r/Triumph_Cars • u/bobsyrunkl • 17h ago
My TR3A rebuild - Part 6
galleryOnto paint
r/Triumph_Cars • u/diabetessucksnuts • 13h ago
Working on getting this ol girl running. I’ve gotten it to where I can start the engine consistently, it will idle for as long as I want, it will hold rpms and rev. I was under the impression that the choke is to be pulled out when doing a cold start then once it warms up, push the choke in. As soon as I push the choke in the motor shuts off. The choke seems extremely finicky and has to be in the exact right position otherwise the car won’t run
r/Triumph_Cars • u/Maynard078 • 1d ago
r/Triumph_Cars • u/PhillyCheese123 • 3d ago
Well, not really. There are some things to resolve: missing trim pieces, some carb tuning, brake squeaking.
She is beautiful though. A real head turner.
This summer was the first time driving her.
Edit: I want to clarify something. I did not do the restoration. It’s my father’s car and he paid a professional to do it. No less impressive but I don’t deserve any credit!
r/Triumph_Cars • u/bobsyrunkl • 6d ago
Next week on to priming of the body
r/Triumph_Cars • u/rockafirelover • 6d ago
Looking to change out the line for my oil gauge as part of my rebuild, currently has a nylon line that's at least ten years old. I've heard the hard copper lines can work harden and crack, so I would like to avoid them. Was curious if there was a stainless steel braided flex hose that someone makes for the gauge
r/Triumph_Cars • u/Decent-Echo-2636 • 11d ago
Belle miniature au 1/18
r/Triumph_Cars • u/Maynard078 • 12d ago
r/Triumph_Cars • u/Maynard078 • 12d ago
r/Triumph_Cars • u/Maynard078 • 12d ago
r/Triumph_Cars • u/0neSaltyB0i • 18d ago
Hi all,
New to classics, and Triumph cars (So please be gentle!)
I purchased a 1500 Spitfire last weekend from a forum, car drove fine on the 80 mile journey back home, even in the storm however I did notice that the shifts felt a bit stiff (I put it down to it being a classic). Parked it up and the next day went to take it out for a spin, went to put it in reverse on the drive and the shifter assembly seemed to just pop out of place under the cover and swing around loosley (Reverse was working fine the day prior but the previous owner did state he had issues finding it). I managed to pop it back in place so I still have 1-4, but now when I lift it to put it into reverse it just swings around and I can't find the gear.
Took the shifter out today to see that a plastic retaining cover has just broke, and when I tried gearshifting it without the cover on, it allows the spring to push through the metal retaining cap that holds it all in place. I am assuming this is the root cause of the issue, but cannot for the life of me find spares anywhere for this - am I completely buggered? And is this even the root cause of the issue or is there something worse awaiting me?
I did notice that the guides on the ball at the bottom look worn, could this be impacting it as well? I can always get this laser weld repaired and file it back down but wondering whether it's actually causing me an issue.
A bit sad really, bar the drive back I'm yet to be able to take her out for a drive and was hoping I'd be able to have it for at least a day without something going wrong!
(EDIT - UK based)
r/Triumph_Cars • u/Nobbey77A • 20d ago
I’m finally getting stuff back from the Trimmer with just rear quarter panels , colin finisher and the door cards to fit
r/Triumph_Cars • u/AshBooth2000 • 20d ago
Currently off the car and being cleaned. Was wondering how much these go for? From my 6 cylinder TR6, in good condition, with the favoured motorbike cap.
Thanks
r/Triumph_Cars • u/diabetessucksnuts • 23d ago
I have a 1976 spitfire 1500, I’ve gotten it to the point where I can start it consistently with some manipulation of the choke. After idling for a bit the motor will sputter out regardless of how many different choke positions I try.
The only thing that prevents it from sputtering out is if I keep my foot on the gas pedal. I can rev the car at will as long as I never completely let off the gas. I’ve had it idling for minutes at a time while maintaining 1500/2000 rpm’s. If I hold the rpm’s and let off the pedal, the motor will start to sputter, but upon pressing and holding the gas pedal the motor will stabilize and be fine.
I’ve replaced the spark plugs, coil, battery, air filter and ensured fuel is getting past the fuel pump into the carb.
I’ve not messed with or cleaned the carb.
r/Triumph_Cars • u/Aware_Moose_7727 • 24d ago
So I have a 76 tr6. I use it to get groceries and go on summer drives and just do basic normal driving only on nice days. I won't be racing it ever, rarely will have it on the hwy. But I have heard these cars roll "easily", but I actually doubt it. I think they have a low center. I have read countless forums and have heard they are basically mouse traps and actually increases the risk of a tbi if I'm not wearing a helmet. I have read that the ones used for racing are special and made in conjunction with special seats, belts, helmets etc. I used to race Subarus and know this to be true.
I was wanting to get all your opinions! Thanks in advance.
r/Triumph_Cars • u/RileyCargo42 • 25d ago
I can make out some text like: spitfire/midget (kinda rude ngl), BRITISH LEYLAND, and England.
Car is a 78' spitfire would be appreciated if someone had a picture or print out!
r/Triumph_Cars • u/Big-Peak4035 • 27d ago
Given how infamously unreliable the Triumph Stag's 3-litre V8 was, wouldn't it have been better if British Leyland had not axed the Daimler V8, which was last produced in 1969, and kept it in production for the Triumph Stag? Why was it not considered?
The 2.5 litre Daimler V8 had 140bhp - only 5 less than the Stag V8 - and was definitely more reliable. The 4.5 litre Daimler V8 with 220bhp could also have been refined and retuned and made a luxury option for the Stag, since it did well for the Daimler Majestic Major.
r/Triumph_Cars • u/Maynard078 • 28d ago
r/Triumph_Cars • u/TwoSolitudes22 • Oct 19 '26
I have a new wooden gear knob for my spitfire.
The old one I can just unscrew and it comes off, but the hole in the new one is much too small. I am assuming I just drill out some of the plastic bit around the hole of the new knob to make the hole a bit bigger and screw it on.
But best to double check in case there is some weird tool or something not obvious that I should do instead.
