought this inverter and half of the MC4 connections I can remove using the standard MC4 connection tool, but half are narrower? What gives? Why design an inverter that requires 2 different types of tools to remove connections?

I can't just squeeze the tabs b/c the Stream has plastic blocking me from accessing the tabs with plyers. Any tips for this or what type of tool do I need?


r/SolarDIY • • 1d ago

Amazon and Ebay Solar Panels

0 Upvotes

I'm ready to expand my system a bit and am trying to weigh pro's and cons of Amazon/Ebay panels vs Name brand ones. I have some Amazon ones and theyre working great after 3 months, which I know isnt much.

Pro's of Amazon/Ebay ones:

Theyre a good bit cheaper

They can be purchased in small amounts and delivered to your door

Cons:

The "warranty" lasts only as long as the company who is selling them

Anyone have thoughts and experience to share?


r/SolarDIY • • 1d ago

Balcony solar added to existing system

12 Upvotes

Now that we are a few month in, I'd like to hear from others in the US in states that allow balcony solar how it's going. Specifically how you see usage with simultaneous systems and import/export. I understand these 2 systems will not talk to each other.

I'm in CT, we passed balcony solar recently and there are only a few options currently Hoymiles, APsystem EZ1, and Ecoflow stream and none are truly UL3700.

e.g. I have a 10.4kw system 27 panels 385watts with 7.62kw inverter and 18kWh battery, we have an average daily production and usage in the Fall/Autumn of 1100/800kWh each month or 36kWh daily average for the year per day. If I add a 1200+watt balcony solar with projected production of 2.4kw per day with an estimated annual 650-800+kWh added to my total production.

From what I have pieced together, the balcony solar will feed into the current load of the home, not recognized by the primary solar system and then what's left will feed excess to the grid. I'm still NEM 1.0

With our existing system + EV vehicle we are averaging almost Zero/Even in March each year for the payout.

The novelty of adding more solar + upgrading to a hybrid heat pump at some point in the future + adding a small hot tub for winter use. I know adding balcony solar won't eliminate any future consumption, I would like to see adding something to help offset any that I can.

Lastly, since I'm already allowed to send to the grid, would they know if I added more than 1 balcony system?


r/SolarDIY • • 1d ago

Hey guys, looking for advice

8 Upvotes

My father and I want to spend about 2k on a solar powered system in case the grid goes down. Ive been told that getting one of those pre made systems on amazon is a scam, and to assemble my own for way less money and higher performance. Could you guys point me in the right direction, hoping to assemble entirely through Amazon. Thx!