r/flashlight • • 12h ago Bravo

Discussion Differences in newer Wurkkos FC11Cs

Thumbnail
gallery
162 Upvotes

I recently bought a couple of FC11Cs from the Wurkkos Official Store on Aliexpress to mod and noticed that they had a couple of design differences compared to the one that I bought from Amazon during the summer.

The most significant change is in the switch. The retaining ring for the button on the new FC11C is now press fit which is disappointing. I'm not sure if the driver can be easily removed and replaced anymore since the button PCB assembly needed to be removed to push out the driver on the old version.

The new switch feels a lot more consistent and can be pressed from any point on the switch compared to only directly over the small SMD button on the old version. It's like it already has the popular FC11C button mod done to it.

The design of the driver has changed as well. The new driver has two protrusions on the PCB which probably makes it incompatible with old FC11C hosts without the cutouts for the protrusions.

The new FC11C has a longer delay from pressing the switch to the light turning on or off. It feels less responsive compared to the old FC11C. There is also an interesting quirk where trying to use moonlight mode after using turbo causes a quick bright flash before actual moonlight mode. The old FC11C does not do this.

There is also a difference in the OP reflectors. The newer one is smoother with larger "grains" compared to the old one with is less smooth and has finer "grains". I feel that the older fine grained reflector made less artifacts around the hotspot compared to the newer smoother one, but I'm not 100% sure.

The edges on the new FC11C feels sharper in the hand compared to the old FC11C. There is also a weird notch behind the front bezel which I'm not a fan of. A lot of glue was present in the threads of the bezel on the new FC11C. I had to run it on turbo to heat it up and wrap duct tape around the bezel to get enough of a grip to loosen it. I did not have to do this on the older FC11C.

Note: Ignore the beam pattern, tint, and CCT difference in the gifs. I've swapped the emitters on these lights. The orange one has a dedomed 5700k 519A with a 15 degree TIR while the black one has the stock OP reflector with a 5000k sft-25r.


r/flashlight • • 1h ago

[NLD] My first Weltool! Small but impressive!

Thumbnail
gallery
13 Upvotes

Never even had my hand on a Weltool and kinda regret it! This is a real no BS light - one level (ok, technical two, but "low" is on the fourth click, so only to preserve battery), serious throw and everything on it screams quality!

Why are there so little mentions of weltool on this sub?


r/flashlight • • 7h ago

Wurkkos TS10V3.

Thumbnail
gallery
42 Upvotes

Wurkkos TS10 V3

Disclosure. Wurkkos provided this light for review. But this is my honest opinion.

I’ve been a fan of Wurkkos for years. I really appreciate their commitment to budget-friendly, great quality lights, along with some out-of-the-box thinking here and there. The TS10 V3 is special to me, though. The TS10 V2 was my first enthusiast-level light. It’s where I first encountered Anduril 2, and I spent hours messing with it to get my head around it. It’s also the light I first burnt something with by accident. It’s where it all started for me, and I’m happy to say the new version is a huge improvement.

What’s in the box
TS10 V3
Pocket clip (installed)
14500 battery with built-in USB-C charging port
Spare O-rings
Lanyard
User manual

Build quality
As with every Wurkkos light I’ve tried, the build quality is great, especially for what I’d call budget-friendly enthusiast lights. The button is clicky and easy to find by feel on the tail. The head and tail threads are smooth and hold firm. The finish on the body feels great, and the body as a whole feels higher quality than the V2. The pocket clip is leagues above the previous version and I am thrilled about that.

Design
The V3 is more sleek and modern while keeping the classic, functional feel of the TS10. The contours of the body are more pleasing to the eye, and the new honeycomb pattern in the center adds grip while giving it a higher-end look. The reversible deep-carry pocket clip is a massive improvement. The earlier version’s clip was really bad, and this one is much, much better. It lets the light sit low in my pocket and works well. I also like the textured optic, which creates some interesting visuals from the aux LEDs on high.

UI
The UI is Anduril 2. We all know it, and we all love it. If you haven’t taken the time to learn it yet, it’s worth getting to know. It makes the TS10V3 highly customizable and unlocks so many features.

Usability
The obvious use case is a pocket EDC light. It virtually disappears in my pocket and is very comfortable to carry. It’s more than enough to quickly light up a room or a dark corner, and as part of a casual EDC kit it thrives. The V2 was about $20, and I imagine the V3 will be around that as well, making this a deal.
Edit to add it starts at $30. Copper is more obviously.

Performance
This little light punches well above its weight class. It easily lights up an entire room, or part of a pitch-black yard. The Nichia 519A emitter in the V3 has a noticeably warmer tint, (I’m guessing 5000k) than the V2’s and the V3 appears to have a high CRI. The beam is Roughly 900 lumens from a light this small is impressive, though output steps down quickly, likely due to the low thermal mass. The beam itself has a hot spot that gradually fades into useful spill. This is a very comfortable tight quarters light.

Summary
Overall, the TS10 V3 is a fantastic EDC light. Wurkkos made some great improvements on a light I already loved. The refined styling and textured optic add character, and the built-in charging on the battery adds convenience. I can see this fitting seamlessly into my EDC rotation.

Affiliate link
Check it out here via my affiliate link below.
https://wurkkos.com/?DIST=QU5OHVw%3D


r/flashlight • • 4h ago

Review [Wurkkos TS10 V3.0 - Review] (Not mine).

Thumbnail
budgetlightforum.com
19 Upvotes

I just wanted to share this review on BLF-Forum, seems of use for folks around here.

Link.

Credits/Source: Lumeniac - @ BLF-Forum.


r/flashlight • • 4h ago

Help me find another one of these lovely little AAA ligts

Thumbnail
gallery
18 Upvotes

Hi guys, I'm trying to find more of these lights but unfortunately I've had no luck.

I bought the aluminium one first from massdrop about a decade ago and a few years later I managed to find a brass one from Amazon.

For me it's the perfect AAA light, 26gr with the battery included, rear flat metal button with 3 levels with great neutral color, it is by far my most used light around the house.

Does anyone know if there is anywhere online I could pick up more ?


r/flashlight • • 3h ago

Review Nextorch HiStar headlamp review

Post image
10 Upvotes

Today I have reviewed the HiStar headlamp from Nextorch, a light offering flood, throw and red light. Could it be all the headlamp you ever need?

https://sites.google.com/view/chrisreviewsstuff/nextorch-histar


r/flashlight • • 5h ago

Low Effort Do you still use your old flashlights?

Thumbnail
gallery
13 Upvotes

Eagletac M2XC4,Nightwatch A54U2,Convoy M21K NV1010 4KK


r/flashlight • • 21h ago Bravo

LOL If NASA can’t reach Voyager 1, we will.

Thumbnail
gallery
187 Upvotes

r/flashlight • • 3h ago

Bulk keychain flashlight order

7 Upvotes

Wife is considering giving these as a gift to her co-workers.

We are looking at the lumintop frog. I think they are about 20 bucks a piece.

Can anyone point me in the direction or able to hook me up with a bulk order discount. I think we are looking for quantity of 20 or 40 pieces.

I didn’t see them on alibaba and the price on AliExpress was the same buying other places.

Does anyone have recommendations for a different but still very tiny flashlight that could be a good gift? Needs to be rechargeable, decently bright and very small.


r/flashlight • • 17h ago

Another Olight failure

Post image
71 Upvotes

The rotating ring fell off. Probably used it about one hour total.


r/flashlight • • 16h ago

Low Effort V-G-R

Post image
49 Upvotes

At dusk earlier today. Only short of about 168 septillion candelas needed to actually reach the spacecraft.


r/flashlight • • 6h ago

Review [Review] Speras TH4 - 4 colors, zoom, rotary brightness adjustment with good throw

Thumbnail
gallery
8 Upvotes

Full Review of the Speras TH4 on dahamstah.de

Max. in 1st minuteLumens at 30smax. temperatureTemp. @ 30sruntimeANSI FL1 runtimes
Speras TH4 zoomed out723 lm(454 zoomed in)686 lm50.5 °C24.6 °C3h 21min3h 21min

For the lowest values, I measured 22 lumens (unfocused) and 14 lumens (focused).

I measured 152960cd for the light, resulting in a throw of 782m – slightly more than the factory rating!

You can find the runtime graphs in the pics!

low zoomed outlow zoomed inhigh zoomed outhigh zoomed in
CCT7400K6400K7600K
CRI727073
DUV-0.0020.003-0.003

Battery charging is interesting, it pauses the charge to measure the resting voltage. Charging diagram in the pics!

Summary

The TH4 is a fascinating light. Sure, it is not a lumen monster. Aside from that, Speras got a lot right. First and foremost, every single mechanical part is machined to a really high standard. On a light where every adjustment is mechanical, that makes for great ergonomics and feel!

I was also really impressed by the UI. The combination of rotary dial and e-switch works really well for me. Brightness can be finely adjusted, even before turning the light on. Of course, you have to shift your grip to switch the light source or adjust the zoom, but both can still be done with one hand.

The performance of the light is good – in real world use, even better. In the uncooled runtime test, the light steps down after 10-15 minutes and jumps back up to full output once it cools down to just under 40°C. In the cooled runtime test, the light runs full blast without stepping down!

I can easily live with the fact that the light is not fully regulated, because sustained output would probably not be much higher with this design than it already is – and with the different LEDs, that is not easy to implement either.

Anyone looking for a fairly versatile thrower that also reaches very good distances in red and green should definitely check out Speras and take a look at the TH-series – the TH4 certainly performed well for me!

All my reviews can be found on my website.

This review can also be read and discussed at BLF and the new german TLF.


r/flashlight • • 22h ago

Low Effort NASA wants you to flash a light at the sky tonight for Voyager 1

131 Upvotes

The Voyager 1 probe is reaching one light day from earth. To celebrate, NASA wants people to shine a light and send the message VGR using morse code tonight.

I thought this sub would enjoy!

https://www.reddit.com/r/nasa/s/3x9TtfZbDB


r/flashlight • • 14h ago

Illuminated Tales This is my security night patrol combo

Post image
27 Upvotes

r/flashlight • • 39m ago

Recommendation Best compact flashlights for home use during a power outage

2 Upvotes

Hello, I’m new to this whole flashlight community and I’m looking for something that I can keep at home in the event of a blackout or power disruption. Ideally, something compact that can take AA’s but I’m open to other battery types!

I’ve noticed that the Wurkkos fc11c, Convoy T series, and Acebeam Tac 2AA get recommended somewhat often. Any advice would be greatly appreciated!

I’m hoping to not spend much more than about $50.

Thanks!


r/flashlight • • 8h ago

NLD Nitecore TINI 3 "KSA Limited Edition"

Thumbnail
gallery
7 Upvotes

Hey everyone,

Just picked up something I haven't seen discussed here — a regional run of the Nitecore TINI 3 called the "KSA Limited Edition". It was made only for Al Rimaya (الرماية), a hunting and outdoor retailer in Saudi Arabia that is also Nitecore's official distributor there.

The first thing you notice is the colour, a metallic green. The label on the back of the box just says "GREEN", and you won't find it in the standard global lineup.

On the front, the NITECORE TINI 3 branding sits at the top above the OLED screen, with the MCT mark right below it.

The back is where it gets interesting a laser engraved falcon, the Al Rimaya logo, "KSA LIMITED EDITION", and a serial number out of 2,000 Mine is 403 of 2000.

Even the manual is different It shows the green Al Rimaya version instead of the usual three-colour global lineup.

As far as I can tell, the internals and specs are identical to the regular TINI 3 so it's really a cosmetic and collectibility thing.

Curious what you all think of it Has anyone come across other regional or special editions of the TINI line?

(Note: English isn't my first language, so I used a translation tool to translate my Arabic into English please excuse any phrasing mistakes Wishing you all the best!)


r/flashlight • • 17h ago

Question How to install tritium tubes in reylight Lanapple tailcap?

Post image
36 Upvotes

Do I need to use a small amount of adhesive to keep the trits secure in the vertical tritium vial spots around the tail cap? I slid one in and it seemed like it was kind of a friction fit and somewhat difficult to tweezer back out but I’m curious to hear what others have done. I searched but haven’t found any discussion about this specific job.


r/flashlight • • 1h ago

Recommendation Need a home for CR123A

Post image
2 Upvotes

I have a set of CR123A 3V rechargeable batteries that need a flashlight home! What would you recommend?

I have mostlyEDC lights, but I don't have a selection of headlamps, so that could be an option too.


r/flashlight • • 17h ago

stumpy s7

Thumbnail
gallery
35 Upvotes

b35am 2700k. hefty little bastard.


r/flashlight • • 2h ago

Recommendation Bisycle light recommandation

2 Upvotes

Looking for a nice Bike Light.

Should have a longlife, legal easy mode but also a powerful one to flashback annoying cars and make downhill segments in the forest bright.


r/flashlight • • 3h ago

Question for modders here; are there many bodies that can be swapped with heads?

Post image
2 Upvotes

I just saw this commercial showing two different battery size and body sizes with the same flashlight head ... and it made me realize, I just bought an m21k, and I think I saw someone say it is a T8 head.

Are there alternative bodies i can use? And can I use any >20amp battery in that alternative body? (Convoy m21k/4000k nv1010)


r/flashlight • • 21h ago Popcorn

TD05 / S14 / D1 / X4 / X4Q / KR3 / FW3A / SC64W / S6 (18350) / KR1AA :)

Post image
62 Upvotes

r/flashlight • • 12h ago

Beamshot Work lights

Thumbnail
gallery
9 Upvotes

The red ones had good reviews from people in greasy rough environments like what i put my lights through so im gonna try them. The flex head sticks i bought because i like that style light for some stuff and they come with removable regular 21700 cells so thats nice. I found on amazon. Thought id share


r/flashlight • • 14h ago

Low Effort V-G-R. Doing my part.

14 Upvotes

Nealsgadget NLight L2 Pocketable LEP.


r/flashlight • • 16h ago

Beamshot Beamshot Time

Thumbnail
gallery
18 Upvotes
  1. C8+ SFT42R sorry I didn't get it up higher was distracted by a guy walking his dog.
  2. C8 XPL70.3
  3. M21H F150R 3 degree TIR optics
  4. DM11 SFT60
  5. 3X21A LHP73B
  6. KR1 SBT90.2
  7. D4V2 4x519a dedomed spot optics.

I know the 3X21A should be brighter not sure what happened there I had it on turbo.