r/corsetry • • 18d ago

Mod Announcement Before you post: Read the mockup advice checklist!

67 Upvotes

What makes a good mockup?

there are some non-negotiables that must be completed in order to accurately fit a mockup.

  • Mockups MUST be boned! (Bones are there to provide vertical tension on the fabric)
  • Boning channels MUST be sewn shut at top and bottom. (Not closing the channels is a frequent reason for fabric wrinkling and unclosed channels make it impossible for us to be able to tell if wrinkling is due to a pattern, grainline, or boning issue)
  • Mockups must be able to be laced shut! (It can be beneficial to create a reusable lacing placket that you can baste in your mockups for fitting)
  • Lacing panels should have flat spring steel on each side of the grommets. (this provides the support necessary for the lacing to not buckle or warp)

Fitting advice checklist

To receive the best fitting advice there are a few things we need from you!

Good clear pictures with the corset laced on**.** (you must lace the corset on. Merely holding it up to your body is useless for fitting advice.)

Use your phones camera timer or have a friend help!

photos should be taken straight on and not angled from above or below and include

  • At the very minimum:
  • Straight on front view, with arms relaxed at your sides
  • Back view that also shows the lacing panel, with arms relaxed at your sides (body straight no twisting or looking back)

    • Also helpful to include:
  • Side views with arms relaxed, neutral posture looking straight ahead
  • 3/4 views of each side
  • Close ups of any specific areas you are seeking help with.

Mockup tips and Fitting advice checklist


r/corsetry • • 3h ago

Newbie Made my first corset!

Thumbnail
gallery
29 Upvotes

I made my first corset this year for a Ren faire costume. It's an underbust corset and I made a separate bra covered in the same fabric to look like armor. Had a lot of fun doing it but it definitely needs some work 😀. One of the boning channels ripped day-of so I had to do some emergency surgery to fix it. The inside is a mess so I wear a little tube top underneath so it's not itchy. I included both wip and finished images.


r/corsetry • • 41m ago

Newbie First corset I made and I put one of the eyelet backward right at the end !

Thumbnail
gallery
3 Upvotes

Any way to fix this ?


r/corsetry • • 1d ago

Tips for improvement?

Thumbnail
gallery
229 Upvotes

I adapted the Aranea Black Sylvia corset for front lacing, changed the neckline, and added straps. I also moved the boning to the seams instead of the middle of each panel. This was my first draft before cutting into some fabric I got in Paris!

I’d love any tips for improvement folks might have before I cut into my next fabric. The top stitching is a bit wobbly and my grommets are spaced too far away from the boning I think. Also I don’t know how to stop the boning from poking through the bottom hem and making it all jagged — I’m using heavy duty zipties so maybe that is contributing. Would appreciate any feedback!


r/corsetry • • 3h ago

Corset Making Looking for a pattern

1 Upvotes

I'm looking for pattern for a historically accurate Regency Era short stays corset. But specifically for the style that wraps around. You put it on like a backwards vest, cross the ties in the back, bring them back around and tie under your bust line. Iirc, the style I'm looking for doesn't have full breast cups, but half circular ones. I just need a pattern with these features and instructions on properly sizing it.

I'm making a Regency Era dress for the new season of Bridgerton, but I want as much historical accuracy as I can get.


r/corsetry • • 1d ago

Corset Making Help Sizing and altering my first mockup

Thumbnail
gallery
118 Upvotes

Good day to you lovely folks,

I am making my first mockup of the Lilly Cupped Corset from Corsets by Caroline. I’ve started without the bust cups to get the fit right on the underbust before pursuing the hefty task of properly fitting bra cups. I am still somewhat of a beginner but I’ve been sewing off and on since I was 11(now 26)

I intend on wearing this over dresses or shirts so I’ve shared pictures of that as well as the others.

I think I need to take in the whole corset since the grommets shut closed. I’m not sure how exactly to go about this (but I can also search the sub for that particular question) I’m also thinking it may be a tad too short, I’d be interested to know thoughts on that.

There are flat steel bones in front and on either side of each set of grommets. I’ve skipped every other grommet as evenly as possible simply because I do not have proper lacing cord and a limited amount of ribbon. (Plus one ripped grommet)

Everywhere else has flat steel. The goal is to use the already-to-size pieces to add to a final garment so as not to waste.

Thank you guys for being such an awesome community and resource!


r/corsetry • • 1d ago

Newbie Mockup I’m happy with

Thumbnail
gallery
35 Upvotes

Hi. I made this from scratch. Ive had a couple of mockups already before this and there are still some obvious issues with this one.. but im already generally happy with the progress Ive made. i think there might be some fabric by the waist that i can still reduce. Not sure what i can do with the bust.. i suppose i could just add pads underneath. Would that help with the shape? There is also some wrinkling in the back and the grommet panel might be too wide so i was thinking of making the grommet panels narrower, cut a few centimeters off the outer back panels then add another panel between those (?). I used Rigilene for the boning. Appreciate any feedback!!


r/corsetry • • 1d ago

Corset Making Aranea Black Dolores - Mockup 2

Thumbnail
gallery
20 Upvotes

This is my second mock up of the aranea black dolores corset. This was my first post 1st mockup

Thank you to everyone who commented on my first post, i really appreciate it! I have made some changes based on these comments.

I am making this as a basis for a dress and skirt combo. I have coutil for the final product (this is a cotton drill) and it will have a fashion layer of satin and lace.

CHANGES MADE

  1. I took in 1/4 and inch on each side of the middle and second panels, grading down towards the waist to nip in at the bust - it appears I need to do more.
  2. I added 1cm to the top of the 4th panel to allow more room for my back skin - i think this works to some degree,and could possibly be done more.
  3. I sewed the boning channels a bit more narrow to see if it helps the fabric.

WHAT I WANT TO DO - ANY GUIDANCE APPRECIATED

  1. I want to take in the bust more as it sticks out a bit, and raise the bust line (to square it off a bit, so it doesnt dip/curve into the middle). Would taking it in from the centre be the best bet? I think 3/4 to 1in would suffice.
  2. Even out the back - I read that the back where it comes together should be even, and 1-2in apart. It kinda gapes outwards at my waist, and then is loose at the bottom (i am tying it myself) but where would it be best to square it off for an even finish?
  3. Bonding channels - i am currently using bias tape - would it be worthwhile using a larger seam allowance and sewing the channel out of the seam allowance (not sure on what the technique is called, but press the seam allowance to one side and stitching that raw edge to make the boning channel
  4. The bottom at the front pokes out and away from my body. How to i resolve this for a flatter look? Does it just need to be taken in here somewhere, or is it the boning making it stick out?

r/corsetry • • 2d ago

where to buy affordable coutil?

6 Upvotes

Hello, i am searching for weeks for affordable coutil fabric to make a corset, but i can only see options that are 40€ by meter, or options that i need to buy 50m minimum.i only need 2 meters.

Any suggestions?

thanks


r/corsetry • • 3d ago

Newbie First mockup - where to take in bust? General guidance also appreciated

Thumbnail
gallery
44 Upvotes

This is my first mock up of the Aranea Black Dolores corset.

My mock up is in a cotton drill (this particular one seems to be kinda lightweight for a drill - but it was on clearance!) I have used bias tape for the boning channels. I have coutil ready for my final version.

I intend to use this as a base for a dress, with a fashion layer of satin and lace.

TO THE QUESTION: It appears to be quite large in the bust, and doesnt give much support in this area - where is best to take it in?

Also, the fabric is warping quite a bit - am I putting too much tension on the fabric by pulling too hard? Or is this just my technique?

Any other pointers are very much appreciated - please be gentle though as this is my first attempt.

P.s i am aware i need more eyelets - I dont have many on hand at present and didn't want to make the trip to get eyelet tape today.


r/corsetry • • 3d ago

Washi tape

2 Upvotes

I was watching a Facebook reel, and the artist recommended using washi tape to help make boning channels. It sounded like brilliant advice. Have you tried this method?

They use the tape, and sew on the outside of the tape, then remove the washi. I love the idea of it seems brilliant to help sew even channels.


r/corsetry • • 4d ago

Could a corset have a pocket?

38 Upvotes

Utterly insane, I know. But I remember that my mother’s corset had a pocket. I can’t imagine how that would actually work, though. Was this childhood imagination? Is there anything that could appear like a corset pocket? And even if I did hallucinate it, is there a way to accomplish this?

This may be obvious but I would like to mention that I no longer have the garment itself, only my own corset, which has no pockets and is just (cotton) skin and bones.

Edit: SOLVED. Patterns of Fashion book has the thing I’m talking about. It all makes sense.


r/corsetry • • 5d ago

How to avoid back muscle from sticking out on a corset ?

Post image
197 Upvotes

Hi, so this is a 1870s corset draft iv just made, it seams to fit the model well and she says it feels comfortable as well, however i can’t help but notice that her back muscle are protruding at the back. I was wondering if there’s anything u can do to avoid this as im worried it’ll become an issue when u start drafting her bodice, any advice would be much appreciated!!


r/corsetry • • 5d ago

Corset Making First time making a corset

Thumbnail
gallery
25 Upvotes

Hi all! I’m super new to sewing and corsetry, but really love watching frieda lepold’s youtube videos and wanted to make a corset for myself.

So far I’ve done 4 mocks. The first one was in the wrong fabric while the others are in cotton muslin. It does stretch on the bias a bit.

I would love to hear your tips on how I could improve further my mock.


r/corsetry • • 6d ago

How to mitigate wrinkles

Thumbnail
gallery
29 Upvotes

Wondering how best to mitigate wrinkles. I did sandwich my fashion layer (silk taffeta) with the coutil. I notice when I pull vertically the wrinkles soften up a bit. Is it the grain of the fabric? I cut parallel to the selvage. Maybe tension? I know some people say don’t sandwich the fabrics and do them separately but I’ve seen nice corsets done this way.


r/corsetry • • 5d ago

Newbie SIDE laced regency/ short stays

2 Upvotes

Are there any patterns for regency stays that lace at the sides( under the arms)? Is that even structurally sound?


r/corsetry • • 6d ago

Help with dyeing!

Post image
19 Upvotes

Hello everyone! I'm hoping to diy a corset for a special performance. This is the sketch I have to far. As far as attaching the pearls/appliqués/stoning, I've done all 3 so that's in my bandwagon. I was wondering how I could change the color of the corset itself though. I've seen videos of people sewing fabric over it, but I was also considering dyeing it! However I have little sewing experience and dyeing scares me, plus I'm very picky about color. What would you guys suggest for a corset like this?

(P.S. the corset is 90% polyester)


r/corsetry • • 6d ago

Corset Making Can anything be done at this point?:(

Thumbnail
gallery
59 Upvotes

I tried my corseted bodice and I almost threw it away. So many wrinkles 😭 Can anything be done or should i just start from scratch?
The bodice structure:
lining
strength layer with boning
batting
fashion fabric


r/corsetry • • 6d ago

Corset Making Corset pattern search and sizing help

0 Upvotes

I'm hoping to make a gothic-style corset for one of my friends for Christmas this year and am concerned about it not fitting her, especially because she has a larger bust. I'm looking for suggestions on (preferably free or lower-cost) overbust corset patterns, as well as any tips that y'all may have on having the best shot of it fitting her. I've made 2 corsets before for different people, so I already have some experience with boning and all that, but I'm worried I may run into some fit issues, and I would feel awful if I gave it to her and it didn't fit 😭


r/corsetry • • 7d ago

Similar patterns to this corset or any pattern maker recommendations on Etsy etc?

Thumbnail
gallery
24 Upvotes

Hi all! Wondering if anyone has come across a pattern similar to these Seline Meisler corset shape/style?
Or can recommend a pattern maker online if not? :)
Would likely use a similar fabric to the 3rd photo, with same lace detail over the top.

My mum is skilled at sewing clothes etc/ an I used to take sewing classes, but we have never made a corset - we are planning to do some trial runs for my wedding dress - wedding in 6 months to see if we can learn/figure it out (we have a backup plan if that fails haha)

Any further video tutorial recommendations/advice would be appreciated too!


r/corsetry • • 7d ago

Corset Making Is pad stitching worth it?

2 Upvotes

I’m making an 1860s corset and am having trouble with pad stitching, it just always shows through on my fashion fabric. I thought of using fusible interfacing instead but heard it can bubble. Is it worth the hand cramps and extra week of work to pad stitch? Thing is I’m having a courthouse wedding and it’s going under my dress, so time I spend on the corset will be taken from time spent on the dress. Thankyou for any help


r/corsetry • • 8d ago

Corset Making Hook and eye vs busk

5 Upvotes

Hello! I am currently making one of my first corsets and, because of where im based in and when i need it to be ready, im unable to buy a busk. That being said, i have some hook and eye tape. Could i use that instead of a busk for a front closure without issues? Thank you


r/corsetry • • 9d ago

Corset Making Help with wrinkling.

Post image
13 Upvotes

Made my wedding dress. Ran out of time so I couldnt bias bind the edges or add padding, and did not clip the princess seam allowances, or zigzag stitch the seam allowances to prevent fraying. ​

However, I have since taken it apart and am still working on it. I added a thin layer of wool batting to the coutil, and zigzaged the seam allowances. i am about to add the fashion fabric again. ​Do you have any suggestions to help avoid the wrinkling you can see in the image? Should I mistyfuse the fashion fabric to the padding layer, or should I simply stitch it in place like I did before?

This is the first corset and first structured garment Ive ever made.


r/corsetry • • 9d ago

Seeking help adjusting my length

Thumbnail
gallery
19 Upvotes

I am making the aranea black Dolores corset, but have hit a snag. My bust to underbust has been shortened, and the length of underbust to waist, has also been shortened to accommodate my measurements. My waist to mid hip however has to be elongated by 3 1/4 inches, and I don’t know how to grade the pattern the purple circles are my measurements on this panel. 5 and 6 panels were easy, but I don’t know how to do this one