r/castboolits • • Jul 11 '22

Discount Knowledge from a Community College PC Coat one year and six months Eastwood sour apple green translucent with tight group

31 Upvotes

https://www.eastwood.com/hotcoat-powder-sour-apple-translucent-green.html?gclid=Cj0KCQjw8amWBhCYARIsADqZJoXwv0Ko8VG7f4Q9sH1fZ6E7hYWlIA81266Y3MtNgjRR1uqT1omKPCkaAiv9EALw_wcB&wickedid=601685638248&wickedsource=google&wv=3.1

That’s the link to the exact product. It’s a see-through candy coat green that looks pretty cool, glows bright green under black lights, and “lasted” 1.5 years next to titegroup.

After washing and inspection on my bench at home the PC that was not in contact directly with titegroup was fine. Solid and stayed on lead, and still wants to stay on the lead. Have to scrape it off.

The stuff on the bottom in contact with titegroup is spongey and comes off easily with a needle. Stringy like one of those weird sticky gummy hands they used to sell that stretch and stick to walls leaving slick spots that your parents had to clean later.

Definitely did not stay hard, completely deteriorated. The ammo went off fine, but this may explain why I could put 2 shots dead nuts center at 25 yards, and other times it shot 2 inches low.

I would not do long term storage with titegroup. Going thorough all my PC bullets in storage and will eventually post what I find up on here.


r/castboolits • • 1d ago

Show and Tell I'm lapping a Lee 450-200 1R mold to make 45 acp rounds

Thumbnail gallery
7 Upvotes

Backstory: I want a light shooting round that looked like a traditional lead round nose 45 acp bullet for Wild Bunch 1911 shooting... On the cheap... So I figured I'd spend 50 bucks on a mold and some Brownells 800grit lapping compound to take care of the undersized driving band and bullet base. Below are the first round of results, I will do another round to finish the mold later this week.

So the ogive is the widest part and it's measuring at like .475, then the driving band is just under that at .454, and the base is undersized at .440.

I did 3 rounds of measuring, lapping, cleaning, casting, repeat. And it's a very light push through the .452 sizer, but the base is still undersized. I think I will try the linked method of knurling the base of some bullets so that lapping compound gets trapped properly. I'm considering maybe even inserting the base of the bullet backwards into the mold, that way the lapping compound doesn't take more material off the driving band and nose. I got the brownells 800grit aluminum, and it doesn't seem to be course enough to need to be that careful. It barely removed any material even after some aggressive passes. I still won't use 1500grit sandpaper, I think that'd be a bad idea, so I'll just cast a handful of bullets my next go-around and focus exclusively on the base. In the meantime, the sized bullets I checked got loaded up into some cases and I plunk tested them, and also checked how they feed from a full mag, dropping the slide. Buttery smooth, no hangups. COAL with them is 1.215. the only issue I foresee is if the top round in a mag just so happens to slide far enough forward that the bullet is riding the front end of the magwell, it will get hung up on the slide release. But if these rounds perform great after I get the mold sorted out, I'm not opposed to taking a few thou off the slide lock. It still has plenty of clearance for all of my mag followers to trip it. But one thing at a time.

Pic below of the bullets, and the wear marks is from cycling them over and over; pistol is Auto Ordnance M1911A1.


r/castboolits • • 3d ago

I need help Need help with sizing and or crimping 9mm mak

2 Upvotes

A little back story. I am using 100gr Lee cast and powder coated bullets I have molded. After powder coating I size to .367. I have already fired 20 of these and got a good velocity and no pressure signs. I always seat and then crimp in separate steps.

I have them seated to coal of 764. Before using a Lee factory crimp die the cases measure .390 with a seated bullet. I am crimping them to .387. The loaded cartiges pass a plunk test and spin test in the pistol.

My Bulgarian Makarov has a .366 outside diameter and .364 groove diameter. Hence the reasoning I went with a .367 sizer.

So today I started loading up another 100. After verifying my crimp at .387 I loaded up 5 in a magazine and cycled them by hand. One of the bullets got stuck in the chamber and when ejected only the casing was extracted. I got it tapped out but now I’m second guessing and before i proceed another further I have some questions.

Do I need to size my bullets smaller?

Was I supposed to go 1 thou over the groove diameter instead of outside diameter?

Do I need to add more crimp? ( there are no signs of belling left over currently.)

Do I need to use the crimp die that came in my set as opposed to the factory crimp die?

I forgot to mention I believe my coal is correct as I could not get .980 .975 .970 to pass a plunk test/spin test with out pushing them into the chamber excessively. After that I would have to pry them out. I’ve loaded up a metric ton of Berrys 95gr and never ran into this before. And I had those loaded to max length of .980. And both projectiles are RN profiles


r/castboolits • • 4d ago

Rifle Who makes the best lead alloys?

1 Upvotes

I have had good experiences with Buffalo Arms and Rotometals

Are there any better manufacturers?


r/castboolits • • 5d ago

More tests of 46 Rimfire Extra Long.

Thumbnail gallery
11 Upvotes

r/castboolits • • 6d ago

Lee Cast Bullet Mould Question

3 Upvotes

I am thinking about purchasing the Lee 459-500-3R Double Cavity Mould. Any real-world examples of using Trail Boss in the 45/70? Any other powder suggestions. Nothing that will smack my shoulder!


r/castboolits • • 12d ago

I need help 575 500 grain mini ball casting problems

1 Upvotes

I have recently acquired a lee precision 575 diameter 500 grain mini ball mold and am having problems with it... unsure if its the mold or its me, but the diameter on most casts are too wide and slightly oval shaped.. some casts are up to a millimeter too wide in some spots.. is this due to the mold being manufactured wrong or could it be gunk or other things within the mold preventing it from closing all the way??? If that is the case what is the best way to clean it?


r/castboolits • • 15d ago

Where have all of the good powders gone?

Post image
14 Upvotes

r/castboolits • • 15d ago

For a long time, I have wanted a Ballard.

Thumbnail gallery
9 Upvotes

See text a picture #3


r/castboolits • • 16d ago

I need help Using masking tape for paper patching cast bullets

2 Upvotes

I've heard of people using masking tape as a paper patch for cast bullets

I'm looking to start paper patching for my 45-70 loads

Has anyone here tried using masking tape?


r/castboolits • • 16d ago

I need help Follow up first cast question

4 Upvotes

Alright I got my Lee 124gr TC sized to .356 after powder coating. I used Eastwood blue and they came out nice and even with great coverage. I started trying to find a max coal length with multiple different brands of brass. which seems to be 1.120” however I seem to have some bulging issues.

I should preference I only load mixed range brass. At first I thought it was a brass manufacturer issue. Specifically the three Norma cases I tried one at 1.120”, 1.11” and even one down at 1.050”. I made like 25 dummy rounds trying to figure this out with different manufacturers of brass. My “gold standard” is blazer brass as I’ve never had it do anything funny on me. So I trust when it fits or does not.

But I think I figured it out and I have bulging cases. No big deal I’ve had this happen with factory FMJs and Berrys. Hence why I bought a factory crimp die in the first place. So I ran them through a Lee factory crimp die and boom all three pass the plunk and spin test.

I’ve seen other posts on here advising NOT to use a factory crimp die for cast projectiles as it has the potential to resize not only the case but more importantly the bullet. So I’m looking for insights and experience.

My test barrels are factory Glock 19 barrel and brownells Glock 17 barrel. The brownells barrel eats pretty much everything. But the factory 19 barrel seems to be picky. I’d like to shoot my cast reloads out of both. Both barrels slug out to .356” as well.


r/castboolits • • 18d ago

I need help How to make 40-70 Sharps straight brass?

Thumbnail gallery
13 Upvotes

I just bought a Remington hepburn that is chambered in 40-70 sharps straight

Could I make brass out of 2 1/2 inch brass .410 shotshells or by cutting down 9.3x74R brass instead of fireforming 30-40 krag? Or would there be any better cartridges to start from?


r/castboolits • • 19d ago

I need help Would this be a good mold for paper patching 45-70?

Post image
7 Upvotes

Shooting out of a trapdoor rifle with a .460 bore


r/castboolits • • 21d ago

Show and Tell My 45-70 cast ammo

Post image
55 Upvotes

I don’t use Reddit much but I just found this subreddit. I probably won’t contribute much but I figured I should share my favorite load out of everything I cast.

Bullet is cast from a brass 2 cavity from accurate molds with a custom bullet I speced. I say speced but it’s basically the same shape as what garrets loads in their bfr specific 45-70 ammo. The main difference is those are 540 grains and these are more like 600 grains since it’s a touch longer by comparison. Since I cast at a bit higher lead percentage and with a gas check they come out to about 620 grains.

I load them at an upper mid range power level of 1325 fps out of a magnum research bfr.

And again, hello everyone


r/castboolits • • 21d ago

I need help How to expand 30-40 krag to 40 cal?

Thumbnail gallery
7 Upvotes

I'm looking into getting a Ballard rifle in 40-70/40-63 ballard and most of the cases that I have looked into are either impossible to find or are formed from other cartridges like 30-40 krag

I photo 3 you can see a 30-40 krag case that has been expanded to 40-70 sharps straight but how can I expand it to 40 cal?


r/castboolits • • 21d ago

I need help What are the case dimensions of the Magtech .410 2-1/2 brass shotshells?

Thumbnail gallery
2 Upvotes

Using Google it gave me the AI lookup which is usually inaccurate at best

By any chance would anyone here know the exact case dimensions?

I think that it may be a good parent case for 40-70 ballard


r/castboolits • • 22d ago

Rifle How to make 40-70 Ballard brass?

Thumbnail gallery
6 Upvotes

I'm looking to get an original ballard rifle soon but unfortunately ones in 45-70 have proven extremely difficult to find and it seems that 38-55 will not stand up to my needs for long range BPCR shooting

Would 40-70 sharps straight or 444 marlin brass be good to convert or would there be any other cartridge cases that would do better?


r/castboolits • • 24d ago

First cast follow up question

Thumbnail gallery
20 Upvotes

This might be a dumb question. But am I suppose to have a sharp end to my base or do these look fine? I am using lee lee356124 and lee36595. For reference I looked at dummy rounds video using the same mold and his look like mine so I think those are good.

However the projectiles out of the Makarov mold might not be correct. I found a reference picture online and in that picture the bases are very sharp and squared off.

All of my projectiles I’ve deamed worthy pass the weight check. And honestly I see no reason why I couldn’t use these as I just shoot for fun. But I happened to notice so I figured I asked.

If it is a fill out issue I’ll have to grab some pewter and try that maybe? I have batches of both bullets I cut the spruce fast on and some I cut the spruce slow on and I see no difference between the batches. All of my batches had plenty of lead overflow sitting on top of the mold so I don’t think that’s an issue.


r/castboolits • • 25d ago

Pistol First casts!

20 Upvotes

Long time lurker. I’ve been collecting equipment and waiting for a good time to try my hand at casting. Well last night I gave it a whirl and I’m hooked. I got back inside and now I’m looking at ordering rifles molds! I’d say 98% of them are great. I was swapping between 9mm Luger and 9mm mak. I learned I need to keep a screw driver on hand as my 9mm Luger mold spruce plate got pretty tight.

These were cast with a butane Coleman grill, stainless pot, and hand poured. I have to order powder coat next.


r/castboolits • • 25d ago

I need help Copper-plated bullets smoking

3 Upvotes

Hi everyone,
I cast my own 9mm bullets and electroplate them with copper at home. When firing them, I notice a small but clearly visible white cloud coming from the muzzle. It looks more like water vapor than typical powder smoke and dissipates quickly. There are no visible residues left on the cases, barrel, or other parts.
Here are some details about my process and observations:
I clean the bare lead bullets with hot water and baking soda for 10 minutes, followed by white vinegar and salt for 2 minutes.
I electroplate them in a bath made with demineralized water, acid, and copper sulfate.
After plating, I rinse them with tap water, dry them, and polish them in a tumbler using citric acid and dish soap, followed by another rinse.
I have tried different powders, including Vectan A1, BA 9½, and Vihtavuori N320. The smoke occurs regardless of the powder.
Factory CamPro Red copper-plated bullets fired with N320 produce little to no visible smoke.
Cleaning my homemade plated bullets with isopropyl alcohol after plating did not solve the problem.
The smoke is visible mainly near the muzzle, only when the shot is fired.
The cloud is not huge, but it is noticeable enough that other shooters have commented on it.
Has anyone experienced something similar with homemade electroplated bullets? Could residual chemicals from the plating bath or the pre-plating cleaning process cause this, or might there be another explanation?
I’m trying to understand the possible cause rather than assume it is a particular chemical or component. Any relevant experience or suggestions for safely identifying the source would be appreciated.


r/castboolits • • 29d ago

I need help Worn barrels: custom molds, paper patches, or creative sizing?

1 Upvotes

I have a beautiful example of a Spanish 1893 in 7x57 Mauser, dated 1905. As you can imagine, that barrel is worn.

I have shot the rifle after careful inspection, and didn't have any keyholes at 50 yards (shooting commercial .284 jacketed bullets). Obviously, those groups were trash, so now I'm trying to figure out how to tighten them.

Multiple barrel slugs and a chamber cast gave me the following readings:

Throat: .293

Grooves: .291

Lands: .277

I have a copy of Paul Mitchell's 'The Paper Jacket's, and realized after the first testing session that I need to tinker with it more. Bullets were Lee .278 round noses with 2 wraps of ~.004" rag paper (sized to .293 on the driving bands). I had jacket failure and a lot of leading on attempt 1, but I'm far from done experimenting with it. That being said, I'd like to have some other options on the table.

I have a Lee custom push through sizer, and bought several custom over run sizers to play with. Just for fun, I cast some 20:1 .309 150 gr Lee Soup cans, and sized them down to my throat diameter through several sizing steps. They looked like massive smooth sided wadcutters, and slid back into my dummy cases on chambering. I have not loaded any live rounds with these for obvious reasons.

Has anyone had any luck with paper patching for smokeless bottle neck cartridges?

Any recommendations on reasonably priced custom mold makers? I've been looking around, but am always open to recommendations. Powder coated, gas checked bullets look much easier than patching.


r/castboolits • • Oct 18 '26

I need help New to casting, why are my boolits coming out like this?

Thumbnail gallery
19 Upvotes

Hey all, new to casting and trying to cast some boolits for my trapdoor that I would love to try using this year for deer season and I am trying to figure out why my boolits are coming out like this. I cleaned the mold and preheated it by setting it on top of the lead pot. I also made a temp controller for the pot and had it set to 380C. The 2 pics are of the same boolits just the other side.


r/castboolits • • Oct 17 '26

Son got another one

Thumbnail gallery
92 Upvotes

Ky Youth rifle season is in session so my and my 11 year old son went the property to fill the freezer. This was shot with a Ruger American ranch Gen2 in 7.62x39 with a AB A10 silencer at 30-40 yards. Using the NOE 310-165 shallow HP powder coated with an aluminum gas check sized to .310 over 25grn Varget I call this my freedom load because it goes 1776fps, he hit a little far back for my liking but he is 11 and got excited and it did the job.


r/castboolits • • Oct 16 '26

First powder coating attempt newbie

Post image
23 Upvotes

Just sharing my experience so forgive me for my mistakes. But I picked up some 124gr Hornady 3567 cast projectiles and some Minnesota shooters supply 125 cast projectiles from a local reloading store. From my research it seems the Minnesota shooter supply is out of business which is a bummer because these are advertised as hard cast and were incredibly well casted out of the box. Hopefully I can try and find some more in the wild. Any ways I asked the old timer about the age and lube on the Hornadys and he said the were dry lubed and about 10 years old. The Minnesota projectiles had basic blue lube. I did save 5 each to test in their natural form for giggles.

I went through the process of removing the lubes by soaking them in brake cleaner and agitating them. Took about an hour? So not bad.

ADMITTEDLY I’ve read harbor freight black powder coat is less than ideal but I was excited and didn’t want to wait for a restock of red or order Eastwood does blue.

Anyways I learned a lot. And am set up for success on the next batch. Here are some of the good ones. Yes they have a thick coat but I was learning and if it seat’th thou shall yeet’th. I had some glob monsters which got thrown in the melt pile.I can’t wait to try these out. Before I forget these result are from three light coats while using a brass tumbler. I tried a #5 plastic container but it didn’t seem to work. Maybe I’ll try adding airsoft BBs?

Again not perfect but I’ve been waiting to try this process for months now and finally got around to it. And the Eastwood ford blue is on order as we speak.


r/castboolits • • Oct 15 '26

Pistol Love these little 145gr SWCs in 40 & 10mm. Accurate and using certain powders like Red Dot in 40s&w they feel softer than shooting 9mm.

Thumbnail gallery
27 Upvotes

Lee 401-145-SWC --> 5.0gr Green Dot (40s&w) 6.6gr Bullseye (10mm) Great for hunting rabbits.