r/finishing • • 5h ago

Question Matching Stain Color

Post image
2 Upvotes

I have Diamond brand cabinets in my kitchen that were installed by the builder. These are Westburke in Buckskin color and I believe the wood is maple and birch. I custom built matching cabinets for a coffee bar, but I'm having trouble matching the stain. I've worked with Sherwin Williams over a week with four different trips and neither of their mixtures match (not even close).

I contacted the dealer that my builder used and another dealer in a nearby state. Neither dealer can tell me the details of the stain mix nor do they sell the stain other than touchup kits. I've also tried asking AI for a close formula, but that has failed also.

I understand that I won't match the color exactly, but I want close so it's not immediately noticeable. The attached photo shows my cabinets in the background. The left stain sample is the custom Minwax mix from Sherwin Williams, but it's too amber/yellow. The right sample is Minwax English Chesnutt (stain I had laying around) so everyone has a known color to reference.

Does anyone have a suggestion? I'm willing to mix my own stains or buy an off the shelf color and modify it. Thanks in advance!


r/finishing • • 8h ago

Not happy with finished result

Thumbnail
gallery
3 Upvotes

I'm back again, help me.

Photos are not the best as I'm downstairs in the basement, but I'm frustrated with this table, specifically the main (middle) section.

I have chemically stripped all pieces, sanded, cleaned off with acetone and then did 2 coats of hard wax oil.

There were dark scratches I was not able to fully get out - I am afraid to sand anymore, as well as the dark areas are bothering me too

What's my next step here? My husband has told me to leave it as it is, but I know myself and I will just stare at the imperfections and it'll drive me nuts.


r/finishing • • 6h ago

What would you finish this with?

Post image
1 Upvotes

r/finishing • • 21h ago

Question How do I fix my Bunny

Thumbnail
gallery
14 Upvotes

Hey Hey, I'm a Fashion student so don't have a ton of experience working with wood despite being a massive fan of carpentry/ artisanal furniture. I have CNC'd a bag handle out of Tulip Wood (only wood my university will CNC) and was planning to stain it walnut and finish it with linseed oil. I sanded the whole piece with 60, 80, 120 grit sandpaper before applying the finishes as planned. However after applying the stain and one coat of the oil it is looking really uneven, for context it didn't look this patchy when I tested it on a scrap or applied a bit of white spirit on the bunny to double check.

Ive been told by tutors/friends that I could pass this off as a washed out vintage look but would rather a more contemporary, uniform finish. I really like how the grain comes through and even how the stain exaggerates highlights and shadows, but there are so many points where it just looks really oversaturated (particularly the face) or streaky.

Do you have any advice on what I could do to fix the patchiness?


r/finishing • • 17h ago

Question Rubio on heavily textured wood?

Post image
3 Upvotes

Not my workpiece, but a good approximation of what I’m aiming for. Does anyone have tips for buffing the Oil Plus 2c out of something this heavily textured?

I’m thinking maybe an airway cloth buffer on an adjustable speed angle grinder, but I’m not sure that will work. I’m using Charcoal over Intense Black Precolor so hazing will definitely show. Any advice is welcome.


r/finishing • • 12h ago

Question Help with conversion varnish

1 Upvotes

I'm strictly a lacquer and pre cat lac guy . Trying out Axalta Conversion varnish . Sprayed 8oz of CV with .25 oz of catalyst and 2oz of thinner . On a test run, it was horrendous . Pure peel with light coats in turbine sprayer with 1.3 tip . Any guidance ?


r/finishing • • 12h ago

Need help with my Mexico drawer

Thumbnail
gallery
1 Upvotes

I bought a mexico style drawer which had some scratches. I got rid of the scratches by a interior wood furniture polishing paste.

But, as can be seen in the images, left some light brighter spots behind.

I looked on a Website which sell these type of furniture and bought their recommend wax finish. The wax is an non pigmented bee was with canauba. I applied the wax on these patches to try it out, but the brighter spots aren't going away.

My guess is, that the company had a colorized finish. Maybe a pigmented wax.

Have anyone a tip how to restore it?


r/finishing • • 13h ago

adding polyurethane to uv prefinished plywood edges

1 Upvotes

hi, I'm building kitchen pantry pullout drawers. I'm using prefinished plywood and would like to finish the exposed edges. What would be the easiest way to do this? Can I just spray/brush poly on the edges and whatever hits the prefinished surfaces won't stick? In the end I'd like to keep the prefinished parts unaltered. I'm doing 1/2 blind dovetails for the joints and I'd rather not have to mask everything.

Thanks!


r/finishing • • 13h ago

Need Advice What can I do to address my door?

Thumbnail
gallery
1 Upvotes

My door is getting the finish ripped off from the sun. House came with a slew of finishes in the basement so I'm a little lost on what he used on the door. I posted close up of the peeling and an area that isn't damaged.

Not sure if I have to go through and sand it all. Theres spar varnish in the basement and I know certain finishes have solvents that will redissolve a damaged top.

Any help on where to start appreciated.


r/finishing • • 1d ago

Question Advice on how to start restoring vintage furniture sewing set?

Thumbnail gallery
2 Upvotes

r/finishing • • 1d ago

Question Desk discoloration

Post image
3 Upvotes

Don't know if this belongs here sorry if it doesn't but my rubberwood desk has developed some dark color streaks on the one edge wondering what might be causing it and if there's a fix? Or i might be dumb and it's normal...

Sorry I know nothing about wood or finishing just trying to learn


r/finishing • • 1d ago

Need Advice Best stain to fix Ashley furniture table

2 Upvotes

Hey everyone, sorry if this is the wrong sub for this kind of thing. Long story short I spilled acetone on the table cloth on my Roanhowe Dining Table from Ashley furniture and it rubbed the stain off.

Wondering if someone familiar with wood stains and available colors can recommend a product I can use to help patch it up?

Product here https://www.ashleyfurniture.com/p/roanhowe_dining_table_and_4_chairs/APG-D76935-5P.html


r/finishing • • 1d ago

Wood or Veneer?

Thumbnail gallery
2 Upvotes

r/finishing • • 1d ago

Stain came out very light

Thumbnail
gallery
3 Upvotes

I am making a fort of sorts for my kids using a box that came with a pallet of equipment. I sanded that wood down with 120 grit and added a few other boards of pine (also sanded). I have some Sikkens/sico/ppg proluxe 009 dark oak stain at home which I applied to match the house and it came out just super light. I have done 2 coats and you can see the colour difference vs my actual house.

Where did I go wrong here? Any suggestions for fixing this? Or is it a sand and redo type of deal


r/finishing • • 2d ago

Need Advice Beginner here: Best cat-safe wipe-on finish for an oak branch cat tree?

Thumbnail
gallery
9 Upvotes

Hey guys, total woodworking beginner here looking for some quick advice on finishing.

A wall-mounted indoor cat tree made from 5 natural oak branches (~2.4m / 8ft long, 7–18cm thick). They’ve been dried for 1.5 years, debarked, and orbital-sanded up to P180. Because I had to grind deeper in some spots, there is visible color contrast between the pale sapwood and darker heartwood.

I want a high-quality wipe-on oil that really pops the grain, evens out the color contrast a bit, and doesn't look like plastic. Rubio Monocoat is crazy expensive here in Europe ($85 for 390ml). I'm currently looking at Osmo Polyx-Oil (Hardwax Oil) vs. Osmo TopOil, but I'm open to anything else.

Thanks for any advice, or for sharing your experience with building something like this!


r/finishing • • 1d ago

'unfinished' teak?

Thumbnail
reddit.com
1 Upvotes

r/finishing • • 2d ago

Question Heat Stain help

Post image
21 Upvotes

Someone decided to iron the tablecloth directly on the table…any tips on how to fix this finish?


r/finishing • • 1d ago

Radio and Turntable console

Post image
1 Upvotes

r/finishing • • 2d ago

Need Advice Happy with my first time doing shellac and French polishing | Any improvements for next time?

Thumbnail
gallery
17 Upvotes

Hey folks, been trying my hand at shellac on the Christmas gifts this year. Decided on French polish on this Walnut cutoff to bring out the grain depth. Used the techniques from Fabian here and I'm quite proud of the results from my first time. ​

I'm at the very final stage of wiping away the mineral oil without causing streaks and softening the coat. Bit trickier than expected and I'm doing it slowly​

I have some thoughts on how to improve for next time:

  • Don't lift the pad up when hitting the edges
  • Be aware that the shellac still can be soft, don't rest it on the finishing cones on an area within at least 12 hours
  • Don't need to use as much shellac as you think - in the words of another poster here "it should be as wet as a dog's nose"
  • Start with 1 lb cut (did so), consider the 320 grit non woven pad to cut down any grain hairs then move into 2 lb cut
  • When adding more shellac and 190 proof alcohol, don't just dip the pad into the mixture. Have a little bottle on the side and put the fluid directly into the interior cloth wad
  • Have a silicon or grippy pad when applying - don't just hold the board so you can correctly control the pressure
  • Use linen as the exterior cloth on the pad, cotton sheds too many fine hairs into the finish​
  • Even good natural hair paintbrushes are not always helpful on such a small project - they're seemingly suited for larger ones
  • You don't need to use as much fluid as you expect

Is there anything I should be doing a bit differently next time or other techniques that are good for your workflow? ​


r/finishing • • 2d ago

Need help drying finish quicker!

6 Upvotes

For the past month or so, I have been working on a wedding gift for a buddy. I just sprayed the final coat of lacquer tonight and realized that this won't be cured by the wedding. I have the wedding in 6 days and don't know how I'm going to be able to give him this without it being cured, because the way it will be packaged, there are a lot of separate small pieces that will be contacting each other. Does anyone have any previous experience with this where you found a way to dry your finish quickly or protect it somehow? I was thinking about putting a coat of wax on it the day before, but I've heard that the degassing can cause bubbles under the wax. Any advice is appreciated!


r/finishing • • 2d ago

Question Need help w topcoat :(

Thumbnail
gallery
0 Upvotes

I found this cheap sideboard on Amazon. Liked the design but not the colour. So I decided to paint it.

Started by sanding the veneer it with 80grit using my Stanley sander. I sanded enough not to show the chip wood underneath.

I then proceeded to clean the top surface with a wet microfiber cloth and applied 2 to 3 coats of green paint from Ben Moore - pictured.

I need help applying a top coat. I gathered I needed to buff up the surface with a fine grit. I don't see how I can do that without damaging the paint.

More importantly, what product would you recommend for durability and minimal stains? I want the sideboard to retain its eggshell look.


r/finishing • • 2d ago

Protect this vintage table

Thumbnail
gallery
2 Upvotes

Hi experts, I love my (wife’s) vintage table we use as our kitchen table. How can I restore/protect it? I have no desire to poly it, but I’m not sure what type of finish it might have. Should I just go paste wax? Linseed? Thanks for any input


r/finishing • • 1d ago

Question Which finish to use?

Post image
0 Upvotes

I'm trying to color a wood lamp base to match the desk visible underneath (and in the lower right). Before I try on the actual base, I did a test on scrap wood with two colors of wood stain, and while the left top is dark enough that I'd probably be happy with it, neither of the stains really show grain like the finishing on the desk does.
(I'm aware that testing on pine, I of course won't get patterning like the desk, but I expected a little more of the grain to be visible. It's also very matte.)
Am I perhaps using the wrong type of finish? Neither stain provides the gloss the desk has. I had thought it wasn't varnished, but perhaps it is. What's the right liquid for this project?


r/finishing • • 2d ago

How to finish this walnut butcher block?

Thumbnail
gallery
2 Upvotes

Got this walnut butcher block from Home Depot to make a desk for myself. Didn’t have as much dark wood in it as I was hoping. I like how the ikea karlby (pictured) in walnut is darker and more uniform but still has some contrast so that’s what I was going for.

Some reviewers that were able to achieve that finish mentioned spar urethane and tung oil. Have had mixed experience with finishes so wanted some advice before getting it wet.

Thanks all.