r/FenceBuilding • • 2h ago

Did my fence contractor mess up or do it right l?

Thumbnail
gallery
1 Upvotes

This question might be obvious, I’m not sure as I have very little knowledge about construction and just hire licensed people to help me. So, thank you in advance.

I needed a fence gate post replaced, and it sits very close to the house.

When they took out the old post to put in a new one, they cut into this concrete shown in the picture. Is this the house foundation footing that they cut into, or is it just extra concrete bonded to the house foundation from the original fence post installation?

And, the second picture is after the new post installation. Is it okay for the cement to be poured directly agasint the house foundation? I ask because it seems there is a small gap between the sidewalk concrete slabs and the house foundation , but here it is not.

Thank you.


r/FenceBuilding • • 5h ago

Fake Home Depot fence

Thumbnail
gallery
18 Upvotes

My neighbors installed a Home Depot panel fence, it's fine and gets the job done (right side of photos). I decided to just match it for this small back yard area in my yard but of course their panel size didn't fit my area so I made my own version to match.


r/FenceBuilding • • 7h ago

One way outdoor dog gate

5 Upvotes

Does anyone have any idea how I could install an outdoor one way dog gate. We have a fence around our garden but walk our dogs outside of the garden fence on our property. Some of the more energetic dogs roam around the property after the walk. It’s not a problem for us but I would like to install a flap/gate/fence that these last stragglers could use independently to enter the main garden. I have seen a wooden one at this link https://www.instagram.com/reel/Df2S85-uHut/?cnvx=MTdsNGdqbjU3aWQ3dQ== but I think it will be too heavy. Any ideas. Also before the criticism comes, we have 9 Thai street dogs that we rescued from abominable circumstances and my husband and I flew to France when we left Thailand. They are not neglected if they hang out in the field on our property


r/FenceBuilding • • 13h ago

Hot-dip galvanized 3D V-bend perimeter fence — coating, panel stiffness, climbing resistance (manufacturer, happy to answer spec questions)

1 Upvotes

The panels are hot-dip galvanized, so the zinc covers the wires, the welds and the post edges rather than sitting on top like a paint layer. The V-bend ribs give the panel stiffness, the mesh opening is tight enough to make climbing awkward and to keep livestock in, and the welded joints are the load path under impact. Panels and posts ship ready to assemble. If anyone is comparing coating types or mesh specs for a site, ask away.


r/FenceBuilding • • 14h ago

Barb wire? How old would you guess?

Thumbnail
gallery
17 Upvotes

r/FenceBuilding • • 19h ago

Snow Fence Help

Thumbnail gallery
2 Upvotes

r/FenceBuilding • • 20h ago Bravo

Cedar Fence

Post image
6 Upvotes

Looking for guidance on building a simple 6' cedar picket privacy fence. My sister recently bought a house with a small yard. One of the things that needs done is the wire fence torn down and a cedar privacy fence put up (300' roughly)

Ive only ever built rolled wire panel fences, meaning the only applicable knowledge I have is digging holes and setting posts. When I looked into cedar privacy fences, I was pretty quickly overwhelmed with the sheer amount of options and choices that make building one vastly different from building another.

My sister just wants a simple privacy fence. From what I have found, this entails posts set every 8' with low/mid/high rails between and attaching pickets to rail. I see 5x5 posts are also recommended, however the only local option here is Lowes or HD, which means 4x4 or 6x6 (which seems like overkill).

Ive drafted out a rough lumber supply list that constitutes (45) 4x4x8 for posts, (120) 2x4x8 for rail and (600) cedar 5/8x5-1/2x 6' dog-ear pickets. Obviously there will also be screws and concrete ordered and I've gotta figure out a plan for a gate, but is there anything obvious I'm not accounting for? Is there any tips to ensure the fence is built as well as possible for being a budget-friendly privacy fence?

*Also, yes I know I accounted for each corner post twice when counting on my sketch, this was deliberate so I'd remember to order atleast a few extra posts in case some are severely warped.

I appreciate the help, just don't want to screw up the job in the effort of helping out a family member!


r/FenceBuilding • • 21h ago

Lowe’s Catalyst Newbury?

Thumbnail
gallery
1 Upvotes

I moved into my house a few years ago and am now trying to fill in a 20ft gap in our fence. I want to get the matching 6x8 vinyl white privacy fence in the picture. I’m pretty sure it’s the Lowe’s Catalyst Newbury privacy, but am having a tough time confirming. I went to a Lowe’s today and nobody could help me and there were no samples. The Lowe’s website also isn’t super helpful. Is anyone able to confirm based on look and the tongue-in-groove style?

The pickets and rails match the Newbury specs.


r/FenceBuilding • • 22h ago

Is this a fair price?

3 Upvotes

I’m getting estimates for a 6ft tall privacy fence, 165 linear ft, pressure-treated pine, with two 4ft-wide gates. The most recent proposal came in at $8,100 including tear down and removal of my old wood privacy fence. Is this a fair price?


r/FenceBuilding • • 1d ago

Recycled birdhouse fence

Thumbnail
gallery
1 Upvotes

My elderly neighbor had a 6 foot wood fence blow down in a storm. It was an older thick beast but in my damp climate it deteriorated at the base over 50 years and most of the cedar boards were rotten along the bottom. I took it all apart, removed any nails and trimmed down all the rot off the fence boards to a consistent length and ripped some of them down the middle. Also trimmed off the posts and installed the new shorter posts so the height of the new fence is closer to 4.5 feet. I did have to purchase one new 4x4 PT post and two new 8 foot pt 2x4s to complete the base (also new cement and hardware) so this isn't 100% recycled but close.

I then installed the verticals in a revolving pattern with some air gaps in between. I had some extra cedar scrap at the end so I made some custom birdhouses that fit over the 4x4 posts. These are mostly decorative to protect the posts but I have seen birds actually using them.

My neighbor made me a plate of cookies so it was a good trade.


r/FenceBuilding • • 1d ago

Will these be fine for outdoor fence?

Thumbnail gallery
0 Upvotes

r/FenceBuilding • • 1d ago

Advise please

Post image
0 Upvotes

I'd like advise and opinions on what I should do here. We pushed our fence back 3ft. And these new sections need to be cut down the match the original fence. I started to cut a straight line that matched the panel to the left. Until my wife pointed out that the section on the right is much higher.

Should we angle these boards from right to left? Or cut them straight but each lower than the next to match the height difference? We did the caulk line as a visual of the angle but the look wouldn't match how the other panels compensated for the grade of the yard.

Never built a fence before and I want to finish it off as best as I can without looking out of place. Any help would be appreciated.


r/FenceBuilding • • 2d ago

How to set post in standing water?

2 Upvotes

I'm fencing my backyard and I have one hole that has ground water leaking into it from somewhere. It's just a tiny trickle, but it leaves a couple of inches of water in the hole and I definitely need a post in this exact spot. Is there a good way to install a post in a hole with a bit of water in the bottom? Can I throw some concrete mix in with it? I assume this one is going to rot way faster than the rest of the posts in the line.


r/FenceBuilding • • 2d ago

Manually driving Postmasters

5 Upvotes

I've finally sourced a handful of 10 foot Postmasters and I need to plant them in the next two weeks before the ground freezes. It's too cold for concrete now, and I really don't want to do concrete because. I don't think I can or want to source a gas powered driver and adapter because this is my first rodeo and things could go awry too quickly. I need to get them 4 feet underground. What are my best options for getting them in the ground and having them stay plumb?

(A) dig a four foot hole, set the posts in place, then add dirt a few inches at a time and use a digging bar to pound the dirt

(B) adapt a manual post driver somehow:

(i) angle grind notches in the post driver

(ii) build an adapter from stock metal parts

(C) some combination of the above or something else

Thanks


r/FenceBuilding • • 2d ago

Anyone near Littleton, CO have a PostMaster fence post driver I could borrow or rent?

3 Upvotes

I'm installing PostMaster steel fence posts and have had no luck finding a compatible post driver to rent anywhere near Littleton, CO.

Does anyone have a Titan PGD3200XPM, Rhino PostMaster driver, or another compatible driver they'd be willing to lend or rent out?

Thanks!


r/FenceBuilding • • 3d ago

Potential concerns on no dig pvc fence

Thumbnail
gallery
2 Upvotes

Seeing a lot of exposed pipe 3 years after installation of this no dig fence. Unclear if its soil exposure around the posts or if this is a bigger concern? Should the painted line be aligned to the ground?


r/FenceBuilding • • 4d ago

Couple of finished pics of this lodgepole fence we built. Starting to try and get more hardscaping adjacent jobs to my résumé. Ficus behind fence, mulch, and Santa Barbara daisy.

Thumbnail gallery
5 Upvotes

r/FenceBuilding • • 4d ago

Century Homes recycled fencing

Thumbnail gallery
36 Upvotes

Here are a few more examples of some recycled wood fences I made for some 100+ year old homes in Seattle. One of my first homes from 2004 and another from 2008ish. I don't own these any more but as far as I know the fences are still standing.

Not only do they have a large amount of recycled materials but they have frugal use of new materials as well. Most boards are cut in half or ripped in half to extend their use. I would be SHOCKED if any one of these fences had more than $500 in new materials.

The funny thing with using recycled materials is that you have to design around whatever materials you can scrounge at the time so results can vary wildly. Craigslist, dumpster diving, free piles, nice neighbors have all been sources.

Bonus- you can see how these have aged with different stains over time.

Bonus- gate made from recycled metal as I had access to a welding shop at the time.

Bonus- some recycled bird houses I made with the same cedar.

Bonus - dog tax. RIP Ruby, best dog ever.


r/FenceBuilding • • 4d ago

Repairing fence post less than 3.5years old and found bricks etc?? Normal or...

Post image
2 Upvotes

so, had a full fence done in March 2023, all seemed a great job, good to deal with etc etc but Ive noticed 4 out of 9 posts are leaning so investigated. Ones definitely snapped, 2 just a bit loose (I was putting this down to the very very dry summer, probably naively) and one I was sure was rotten.
So, before we get right into winter I've decided to investigate and repair 2 of the ones I can get at easily, (other 2 are behind a shed) and I've got two of 100mmx100mmx1200mm concrete spurs and started the process yesterday. One was the slightly loose one as in the picture which is obviously also rotted and the other has definitely rotted which is the one I was most worried about.
Now Im grand at setting about the repairs, but you can see in the photo there's a red brick in the concrete of the post that was just a bit loose and I'm sure this cannot be proper practice to add this into the concrete to support a fence post?
Anyone able to confirm my theory that they've not done a proper job after all?


r/FenceBuilding • • 4d ago

At what point will a gate adjustment be classified as an issue of poor workmanship?

3 Upvotes

I reviewed the warranty policy of my automated gate and found that they provide warranty for workmanship, and warranty on the installation and labour involved in calibrating or adjusting a new automatic gate. I then began to wonder about a potentially defective gate that starts dragging or not closing properly after five to six months of use. Does one know whether the defect was caused by poor installation or is simply an adjustment that needs to be made? What other possible causes of the defect must be considered, including the hinges, alignment, posts or settings? To be specific, I current consider a bay area lions gate offering, and given it is to have a clear understanding of the cost of the service call, how do most companies determine what constitutes bad workmanship versus a simple adjustment?


r/FenceBuilding • • 4d ago

Trenching for fence install

3 Upvotes

Hey all

We're looking to have a 4 board fence installed on our property in SC. One of the quotes we got the builder says they typically run a trench the full perimeter instead of digging for each post. The guy says it's a lot faster. Anyone heard of this before? Any opinions on the risks?


r/FenceBuilding • • 4d ago

Is there any point to only getting one side of fence stained, besides just looks?

7 Upvotes

If I don't stain both my and my neighbors side of fence, would it still offer the benefits of preserving the wood longer?


r/FenceBuilding • • 5d ago

How to use old fence panels to make new fence

1 Upvotes

Good afternoon beautiful people-

First off- I don’t know anything about wood working but this economy makes us all DIY enthusiasts. I bought some fence panels from Facebook marketplace that I hoped to repurpose into a fence for my own yard. I figured I would place the posts and nail in the old panels….

The problem is all of the left over nails. I have no idea what would be the best way to get rid of them. I bought a cats paw tool but the nails are so brittle that the nail head chips off.

I thought maybe I could cut off those parts with the nails but I’m at a loss on how to secure them to the posts….

Please give me any suggestions ✨✨✨


r/FenceBuilding • • 5d ago

New aluminum fence installed with dry-poured concrete. Should posts still move after 72 hours?

2 Upvotes

UPDATE: Spoke with the installer, and he said the concrete should have hardened, but when they return next week to install the final section containing the gate, we will do a walkthrough, and if, for some reason, the concrete has not set, we will discuss remedies. It is obviously too late to remove every post and wet mix and repour (I assume), so we will see what his fix is if they haven't set yet.

____________________________________________________________________________________________________________________

I recently had an aluminum fence installed and I'm a little concerned about the workmanship, specifically the dry-poured concrete and the movement I'm seeing at the base of the posts.

I've spent some time searching Reddit and other forums, but the answers seem to be all over the place. I'm not a fence installer, so I'm hoping some people with experience can help me understand what's normal and what isn't.

Fence information:

  1. Aluminum fence.
  2. 2" x 2" posts with approximately 6 ft wide panels.
  3. Fence is approximately 4.5 ft tall above ground. Posts are 7 ft long, so approximately 2.5 ft below ground.
  4. Soil is predominantly clay.
  5. Weather has been relatively cool, with highs around 70°F and lows in the 40s.
  6. It rained a couple of days before installation, but otherwise it has been fairly dry.
  7. Fence was installed approximately 72 hours ago.
  8. Posts were dry set using what looked like one bag of concrete per hole, followed by water from a garden hose at the end. I'm not sure how much water they used or how long they watered each hole.
  9. I'm not sure whether the concrete was QUIKRETE, Sakrete, or another brand, or what specific mix was used.
  10. I don't know the exact diameter of the holes but i think the super said 8 inch.

My main concern:

When I push a post, there's noticeable movement right at ground level. I'm not talking about the normal flex you'd expect from a relatively thin aluminum post toward the top. The movement appears to be happening down at the base.

My questions:

  1. Is dry setting concrete common practice specifically for aluminum fences? I've seen people say it's completely normal and others say it's a terrible way to install a fence.
  2. After 72 hours, should there still be any noticeable movement at the base of the posts? Or should they be pretty solid by now?
  3. How concerned should I be about the amount of water used? If they just sprayed the top of the dry concrete with a hose, is there a chance the concrete farther down never got enough water?
  4. Does approximately one bag of concrete per post sound reasonable for this type of fence, assuming a typical hole diameter?
  5. If this isn't normal, is there a way to check whether the concrete was properly set without digging everything up?
  6. Should I be documenting anything with the contractor now in case the posts loosen up or start leaning in the future?

I'm not looking to give the contractor a hard time or find excuses not to pay him. I just want to make sure the fence was installed properly and isn't going to become a problem a year or two down the road.

I can provide photos or videos of the movement if that helps. Appreciate any input from people who install these regularly.