r/spacex • • 1h ago

🔧 Technical Starbase gigafactory tour

44 Upvotes

We had no fewer than three members of the r/SpaceX mod team at Starbase, TX for the Flight 15 launch and landing! u/shahar603 travelled all the way from Israel and viewed them from a boat with fellow mod u/CAM-Gerlach’s Starfleet Tours operation. u/yoweigh (me) was granted media access, including a factory tour and a special viewing area at the employee housing site approximately 4 miles east of the pad. This post is my attempt to be a journalist and report about what I learned in the factory. We’ll create a second post about the overall experience, and I'll link it here once that's a thing.

MODERATOR ADVISORY: This has been designated a technical thread. As such, we will be clamping down on the rules very hard. This thread is for technical discussion of (and speculation from) my Starfactory tour experience. If you talk about pretty much anything else, your comment will be deleted. I’ll engage with any questions y’all have for me within those constraints. The second post will likely be a party thread where you can knock yourselves out mocking our clothing choices.

We were not permitted to bring our phones into the factory, so I don’t have any pictures from this tour. There are also a few topics that I’m not able to describe in detail. For example, I’m not allowed to sketch out the factory layout from memory (yes, I asked) but I am able to give a broad description. I am, however, allowed to share a low-fidelity sketch of the super cool nosecone interior finishing jig I saw. I saw a lot of cool jigs, but that’s the only one I really geeked out over. It was a very fast-paced tour, so I wasn’t able to stop and soak in much detail until we got out to the booster megabay at the end.

The entrance to the factory looks and feels like a very futuristic office building, with high ceilings and a snazzy curvy reception area that looks like Wall-E’s girlfriend turned into a desk. Past that are the bathrooms and some office supply closets, including a merch store for employees. Beyond that begins the factory floor, which I’ll get to in a moment. From the reception area you enter the factory in the center aisle, and there’s a stairway to the left going up one level. We were taken up those stairs. From here you can access 3 stories of office space above the reception area, with lots of conference rooms and collaborative workspaces. That’s not what we’re here to tour, though.

When we reached the top of those stairs is when the tour really began. It was led by Dan Huot, SpaceX Communications Manager and frequent webcast beard guy, and Danny Fain, Senior Director of Starship Production & Engineering. I stuck with Danny for the whole tour and peppered him with questions throughout. (no offense, Dan, but he’s the factory guy at the factory tour) The whole thing felt like I was talking to someone about their Factorio game and how they planned to optimize their different science pack production lines, except his game is a lot more expensive and produces actual irl rockets. I’m pretty sure they just got a ton of white science packs with the ship return!

One of the primary goals of the Starfactory is to turn the space vehicle production line into something more akin to an automotive road vehicle production line. Tesla and SpaceX really do inform each other’s production processes. Traditional aerospace produces bespoke products. Even under a full production cadence, each unit produced is essentially a test article. This is because there is no mass production line, and individual vehicles are produced at such a slow rate that small changes are able to accumulate into large changes before they’re finished. A good example of this is how each Shuttle orbiter had its own idiosyncrasies because of the way they were designed/built.

SpaceX wants to make the Model T Ford of rockets, where the vehicles are produced so prodigiously that it magically becomes cheap.

At this point the information started flooding out more quickly than I could keep up with. The factory can currently output a ship every 2 weeks and a booster every 4. This isn’t the time it takes to build one unit; it’s the rate at which they can spit them out of the production lines. The factory itself is divided into a ship lane and a booster lane, but they’re still working to completely separate the two. Initial ring production currently happens on the booster side and that’s become a bottleneck. Danny is working to get a second ring bay setup on the ship side to eliminate that bottleneck. At that point they’ll be almost entirely separate. There’s also a wide central aisle between them for people and supplies and ship parts to move through. Throughout the tour, work had mostly stopped and they were prepping to shut down the factory for launch, so I didn’t get to see how people actually use and work with the stuff I saw.

The top of the aforementioned stairs leads to a walkway which runs along the length of the factory one story above the factory floor, offering a nice and expansive view of what’s going on below. This is the ship side, so it was difficult to see what was going on with the boosters on the other side. Both sides are divided into bays where specific processes happen and individual ships and/or ship pieces flow through to the far end, where they go to one of the two megabays outside for stacking and engine installs. (more on that later) The first 3 ship bays are nosecone metalwork and 2 ring stacking bays. Bay 2 is for stacking the first few rings. Once it gets too tall for bay 2 it’s moved to bay 3, which is setup to work on higher stuff.

The nosecones are formed in bay 1 then skip to bay 4. (I’m not sure why it’s setup that way instead of using adjacent bays) This is where I saw that super cool finishing jig, which I made a rough sketch of. It has 3 round work platforms, with the widest platform on the bottom and the narrowest up top. Internal stairways allow workers to enter from the bottom and move up to their work stations. These platforms are attached to a wide central structural cylinder that functions as a giant toolbox. Each station has the tools it needs in shadowboxed containers attached to the cylinder. There are also a bunch of other toolboxes and storage bins and lights and whatnot scattered around the platforms. All the stuff each worker needs is easily accessible to them.

An overhead crane takes the nosecone from bay 1 and plops it onto the jig in bay 4. The whole jig fills up with people outfitting the interior surface in front of them: plumbing, avionics, cabling, tankage, structural reinforcements, moar struts, whatever. I imagine that techs move around in there from station to station as their specialty is needed in a choreographed sequence, but I can’t confirm that. This is when I noticed there are caches of pre-bent piping sections scattered all over the factory, presumably for people like these techs to install in the exact place each one is needed. That stuff’s got to be a huge pain to track and manage!

At this point we were shunted somewhere else, but I’ll finish describing ship production first. After the nosecone jig comes 3 aft production bays. This is the most complex part of the vehicle, as it has to be prepared to accept engines. Next are a few final stacking and integration bays, but I couldn't see them in detail. Presumably the finished nosecones are moved there from the jig in bay 4. I had some completely incorrect speculation about HLS here, but Dan told me it was as wrong as could be. There’s something related to HLS that’s being worked on in the final bay, but it’s not an actual lander. Maybe it’s a high-fidelity cabin mockup? I just don’t know. The rest of the factory floor on the ship side is being used as a staging area for gigabay construction. We only moved off of the elevated walkway because there was nothing interesting over there for us to see.

So at this point we’re about halfway through the factory and we get shunted down to the ground floor towards the center aisle. The first thing we see at the bottom of the stairs (other than more supplies of pre-bent plumbing) is the heat shield tile application area. There was a ship in this bay being worked on, but no actual work was happening for me to observe. This was just a “wow, that’s super cool” moment and I didn’t glean much of any information from it.

Once we reached the center aisle, Danny began describing the booster production line. The two are very similar, so I think my idea of how the other side works is pretty accurate. This is where the aft production bay details came from. As previously noted, the aft section is the most complex part of the build process. In these 3 bays they integrate a TON of plumbing (so more of those pre-bent caches) and avionics and tankage and moar struts and everything needed for the aft section to accept its engines and transfer their forces to the rest of the vehicle’s structure. Individual sections have all of their integrated stuff thoroughly tested before moving to the next stage of the process. In Danny’s paraphrased words, they make sure that all of the parts of the section can talk to everything it needs to talk to. Presumably this means that they simulate the rest of the rocket and they have the section talk to that sim without knowing it’s talking to a sim. I didn’t confirm that. There are 1 or 2 final stacking bays after that.

We have now reached the far end of the factory. From here, vehicles are sent to the 2 adjacent megabays for engine installation, final stacking, and integration. Leaving the factory, the ship megabay is to your right and the booster megabay is directly in front of you. The unfinished gigabay (more on that later) is to your left. Unfortunately, the ship megabay was closed. I’ve heard that it was open for the first group that went through before ours. It must have been closed immediately after they went through. Damn you and your green sticker, u/everydayastronaut!

Anyway, the boosters move into their megabay. There are 6 bays here, with 2 on each wall. To the right are aft bays, to the left are stacked boosters. Against the back wall are 2 engine installation bays. (I’m not 100% certain about that because the bays were empty) The bays have work platforms around them connected to geared elevators. The platforms are about the size of a scissor lift’s but they’re attached to a vertical geared rail instead of the scissor thingy. Below and between the rear bays is what’s called the raptor roost. Engines move from qualification testing at McGregor into this area for final qualification and installation. I got to learn about another super cool jig here! Danny described how they were able to reduce the individual engine installation time from 8 hours to just 30 minutes. After final qualification, the engines are lifted by a crane and placed on the mobile jig. (but I’m not sure if engine install happens in the aft bays or the bays in the back by the raptor storage/qual area) The jig is moved into the engine’s precise final location underneath its assigned aft section. A lifting mechanism of some sort, maybe hydraulic, raises it until the aft section “pierces” the engine. Then they just bolt it into place and they’re done. All of the plumbing and electrical connections are made through the jig’s precise alignment.

So to summarize the megabay workflow: aft sections get final stacking and integration to the right. They get their engines, maybe in the aft bays and maybe in the back by the raptor roost, then the completed aft sections move to the left and have the rest of the booster stacked on top. Danny talked about the gigabay for a bit here. It will have 24 concurrently active work bays, meaning that it can work on 24 rockets at once. That’s 4 megabays in one building! IMO that should dispel all the rumors about Starbase being limited to development as opposed to an active operational launch site. Why would they produce so many vehicles at a site solely meant for development? It’s possible that it will be used for manufacturing process development, I suppose. They’re still going to want to use those rockets if they’re at all able to, though. That means launching them.

Think of it this way: between the two megabays they currently have 12 bays total. This setup could support at least one launch a month, with no reuse whatsoever, because that’s how long it takes to pump out boosters. With the gigabay they’d be tripling their capacity, so that means three per month with no reuse. Now factor in reuse and assign some of those bays to refurbishment. At that point they start rapidly approaching their launch cadence targets. Then KSC comes online, which could even be as soon as Q1 2027, and they’ve got a second launch site. Then in a few years Starbase LA comes online. That gives them another 10 new launch pads and a scaled up factory with dedicated fluid resource pipelines. The launch cadence is going to be absolutely insane!

Note: I’m located in New Orleans, so Starbase LA will cut my drive time to see a launch by 75%! It’ll go from 12 hours to 3 hours. I’m really looking forward to that. So FYI I’ve clearly got a bias there.


r/spacex • • 19h ago

🚀 Official SpaceX: “The Starbase tower team on location with the first caught Starship🍌”

Thumbnail
gallery
1.3k Upvotes

r/spacex • • 1d ago

Cargo Dragon NASA, SpaceX Stand Down from Dragon's Undocking on Wednesday [due to weather at splashdown site]

Thumbnail
nasa.gov
147 Upvotes

r/spacex • • 2d ago

SpaceX on X: Views from Mechazilla of the first ever Starship catch

2.2k Upvotes

r/spacex • • 3d ago

SpaceX on X: Riding on Starship 42 during final approach to catch

2.3k Upvotes

r/spacex • • 3d ago

SpaceX on X: Starship 42 coming in for catch

734 Upvotes

r/spacex • • 4d ago

Elon Musk on X: "Some phone videos I took from the tower" / X

Thumbnail x.com
381 Upvotes

r/spacex • • 4d ago

Scott Manley's review & analysis of Flight 15

Thumbnail
youtube.com
205 Upvotes

r/spacex • • 4d ago Bravo

Ship 42 returns to the tower

Post image
4.6k Upvotes

r/spacex • • 4d ago Mindblown

🚀 Official SpaceX: “Mechazilla catches Starship! Congratulations to the entire SpaceX team on this incredible achievement!”

Thumbnail x.com
2.0k Upvotes

r/spacex • • 4d ago

🚀 Official SpaceX: “Teams have polled go to return Starship to the launch site at Starbase”

Thumbnail x.com
383 Upvotes

r/spacex • • 4d ago

Starship F15 telemetry data & acceleration profiles - similar to F14, but no dip in Ship thrust at 370 s, and >40% boost, close to 4 g, for the final 30 s before SECO.

Post image
175 Upvotes

r/spacex • • 5d ago

🚀 Official SpaceX official updates on Starship Flight 15: Booster GNC automatically aborted landing, Musk says it was slightly low on fuel. “Starship coasting in orbit, still looking good for return to launch site today. Pad and tower systems are go for catch.”

Thumbnail x.com
551 Upvotes

r/spacex • • 5d ago

🚀 Official SpaceX: “Starship is now in a long coast phase around Earth. Teams will monitor Starship’s systems over the next ~21 hours that we intend to be in orbit for. We do have a few early deorbit options available should we need them, but all systems are looking good right now”

Thumbnail x.com
621 Upvotes

r/spacex • • 5d ago

Sawyer Merritt: SpaceX just officially received regulatory approval from the FAA for Starship flight 15. Launch is a go for today!

Thumbnail x.com
301 Upvotes

r/spacex • • 6d ago

🚀 Official SpaceX: “Ship 42 moves to the Starbase pad ahead of launch”

Thumbnail
gallery
853 Upvotes

r/spacex • • 8d ago

🚀 Official SpaceX: “Super Heavy moved to the launch pad at Starbase. Booster 22 is the first Super Heavy V3 booster planned to return to the launch site for catch and was used for final catch testing upon arrival, including a suspended squeeze test at catch height”

Thumbnail
gallery
795 Upvotes

r/spacex • • 9d ago

r/SpaceX Starlink 31-2 ( Flight 15) Official Launch Discussion & Updates Thread!

152 Upvotes

Welcome to the Starship Starlink 31-2 ( Flight 15) Launch Discussion & Updates Thread!

Scheduled for (UTC)Nov 13 2026, 22:45
Scheduled for (local)Nov 13 2026, 16:45 PM (CST)
Launch Window (UTC)Nov 13 2026, 22:45 - Nov 14 2026, 00:00
Weather ProbabilityUnknown
Launch siteOLPad 2, SpaceX Starbase, TX, USA.
BoosterBooster 22-1
ShipS42
Booster landingThe Super Heavy Booster 22 will attempt to return the launch site at Starbase.
Ship landingShip 42 will attempt to return to its launch site at Starbase.
Trajectory (Flight Club)2D,3D

Spacecraft Onboard

SpacecraftStarship V3
Serial NumberS42
DestinationLow Earth Orbit
Flights0
OwnerSpaceX
LandingShip 42 will attempt to return to its launch site at Starbase.
CapabilitiesMore than 100 tons to Earth orbit

Details

Third-generation second stage of the two-stage Starship super heavy-lift launch vehicle.

History

The third-generation Starship upper stage will be introduced on flight 12.

Watch the launch live

No livestreams currently available/known

Stats

☑️ 4th Starship V3 launch

☑️ 747th SpaceX launch all time

☑️ 127th SpaceX launch this year

☑️ 4th launch from OLPad 2 this year

☑️ 46 days, 9:56:01 turnaround for this pad

☑️ N/A hours since last launch of booster Booster 22

Stats include F1, F9 , FH and Starship

Timeline

TimeEvent
-0:50:00GO for Prop Load
-0:35:33Stage 1 LOX Load
-0:35:30Stage 1 LNG Load
-0:35:12Stage 2 LOX Load
-0:35:11Stage 2 LNG Load
-0:21:40Engine Chill
-0:02:50Stage 1 Propellant Load Complete
-0:02:10Stage 2 Propellant Load Complete
-0:00:30GO for Launch
-0:00:17Flame Deflector Activation
-0:00:03Ignition
0:00:00Excitement Guaranteed
0:00:00Liftoff
0:00:58Max-Q
0:02:19MECO
0:02:21Stage 2 Separation
0:02:26Booster Boostback Burn Startup
0:03:02Booster Boostback Burn Shutdown
0:06:10Stage 1 Landing Burn
0:06:35Stage 1 Landing
0:08:09SECO-1
0:26:10Orbital Insertion Burn Start
0:26:30Orbital Insertion Burn End
0:35:01Payload Deployment Sequence Start
1:17:40Payload Deployment Sequence End
1:27:46Starship Return Check
7:15:35Starship Return Check
20:41:55Starship Return Check
21:35:57Deorbit Burn Start
21:36:07Deorbit Burn End
22:10:46Atmospheric Entry
22:29:34Starship Transonic
22:30:13Starship Subsonic
22:32:16Starship Landing Burn
22:32:18Landing Flip
22:32:26Starship Landing
22:32:33Starship Landing
22:32:34Starship Catch

Updates

Time (UTC)Update
07 Nov 16:04Updated payload name.
07 Nov 15:54GO for launch, pending regulatory approval.
05 Nov 21:52NET November 13.
28 Oct 19:46NET November.
13 Sep 06:33Adding launch

Resources

Partnership with The Space Devs

Information on this thread is provided by and updated automatically using the Launch Library 2 API by The Space Devs.

Community content 🌐

LinkSource
Flight Clubu/TheVehicleDestroyer
Discord SpaceX lobbyu/SwGustav
SpaceX Nowu/bradleyjh
SpaceX Patch List

Participate in the discussion!

🥳 Launch threads are party threads, we relax the rules here. We remove low effort comments in other threads!

🔄 Please post small launch updates, discussions, and questions here, rather than as a separate post. Thanks!

💬 Please leave a comment if you discover any mistakes, or have any information.

✉️ Please send links in a private message.


r/spacex • • 10d ago

SpaceX now fundamentally an "infrastructure company," senior official says

Thumbnail
arstechnica.com
464 Upvotes

r/spacex • • 11d ago

Starship “NASA has selected @SpaceX for the Cislunar Communications Deployment Demonstration (C2D2)”

Thumbnail x.com
224 Upvotes

Full text: “A step toward keeping Moon Base connected. NASA has selected @SpaceX for the Cislunar Communications Deployment Demonstration (C2D2). Targeted for 2028, the Starship mission will demonstrate launch and spacecraft deployment capabilities that could help inform future lunar communications networks connecting astronauts, mission controllers and Moon Base.”


r/spacex • • 11d ago

r/SpaceX USSF-627 Official Launch Discussion & Updates Thread!

13 Upvotes

Welcome to the r/SpaceX USSF-627 Launch Discussion & Updates Thread!

Welcome everyone!

Scheduled for (UTC)Nov 12 2026, 04:36:30
Scheduled for (local)Nov 11 2026, 20:36:30 PM (PST)
Launch Window (UTC)Nov 12 2026, 02:35:00 - Nov 12 2026, 06:35:00
PayloadUSSF-627
CustomerUnited States Space Force
Launch Weather ForecastUnknown
Launch siteSLC-4E, Vandenberg SFB, CA, USA.
BoosterB1103-7
LandingThe Falcon 9 first stage B1103 has landed on ASDS OCISLY after its 7th flight.
Mission success criteriaSuccessful deployment of spacecrafts into orbit
Trajectory (Flight Club)2D,3D

Watch the launch live

StreamLink
Unofficial Re-streamThe Space Devs
Unofficial WebcastSpaceflight Now
Official WebcastX

Stats

☑️ 746th SpaceX launch all time

☑️ 686th Falcon Family Booster landing

☑️ 235th landing on OCISLY

☑️ 230th consecutive successful SpaceX launch (if successful)

☑️ 126th SpaceX launch this year

☑️ 70th launch from SLC-4E this year

☑️ 5 days, 3:47:48 turnaround for this pad

☑️ 32 days, 20:56:46 hours since last launch of booster B1103

Stats include F1, F9 , FH and Starship

Timeline

TimeEvent
-0:38:00GO for Prop Load
-0:35:00Prop Load
-0:35:00Stage 1 LOX Load
-0:16:00Stage 2 LOX Load
-0:07:00Engine Chill
-0:01:00Tank Press
-0:01:00Startup
-0:00:45GO for Launch
-0:00:03Ignition
0:00:00Liftoff
0:01:07Max-Q
0:02:26MECO
0:02:29Stage 2 Separation
0:02:36SES-1
0:02:58Fairing Separation
0:06:06Entry Burn Startup
0:06:30Entry Burn Shutdown
0:07:52Stage 1 Landing Burn
0:08:11Stage 1 Landing

Updates

Time (UTC)Update
12 Nov 07:02Launch success.
12 Nov 04:37Unofficial Re-stream by SPACE AFFAIRS has started
12 Nov 04:37Liftoff.
12 Nov 04:22Unofficial Re-stream by SPACE AFFAIRS has started
11 Nov 22:57Now targeting Nov 12 at 04:36 UTC
11 Nov 16:13Now targeting Nov 12 at 02:36 UTC
10 Nov 16:24Now targeting Nov 12 at 02:35 UTC
09 Nov 21:11Now targeting Nov 11 at 02:49 UTC
09 Nov 16:35Now targeting Nov 10 at 04:59 UTC
09 Nov 13:52Now targeting Nov 10 at 03:07 UTC
03 Nov 21:43GO for launch.
03 Nov 13:10Now targeting Nov 10 at 03:03 UTC
02 Nov 16:03Moved up to NET November 9 UTC.
28 Oct 18:57Liftoff.

Resources

Partnership with The Space Devs

Information on this thread is provided by and updated automatically using the Launch Library 2 API by The Space Devs.

Community content 🌐

LinkSource
Flight Clubu/TheVehicleDestroyer
Discord SpaceX lobbyu/SwGustav
SpaceX Nowu/bradleyjh
SpaceX Patch List

Participate in the discussion!

🥳 Launch threads are party threads, we relax the rules here. We remove low effort comments in other threads!

🔄 Please post small launch updates, discussions, and questions here, rather than as a separate post. Thanks!

💬 Please leave a comment if you discover any mistakes, or have any information.

✉️ Please send links in a private message.


r/spacex • • 12d ago

🚀 Official SpaceX: “RETURNING STARSHIP TO THE LAUNCH SITE”

Thumbnail
spacex.com
294 Upvotes

r/spacex • • 12d ago

🚀 Official SpaceX: STARSHIP FLIGHT 15

Thumbnail
spacex.com
428 Upvotes

r/spacex • • 12d ago

SpaceX on X: Starship is preparing for catch. Flight 15 is targeting to launch as early as Friday, November 13, pending regulatory approval

1.1k Upvotes