r/electrical • • 8m ago

Wiring removed from Irish home built circa 1960

Thumbnail
gallery
3 Upvotes

I purchased this house built around 1960, and a lot of the wiring was original so needed to be replaced based on the condition. I thought I'd show what it looked like for anyone interested.

I believe the original wiring is all VIR (vulcanised Indian rubber) singles with bare copper earth, which was fairly typical for the time. Lots of mould was found on the rubber insulation in the attic, and it was quite brittle at the ends - easy to pull apart with my fingers. The cables in the attic seemed to be connected with what seemed like bakelite block connectors.

The house had all BS1363 sockets, though I'm not sure any where original. Schuko or BS 546 (type D and M) were more common at the time in Ireland. Most rooms originally had one single socket (except kitchen).

In Ireland we used German style fuse boxes at the time, so this had all diazed fuses (unlike what was used in the UK). The separate 25A fuse holder was for the cooker. The house was extended in the '80s with more modern PVC twin and earth cables, and an RCD (old enough to be labelled "RCCB") and earth rod were added. At some point an electric shower was also installed with an additional 40A fused circuit (also with separate RCD).

When I first registered the electricity supply in my name it was only rated for 8 kVA maximum import (despite the 9kW shower), though I was able to upgrade to 12 kVA with no physical work necessary (the meter was modern, so the tails had probably been upgraded already).

The new wiring is all NHXMH-J low-smoke zero halogen PVC insulated and sheathed cables, with a new consumer unit with many MCBs, RCBOs, etc. (not pictured)


r/electrical • • 48m ago

Is this normal for a ground wire on a light fixture?

Thumbnail
gallery
3 Upvotes

I just purchased this sconce and have never seen a ground wire like this (fully removable from the fixture), so wanted to double check. The diagram that came with it makes it look like I’m supposed to sandwich that little loop behind the backplate with a washer, then attach it to the ground wire coming out of the junction box as normal, but does that seem correct?


r/electrical • • 53m ago

Question regarding electric motors

1 Upvotes

While fighting with a DC motor, a thought crossed my mind.

There are basically 2 types of DC motors: mechanically switched with the winding on the rotor (with permanent magnets or electromagnet as stator), and brushless motors with permanent magnet rotor, and stator winding controlled electronically.

I was wondering if there exist some kind of hybrid with permanent magnets on the rotor, winding on the stator, and a mechanical commutator on the rotor itself?

If this concept does exist, what is it called?


r/electrical • • 2h ago

MC cable through brick veneer

2 Upvotes

North Carolina USA. I'm working on retail shop buildings that have multiple tenants. The exterior of the buildings have lights in the aluminum canopies and also tenant badge signs that are are backlit. The backlit badge signs each have raceways that contain the ballast and other electrical items which are UL listed and a MC cable comes from the back which is drilled into the building through the brick veneer and ran to a junction box inside. The power for the canopy lights was installed with a bell box attached to the face of the brick veneer with a MC cable running through the brick veneer to the back of it. The bell box is watertight to the brick veneer with silicone, and from the Bell box we ran liquid tight conduit to the canopy lights. Electricals inspector has forced us to remove all MC penetrations and cut boxes into the brick veneer. In some cases this requires signs to be removed that have been installed, and a complete rework of the power for the canopy lights. My question is. Is there a code that specifically states that you cannot drill a hole in brick veneer and run a MC cable through it? His reasoning is that he believes the concrete will somehow damage the MC cable. The codes I have found from my research basically state that the MC cable needs to be protected from screws and other things but it doesn't specifically say I can't drill through a brick and install a cable through it. I have seen where MC cable cannot be embedded in concrete which means installed in a location that will have concrete poured around it. ( In these situations we would use PVC conduit of course.) I'm just seeking the truth, are we being forced to spend a lot of money and time because of an inspector's misinterpret of a code or is this legitimate?


r/electrical • • 3h ago

Electrical issue

0 Upvotes

any electrician out there
my house 40 yrs 125 amp
main circuit breaker started tripping
we dont have any new applicances

it started tripping after
our main electric meter was replaced


r/electrical • • 5h ago

What is/was this pit used for?

Thumbnail
gallery
26 Upvotes

Theres this... pit? Like 50 yards from my house. I randomly decided yo open it and see what it looks like inside. It looks like it once had mechanical stuff in it at one time. Its on the top of a hill, by a chain link fence, but nothing electrical anywhere near it. Theres a rain water resevior about 50 feet down the hill from it. Can anyone tell me what it was used for?


r/electrical • • 6h ago

I just bought this power strip its safe to use?

Post image
0 Upvotes

What is this grey thing


r/electrical • • 7h ago

Detached garage sub panel

1 Upvotes

I need to install a sub panel for my detached garage. I want at least a 100 amp panel. The problem is that the main panel is recessed half way in the wall ( main panel is outside) and I don’t have much room to run the required 1-1/4 conduit in the the panel. Any suggestions??
I can probably get away with 1 inch pvc but then I wound be able to run 100 amps on the sub panel.


r/electrical • • 9h ago

Help and advice regarding geyser

1 Upvotes

Hello, I purchased a V Guard Victo 10 storage geyser installed in bathroom in January 2024 (India) and used it from January 2024-March 2024, then November 2024 to March 2025 and has just started using it again. It comes with Titanium Vitreous enamel coating for hard water conditions, but oddly enough they don't cover any damage due to hard water.

I have a hard water supply and when I initially contacted the customer care 2 years back, the representative told me there is no harm in keeping the water supply on all the time. Also, didn't advice me to get the product serviced at regular intervals.

Recently, I have come across various reels on Instagram and posts on X to always get it serviced.

So my queries are:-

  1. Should I drain the geyser and keep it empty in seasons I don't use the geyser due to hard water?
  2. Should I get it serviced?
  3. There are these shockproof plugs that are being sold like Havells Lifesaviour Adaptors to prevent getting shocked due to current leakage. Are these legit? Should I get one installed? Or is the RCCB a better choice?

(Background: Last year I experienced slight current leakage in the taps in kitchen on 1-2 occassion while the geyser was turned on)

Thanks in advance!


r/electrical • • 12h ago

Failing hot leg?

0 Upvotes

So intermittent power outages occur here, half the house works, the other half, not. However the utility pole behind the house that has a light on it also goes out.
Single phase pot-to utility light pole-to house. When half the house is out that light also goes out.

When the outage happens I go out to check the legs on the main breaker, one side 120v other 60v. Phase to phase is roughly 170v

Now when the outage is no longer ongoing, everything checks out- 120/240. The local utility of course only comes when the outage isn’t happening so everything looks fine. Being in the trade, I know they should check connections from the pot or check hot legs on the service wire. Remember, the utility pole with a light on it (not put on by us) also goes out. However this cities spec may say it’s an electrician issue- What do I need to do to get the utility to look at it more in depth.


r/electrical • • 14h ago

Help with thrifted Christmas find

Post image
0 Upvotes

I got this tree topper while thrifting today and did not realize it came incomplete until I got home. My own googling tells me this is a 2 pin DIN plug. Any ideas on what kind of adaptor would work to make this star light up? Thanks in advance for any and all help!


r/electrical • • 14h ago

First vs Second Fix Invoice Split

2 Upvotes

tldr: what’s a normal invoice split for only completing first fix for a rewire In a tenement flat? Is it 85%+ of the total?

My partner and I live in Glasgow Scotland and we are going through a rewire and want advice.

We’re about midway between first and second fix in our 3 bed tenement flat with most of our sockets, lights and plates on but the kitchen, bathroom and one of the bedrooms needing full 2nd fix and another bedroom needing 1st fix completed (No sockets, light cables or switches in but apparently the cables are in attic).

Our agreed quote is for £11k of which we’ve already paid £5500. Our electrician is now said he needs us to pay another £4600 for first fix being mostly done. We’ve pointed out that first fix isn’t done and we’d feel more comfortable paying a smaller sum that doesn’t indicate the job is 90% done. He’s told us that 2nd fix isn’t only about 15% of the job so we need to pay the remainder or he won’t continue the work. None of this schedule was in our quote agreement. What would you do?


r/electrical • • 15h ago

Can I leave my hardwired smoke detector disconnected temporarily?

Post image
2 Upvotes

I removed my faulty hardwired smoke/CO detector, and the warranty replacement won’t arrive for 1–2 weeks. Can I leave it like this with the breaker on? Unfortunately, the breaker also controls all my upstairs lights.


r/electrical • • 15h ago

Led bulb still safe to use?

Post image
0 Upvotes

Tripod socket this was plugged into threw a spark when I switched it on and started buzzing. Bulb is still fine when I tried with another socket. Would prefer to not replace the bulb since it's so expensive


r/electrical • • 17h ago

How to tell if I have a whole house surge protector?

Post image
5 Upvotes

House was built in 24’


r/electrical • • 17h ago

Damaged power cable for laptop charger

Post image
0 Upvotes

Does anyone know how to fix this and is easy / cheap. I don't wat to buy a completely new charger for my laptop, how safe is it even if I keep using it like this?


r/electrical • • 18h ago

Powering (3~ IT) with 1~ backup

Thumbnail reddit.com
2 Upvotes

r/electrical • • 18h ago

Is this usual for an attic? First time homeowner.

Thumbnail
gallery
13 Upvotes

r/electrical • • 20h ago

Electric Sewer

464 Upvotes

r/electrical • • 20h ago

Replacing this guy tomorrow

Post image
5 Upvotes

Tomorrow will be my first time replacing a fuse panel this old. Wish me luck😂


r/electrical • • 20h ago

Battery soldering advice

Thumbnail
gallery
1 Upvotes

I've been soldering for a while, but it's my first time fixing a battery for Ryobi instruments on my own. First time was with my dad and I'm looking for advice on how to get better at this. Do you guys have any suggestions? Tan batteries are the old ones, pink ones are new


r/electrical • • 23h ago

Need advice-Ceiling fan issue

0 Upvotes

Electricians — Has anyone experienced repeated ceiling fan control board failures?
I installed four identical ceiling fans throughout my house, all in separate bedrooms, less than 4 weeks ago. Since then, three of the four fans have completely stopped working.
All four fans have constant power supplied to them and are operated exclusively by remote controls. None are controlled by wall switches which when moving into the house is a minor red flag that some wiring might be off.
When the fans fail, both the fan motor and light stop functioning entirely. From what I’ve been able to determine, the failures appear to be within the motor control boards rather than the motors themselves.
My question for anyone in the electrical industry is whether this sounds like a common manufacturer/control board defect or if there could be an underlying electrical issue in the house causing these repeated failures.
Three out of four fans failing in such a short period seems pretty unusual.
Has anyone encountered something similar? What would you recommend checking to determine the root cause before replacing another fan or control board?


r/electrical • • 1d ago

Should i really need to buy a cable management box? (The extension is positioned on top of the table btw from the pic)

Post image
0 Upvotes