r/fea • u/Annual_Dog_1903 • 4h ago
How to use Glue contact in PATRAN?
Hi all,
Can anyone please guide me through how to use the Glue contact in Patran? I have a bonded assembly made of 2D QUADs
Thanks!
r/fea • u/Annual_Dog_1903 • 4h ago
Hi all,
Can anyone please guide me through how to use the Glue contact in Patran? I have a bonded assembly made of 2D QUADs
Thanks!
r/fea • u/iamapieceofcheese • 1d ago
Hi everyone,
I’m working on an FEA project simulating axial compression of a bone in Prepomax. My background is in medicine rather than engineering, so I’m learning FEA as I go and have hit a wall trying to get reliable results.
My geometry is a 3D bone model segmented directly from CT data. To simulate the load, I’m applying a concentrated force to a reference point constrained to the contact surface at the end of the bone. I've tried the following so far:
I have a couple of questions I would like to ask too:
Any advice on how to properly set up this boundary condition or clean up the post-processing would be hugely appreciated. Thanks in advance!
r/fea • u/Simone190178 • 1d ago
Hi everyone,
I am performing a FEM analysis of a punch made of Uddeholm Vanadis 23 (60 HRC), which develops a crack during operation.
The analysis is currently purely elastic (linear elastic FEM).
I have attached:
The six stress components obtained from the FEM analysis at that point are:
I have also examined the material datasheet. It provides two relevant properties:
I have two main questions:
1. What is the most likely failure mechanism in this situation?
Since the normal stresses are predominantly compressive, I understand that pure compression does not cause crack opening. Therefore, I am wondering whether shear stress could be the main factor responsible for crack initiation.
Would it be reasonable to investigate a shear-dominated failure mechanism, or could the high compressive stresses themselves cause local crushing and subsequent cracking?
2. Which material strength should I use for the failure assessment?
If shear is the dominant failure mechanism, which reference strength should I use?
I would appreciate any suggestions on the correct approach, especially considering that Vanadis 23 is a high-hardness powder metallurgy tool steel and that The analysis is currently purely elastic (linear elastic FEM). The punch is subjected to a static load during operation; the load is not cyclic, so fatigue is not considered as the failure mechanism.
Thank you in advance for your help!
r/fea • u/Economy-Might9344 • 1d ago
Hello I'm a mechanical engineer working in the aerospace sector in Italy as a structural analysis and simulation engineer.
I have 3 years of experience with Abaqus doing linear/nonlinear analysis, Static and Dynamic simulations for metals and composites.
I'm currently looking for a job.
I would appreciate any help even if it was a freelancing opportunity.
r/fea • u/Theycallmetymm • 3d ago
Hey everyone. Im professional FEA analyst and there are some things i realized that are not given proper attention, or acknowledged but are indeed important.
One of such things is contact stresses. Things is, either its conformal or non-conformal, contact region exhibit very high stress gradients, which can not be resolved by any means using standard meshing resolutions accepted in the industry. And once you go that small in element sizes, no way you gonna meet deadlines. Some of my static analyses take weeks on HPC, without even such fine elements. Im excluding specific submodeling techniques..
Still, i see some of analysts try to make a judgement from contact patch stresses by using element masking. Thats a nonsense! Your element size is like 10 times larger than theoritical contact patch itself. Im not going into theoritical contact mechanics and things like fretting but %99 of time contact area outputs in fea are worthless.
In plain planar contact cases, edges are singularity zones and once you add fillets, in order to capture stress gradient, you have to mesh with literally sandgrains which has no place in industry apart from some high end niche r&d teams and startups.
Thats why simple bearing calculations like F/A still used widely by many designcodes. Because thats what is most efficient.
Whats your methods and approach in this regard? Would like to hear.
r/fea • u/imitation_squash_pro • 5d ago
I get so annoyed if I see someone present results that are only accurate with an order of magnitude as "26.64434" . The person instantly loses all credibility. It tells me they have no idea the bigger picture of what they are doing. Furthermore, too many significant digits are confusing for the eye to read and process.
I think I learned in Engineering 101 never to do this. But seems too many people out there do this in Fea world. Why?
r/fea • u/DiverHistorical5872 • 4d ago
Hi! I’m trying to find some stresses relating to anchor bolts so I’ve been using the foundation fixture feature but anytime I try to run the simulation, it won’t finish. Any advice?
r/fea • u/Natural_Ad_3366 • 7d ago





Hello. I have an assignment where I need to analyse the stress across this part. T2 is 0C and T1 is 18C. Env temp 5C. Both ends are fixed supports and cannot move. Now, I’m having an issue where no matter how fine I make the mesh at the “neck” of the part, the maximum von-mises stress and maximum normal stress continues to change significantly. For example:
gen element size=0.12mm , body sizing =0.01 (rad 0.4) : max equiv stress= 21.899, max norm stress= 23.078
stress= 23.078gen element size=0.12mm , body sizing =0.008 (rad 0.4) : max equiv stress= 23.009, max norm stress= 24.487
gen element size=0.12mm , body sizing=0.006 (rad 0.4) : max equiv stress= 23.095, max norm stress= 23.649
gen element size=0.12mm , body sizing =0.004 (rad 0.4) : max equiv stress= 24.173, max norm stress= 25.657
element size=0.12mm , body sizing =0.003 (rad 0.4) : max equiv stress= 25.486, max norm stress= 27.366
As you can see, these are not slight differences ; e.g. in the last two meshes, maximum normal stress jumps from 25.657MPa to 27.366MPa despite the extremely fine mesh (0.003 element size at the neck). This shows I don’t have convergence yet.
AI seems to believe that I have an error in my geometry, which I have checked many times to ensure that it is exact and the fillet circle is exactly tangential to both straight sides. In my last pic I have kinda shown that my geometry is exact although I couldn't figure out how to display the sketch in Spaceclaim to completly prove that but trust me on this.
Setup details:
Modelled in 2D using axisymmetric 2D behaviour to make it a cylinder.
Instead of making both ends fixed supports, I put displacements on both edges, setting Y displacement to 0 and letting it free in X (since making them fixed supports was making the ends “bulge” and making it so that the max stresses were occurring at the end corners, which isn’t correct because my brief specifically says that the ends cannot move at all).
I’d appreciate it if someone could help me figure out why the max stress isn’t evening out. Thank you
Edit: Sorted. I needed to use an edge sizing with capture curvature instead of sphere of influence because apparently sphere of influence doesn't capture curves accurately.
r/fea • u/Time_Army8340 • 7d ago
As part of my PhD research, I am building on the research of Dowell on the aeroelastic behavior of plates. Goal would be to see how thermal loads, deformations, material constraints and abnormal environments affect plate divergence, flutter behaviors. Primarily looking at ROM based approaches to model and study these phenomena.
Using the Galerkin method with basis functions is easy with simply supported boundary conditions, but in complex set of BC's (CCFF, CFCF etc), how do you build the basis functions? What is your convergence criteria for these functions? As in what variables apart from displacement?
Also, at what point do you pivot from these reduced methods to traditional FEM and solving the plate equation directly?
r/fea • u/popboogie567 • 8d ago
Hi all. Over the past month I've been building OxiPhys, a free desktop tool for static, modal, buckling, thermal and flow analysis.
To be upfront: it's free to use (including commercially) but not open source (It took awhile to build, test and debug it, I have used AI for coding, makes life easier). I do not have a Mac or Windows based system and that's why I've focused on validation:
- Plate with a hole: Kt = 3.0018 (Quad9) vs exact 3
- Cantilever modes: within 0.11% of beam theory
- Linear buckling: within 0.01% of Euler
- Cylinder flow, Re 100: drag within 0.5%
It's still single-threaded, with no shells or beams yet.
I'd love to know what breaks, and which benchmarks you'd want to see next.
Download: https://oxiphys.com
Bugs: beta@oxiphys.com
r/fea • u/nikoscham • 8d ago
Hey everyone,
More than a year ago I shared FEAScript here, my open-source finite element library written in JavaScript that runs directly in the browser. You gave me great feedback back then (and even some contributors!), so I wanted to share how it’s going.
A lot has changed since then:
Check the website: https://feascript.com/
I also made something a bit different: Tri’s Lab. It’s a small interactive lab where you solve FEM “missions” in the browser, guided by Tri, a little triangle robot 😁 The idea is to learn FEM by playing with it (no installation, nothing): lab.feascript.com
Now I’m working on 0.4.0, and the roadmap is open here: https://github.com/orgs/FEAScript/discussions/114
I’d love to hear what you think! And if anyone wants to contribute, especially on structural mechanics (I’m a chemical engineer, so heat transfer and CFD are more my thing), you’re very welcome.
The repo of the main library is here:
github.com/FEAScript/FEAScript-core
Thanks for checking it out 🤘
r/fea • u/robertrbt51991 • 9d ago
Helloo,
I wanted some document or any textbook which will give me in depth understanding about FEM Validation.(1G, Unit Displacement, Dynamic and Elasto thermic checks)
Please share if you have any documents or any textbook suggestions.
r/fea • u/No_Jellyfish7095 • 9d ago
Hi! I recently shared a video from my channel, the simulationer, here about simulating the brain, and a lot of people found it interesting! i want to thank you all for you time and hope it was useful.
I created another video about FEA validation, which I thought is a crucial step and we should give more emphasize to, here is it https://youtu.be/mwUoicZgy_Q
i would be glad to read your opinions again!
thanks
r/fea • u/Sauron_the_dead • 10d ago
As the title says I got laid off from my company last Friday. So looking for a new job.
I have 8 years of experience on LS-DYNA.
Any help would be appreciated.
I can send my resume in personal dm.
r/fea • u/TheMoodyP • 10d ago
As part of a project I'm working on at the moment I am simulating a double jointed arm with spring loaded hinges in Ansys LS-DYNA. I cant find any option for torsional springs in the interface and I'm rather stuck.
I manged to get something to work by editing the .key file before running it but to do this I had to set the hinge parts to rigid which makes the results essentially useless. I have also tried using bushing joints instead of revolute joints however this appeared to break my sim (it is possible I had them wrong though).
I was just wondering if anyone else has any experience with doing something similar and had any suggestions?
r/fea • u/FlyHot5337 • 12d ago
r/fea • u/Worldly_Reality_3950 • 12d ago
r/fea • u/Maleficent_Play1092 • 13d ago
I am looking for opinions of people who switched from abaqus CAE to hypermesh as preprocessor, for solid meshing of relatively complex plastic components. Does it accelerate your workflow?
r/fea • u/StorkieCz • 13d ago
Hello all,
Looking for people who have experience meshing solid components in both ANSA and Altair software in stress and stiffness quality. I want to see pros a cons from both and asking purely for solid components, because i believe that in shell ANSA has no competition.
Thank you
Hi everyone!
I’m learning more about physics simulation tools, particularly how AI is changing traditional FEA and thermal simulation workflows.
I’ve been reading about platforms like Vinci, Ansys SimAI, and Neural Concept, but I’d love to hear from engineers who actually work with these technologies.
A few things I’m curious about:
Which simulation tools does your team use today, and what made you choose them?
Has anyone tried Vinci or other AI-based physics simulation platforms? How do they compare with traditional solvers?
What’s the biggest bottleneck in your workflow today: setup, meshing, simulation runtime, accuracy validation, or something else?
I’m not from engineering background but curious about physics simulation models using AI.
Thanks!
r/fea • u/Worldly_Reality_3950 • 12d ago
Asked: "Static + Modal is enough, or do we need Harmonic?"'
A genius ignored the entire debate and asked: "Where did you get your damping values?"
Suddenly the question wasn't Modal vs Harmonic.
It was whether the Harmonic result would mean anything at all.