r/weaving • • 23h ago

Help The guild's miscommunication leads to an expensive mistake

Thumbnail
gallery
104 Upvotes

UPDATE: We took a decision for now to thread every other inch of the warp, and once the first batch is completely woven, we'll set up the second half of the warp, keeping the 12 epi and not wasting the work already done.

Thanks all for all the great questions and advices!

********

Hi weavers,

I am part of my local guild's project planning comitee and we ran into a pretty expensive pickle this week. (Apologies in advance as english isn't my first language and I'm not sure of all the technical terms)

This was supposed to be a fluffy throw blanket, in some gorgeous thick 2 ply wool. It was only dicovered after almost 3/4 of the rolling was done that the density accidentally doubled. A miscommunication happenned somewhere in the process, between the choice of the pattern, the technical adjustments, the purchase and the rolling, a project that was supposed to be 12 epi is now 24.

Given the density of the yarn, it feels like it will be impossible to weave, and will likely result in a rigid plank of wool. I even doubt the reed would accomodate two threads per dent. The issue was only raised when the team was trying to fill the last spaces and the bulging of the cramps around made it very difficult to roll the 50 ish yards as planned.

In over 100 years of combined weaving experience, this is the first time we're met with such a problem at this late of a stage, and we're not really sure how to proceed.

Suggested solutions so far:

- Try to weave it anyways as is

- Thread only every other cramp (#2, #4, #6...), following the correct threading pattern, knowing that the colours won't match. When the even cramps are empty, thread the other half (1, 3, 5...) of cramps with the same pattern, knowing again the colours won't match.

- As above, thread only the even number of cramps, but thread it 1-2-3-4 all the way and forget about the pattern or the colour position. Repeat with the uneven number of cramps.

- (the solution we're desperatly trying to avoid) Undo all the rolling done somehow, I don't know how we would keep the tension even, or if we could even hand roll all the threads individually to reset them with the correct epi... remember, over 50 yards...

- Scrap it all, eat the cost and start again.

Please let us know what you think would be the best move! Thank you so much in advance!!

Also, just so we feel less alone in this absurdity, what's the worst weaving mistake you've made?


r/weaving • • 6h ago

Work in Progress Tied on

Thumbnail
gallery
58 Upvotes

Well finished tying the warp to the apron rod. Should be able to even out the warp tomorrow morning and begin to actually weave finally. ๐Ÿ˜‚ It's a process that's for sure. In front of the reed and behind the heddles.


r/weaving • • 23h ago

Help How do you handle back pain at the loom?

11 Upvotes

I try to get up and stretch regularly, but my mid-back is really feeling the strain of working at my rigid heddle loom. I think my chair might be a little tall after I've added the tushy cushion, but does anyone have any suggestions?

I had the bright idea of putting on my corset for some extra support, but it's an underbust, so I don't get as much support higher up my back as a taller, overbust corset might give. It's not a super tight lace, so it's actually quite comfortable.

ETA: Thanks so much to everyone who responded! I put down a couple of 2x4s under my loom stand, and I'm going to switch out the dining room chair for my adjustable office chair. I also like the idea of filming how I work so I can identify where the problem areas are. Thanks again, everyone!!


r/weaving • • 5h ago

Work in Progress Tied on

Thumbnail gallery
7 Upvotes

Ready to almost start weaving.