r/handtools • • 3h ago

Tool Wall

I may seriously have too many tools. Just finished my tool wall in my new shop. Lol

149 Upvotes

18 comments sorted by

4

u/terracerrao 3h ago

Nice collection! How do you like the ECE Primus smoother?

1

u/Striking_Vehicle893 3h ago

It's a little fiddly to set up and get used to. But it works really well when you get past that. I like the lack of friction it gives and the steel is top notch.

1

u/titlecharacter 43m ago

Do you mind saying a little more about what's fiddly on setup? I'm thinking hard about pulling the trigger on one because I love my Ulmia smoother but I don't love all the hammer tapping taking up my often-limited shop time.

1

u/Striking_Vehicle893 30m ago

The lateral adjustment is very sensitive and a bit of a different style than a Stanley. Also, the adjustment knob goes through the plane and has minimal visibility if there is an issue. Mine was tough to turn easily so I had to disassemble, clean it thoroughly, and reassemble because the problem wasn't easy to see.

3

u/VarimeB 2h ago

Do you, though?

2

u/Striking_Vehicle893 2h ago

Probably not. 😂😁

2

u/Substantial-Mix-6200 3h ago

Surely there are some tools you almost never use, considering the number of saws here. It's good to have a backup! And a backup for the backup. But do you need a backup for the backup of the backup? 😂

2

u/Striking_Vehicle893 3h ago edited 1h ago

Fair point. I have a tendency to neglect saw sharpening. So I have several to cut down on frequency. Which is stupid. I should just get better at sharpening. Lol

2

u/Substantial-Mix-6200 1h ago

Not looking forward to ever having to sharpen my saws. I feel you ):

2

u/Soft_Comfortable_920 1h ago

Very good stuff. I’m in the process of setting up mine and had to take some screenshots of this.

1

u/matzederhatze 2h ago

Nice! What is that scraper plane? Do you have any Information about it? Hey do you have two Router Planes? I mean two times the Same one?

1

u/Striking_Vehicle893 2h ago

It's a Stanley 112 with an updated Hock blade. What is cool about it is that it can be used like Stanley 12 1/2 veneer scraper because you can adjust the angle any way you want or it can be used as a standard #80.

As for the router planes, I bought one when I first started. Then I realized the best bang for the buck for vintage tools and tools in general is to do auctions. So, I buy lots on auction and sometimes you get lucky. The second plane with all the attachments was one of them. Even has a 3/4" blade and I thought it maxed out at 1/2".

For most items I get that are "duplicates" I restore and sell and keep the money available for the next auction or use it for lumber or consumables.

1

u/szns4me 35m ago

How do the planes stay in the till? I’ve been scoping out different solutions for when I build one. Is there a long lip on the top block to lift up under, then place down into the bottom lip securing it from falling out?

1

u/Striking_Vehicle893 8m ago

It's at a slight incline which. Keeps it flat. Maybe 10 degrees. The bottom has no lip, but the top squares go over the very tip of the nose. Any more and it's hard to get it out. So it's pretty specific placement. Not hard to do by any stretch. But specific. Make sense?

1

u/Cooksman18 11m ago

Wait, I’m confused. Does your shop only have 1 wall? Or does it have 4 walls like most shops? Sounds like you have some work to do filling those other 3.

1

u/Striking_Vehicle893 10m ago

You know what, I hadn't considered that. I need to get back in those auction sites. 😁

2

u/therealtwomartinis 48m ago

I like the saw & file boxes, need to get off my ass and make something like that 👍