r/FixMyPrint • u/Naive-Noise9167 • 2h ago
r/FixMyPrint • u/a_lachlan • Nov 05 '24
Helpful Advice Here’s your daily reminder to dry your filament
Thought it was stored dry so I’d try printing without drying first as it wasn’t going to use much filament anyway, didn’t get away with it this time but after 6 hours of drying it printed perfectly 👌 Sunlu dryer at temp setting 2 for Matte PLA with a load of colour changing silica gel in the middle of the role rather than in the compartment at the back of the dryer
r/FixMyPrint • u/heir-of-slytherin • 7h ago
Fix My Print Help with PLA+ ironing settings on P1S
Printing this Christmas wreath for my wife on my Bambu P1S with AMS. I thought I had the ironing settings down after doing a test print, but this is the final result. The ironing turned out super smooth on the red and lighter green parts, but the dark green top layer is very rough.
The filaments are slightly different. Dark green is Inland brand PLA+. Red is Insignia PLA+ and green is Insignia PLA.
The setting I used were:
Ironing type: Too surfaces
Ironing pattern: rectilinear
Ironing speed: 35 mm/s
Ironing flow: 20% (saw small gaps with 10% in my test)
From my research, it may have more to do with the top layer quality rather than the ironing, but I don’t know why the red and green ironed so well while the dark green didn’t with the same top layer settings.
r/FixMyPrint • u/GyoJinSho • 1h ago
Fix My Print Recently swapped to .2mm nozzle, and had no issues with my first 4 prints, now this happens no matter what I try to print.
I recently swapped all my hotends to be .02mm nozzles, and after printing fine with no issues for around 60 hours of usage, now this is happening. I’ve been careful to keep all my PLA in dry boxes at around 15% humidity on average, any ideas?
r/FixMyPrint • u/Federal_Engineer5654 • 1h ago
Fix My Print Failing On First Layer
Tried printing a benchy on a used ender 3 I bought. It comes out kinda stringy and messy. This is just after the first layer. I just adjusted the Z offsets because it was off but still had this same thing happen. Unsure what's going on and would love some advice.
r/FixMyPrint • u/baconeggchz • 8h ago
Discussion What causes this web like stuff on my prints?
Model is a P2S. I have an a1 mini and this doesn’t occur on this with same Elegoo filament PLA+. It’s not the end of the world and I can easily take it off but rather ask what it causes this.
r/FixMyPrint • u/Mintyboi10 • 3m ago
Fix My Print I’m trying to print this specific part, but whatever I do it fails. What now?
First attempt: auto orient. Failed about 3 times
Second attempt: oriented it myself and added supports. It got about 70 percent done before shitting the bed
It seems the prints would always get disconnected from the bed and then got flung everywhere with a big string of filament attached. I don’t know what to do since these pieces here I printed with a group and printed just fine along with the rest of the group besides the fact that it doesn’t fit the hole I need. Now that im trying to make them again it just won’t work
r/FixMyPrint • u/SillyArmadillo3176 • 3h ago
Troubleshooting 300mm ASA is acting up
For short, i designed a part i want to print, no issues in pla but ofc ASA is acting up and the corners/edges are either lifting or getting bubble like artifacts.
My setup is:
Creality CR10 Pro V2 with a housing made from plexiglass,
I let the whole thing preheat for about 30 minutes
My bed temps where all between 110-90 and print temps of 270-255
I use the Orcaslicer
I can print a benchy fine but larger flat things seems to be a big problem.
Ive heared you should have a heated chamber but i couldnt find a afordable printer with a bedsize of 300x300.
Any help is appreciated!!!
r/FixMyPrint • u/steve_simpson • 5h ago
Troubleshooting Wavy extrusion on MK4S
galleryI’ve been trying to troubleshoot this wavy extrusion on my Mk4s for weeks and I’m losing my mind. Has anyone here run into this issue? I’ve rebuilt the nextruder, swapped out the thermistor and heater, changed the loveboard, replaced the main cable, belts, idlers, etc. any advice is appreciated.
Printer is a prusa mk4s with firmware 8.0.0, prusaslicer 3 and 2.9.7, and elegoo PETG on 0.2mm structural. Printer temp is 235 for first layer and 250 after, with 85c bed.
r/FixMyPrint • u/AdLeading6357 • 5h ago
Fix My Print PETG, any idea what causes this?
galleryr/FixMyPrint • u/J3R4N • 3h ago
Fix My Print Troubleshooting some banding
Bambu H2D
Orca
Hatchbox PLA Silver (calibrated)
.2mm nozzle @ 220° | 55° bed
.1 layer height
60mm/s outer 100mm/s inner (5 walls)
Inner/Outer + Precise wall
Arachne
Auto PA
Retraction .8
8% Gyroid
I haven't yet tried another material but I did have this same issue on 2 machines. Machines are on different tables and ran different spools. Slicer shows pretty consistent layer times and line width looks even. This material is slightly shiny so I'm wondering if I'm having partial clogs or something.
Just wanted to do a sanity check before I go down the rabbit hole trying to sort this out.
r/FixMyPrint • u/RapozaDynamica • 3h ago
Fix My Print Uneven walls striped effect
Every print I make has these very consistent "inconsistent" walls, it's very faint and you can barely feel it, mostly shows up under specific light, but still something that bothers me.
This is an example of a vertical printed test (these dashes are just supports, the issue happens on all prints so it's not them) that was printed with inner/outter settings. When printed with inner/outter/inner it gets better but doesn't fix it entirely
It happens pretty universally with any model and filament, but for this one specifically, it's using Elegoo PETG-CF at 280c, on a Sovol SV08Max with DKEU, with a hardened steel 0.4mm nozzle.
I've calibrated my PID for both nozzle and bed, tried both 65 and 200 mm/s speed, 3000 and 7500 accel, dried up the filament for 12 hours at 70C, arachne and classic made no difference. Printed several 20mm cubes and all of them have the same issue, but they do not have the same pattern across them, so I believe it excludes an issue with the Z axis I imagine. I also tensioned the belts using an bike chain app on both X, Y and Z axis (left 15cm of space between the dead ends and tuned to Sovol's reccomended frequency). Extra settings I used on comments
Only setting that I've changed that made any meaninful difference was making it inner/outter/inner, but I think that's just hiding another issue rather than fix it.
Any clues?
r/FixMyPrint • u/SillyArmadillo3176 • 3h ago
Troubleshooting 300mm ASA is acting up
For short, i designed a part i want to print, no issues in pla but ofc ASA is acting up and the corners/edges are either lifting or getting bubble like artifacts.
My setup is:
Creality CR10 Pro V2 with a housing made from plexiglass,
I let the whole thing preheat for about 30 minutes
My bed temps where all between 110-90 and print temps of 270-255
I use the Orcaslicer
I can print a benchy fine but larger flat things seems to be a big problem.
Ive heared you should have a heated chamber but i couldnt find a afordable printer with a bedsize of 300x300.
Any help is appreciated!!!
r/FixMyPrint • u/SillyArmadillo3176 • 3h ago
Fix My Print 300mm ASA is acting up
For short, i designed a part i want to print, no issues in pla but ofc ASA is acting up and the corners/edges are either lifting or getting bubble like artifacts.
My setup is:
Creality CR10 Pro V2 with a housing made from plexiglass,
I let the whole thing preheat for about 30 minutes
My bed temps where all between 110-90 and print temps of 270-255
I use the Orcaslicer
My cooling fan is set to 0 for the entire print
I can print a benchy fine but larger flat things seems to be a big problem.
Ive heared you should have a heated chamber but i couldnt find a afordable printer with a bedsize of 300x300.
Any help is appreciated!!!
r/FixMyPrint • u/Arpegio22 • 17h ago
Fix My Print Posting again to ask what the problem is for top layer
For some reason the top layer would end up looking like this no matter what pattern I take when there is regularly spaced holes between them, but when there are none the top surface looks alright, this happened after I tried to fix the gap on first layer for concentric pattern that I had a problem by increasing the first layer width.
Printer: Ender 3 V3 SE
Slicer: creality print
Filament: PLA
Nozzle Temp and Bed : 205 and 50
r/FixMyPrint • u/ThomazFF • 4h ago
Fix My Print How to add holes to fill the printed part with sand?
r/FixMyPrint • u/Gold-Needleworker489 • 5h ago
Troubleshooting Elegoo Help
Hello! So im really new to 3D printing. I recently changed the nozzle on my Elegoo Neptune 4. I watched their youtube video on how to do it and at first it started making rattling noises with the cover on. So I took the cover off which fixed that problem. But now whenever I try and print anything it wont stick to the plate and gives me this error code. Can anybody help me please?
r/FixMyPrint • u/Outrageous_Grade5692 • 5h ago
3D model Just finished printing the Burj Khalifa! Turned out surprisingly clean on the spire.
r/FixMyPrint • u/ReiCaolho • 12h ago
Fix My Print Help with print with low quality details
galleryr/FixMyPrint • u/Sure_Farm4172 • 7h ago
Troubleshooting Need help with Anycubic Kobra 2 Neo
So sorry if this isn’t the right place for this but I honestly don’t know what to do anymore…. Would be grateful for any advice!
r/FixMyPrint • u/edot4130 • 13h ago
Fix My Print Help with Hyper Petg
Helping my son print a clone trooper helmet and we are having some trouble getting a good result. We did an initial temp, flow rate, and pressure advance calibration to come up with the settings below. Made a go of the first print and it wound up failing a while in (lost some supports) so figured we would take this as an opportunity to dial in the settings a bit more and hopefully produce a better result. Still kind of new to this and especially the hyper petg, any advice would be greatly appreciated. For some context the first two photos are of the outside rim of the helmet and the second two are of the face slit front/back. I am a bit stumped because it seems to be both under extruding (leaving voids) and then over extruding (leaving blobs) at the same time. Any suggestions on how to improve the result would be greatly appreciated!
Creality K2 Plus - .4 nozzle
Creality hyper Petg
Flow ratio .98
Nozzle Temp 235
Bed temp 70
Retraction speed 40
Print speeds- see last photo
Pressure advance .05
37% RH in CFS
r/FixMyPrint • u/-_-Helloooo-_- • 9h ago
Fix My Print how do I fix this?
What are these weird gaps between my layers and how do i fix it? This was printed with a Bambulab P2s and with dark grey pla standard (recently dried).
these are my settings:
- wall order: inner wallouter wall/inner wall
- smoothing wall speed along Z: enabeld
- 3 wall loops
- infille: gyroid
- outer wall speed: 30mm/s
- inner wall speed: 80mm/s
- nozzle temp: 200 degrees celcius
- bed temp: 60 degrees celcius
- dont slow down outer wall: enabeld
Thanks in advance!
r/FixMyPrint • u/NerdMachine • 14h ago
Fix My Print I can't seem to get a good first layer with Bambu PETG HF


Ender 3 v2
Bambu Labs PETG HF
Using the stock plate with glue stick
Nozzle: 0.4mm, line width 0.6mm
Bed temp: 70C
Nozzle temp: 250C
Fan: 0%
I tried playing with the nozzle height with limited success. I'm wondering if this PETG is an exception to the "no fan for petg" rule, but this print is a functional part so I wanted to leave it at 0% for strength.
I dehydrated the brand new spool at 55C for 12 hours before printing.