Sewing machine needles come in a variety of sizes and types and many of the problems I see online are caused by using the wrong needle type.
Generally when you buy a machine it comes with universal needles in the box. Universal is a misnomer. They are very useful on a wide variety of woven fabrics. Universal needles in a size 12 are what I use for anything that is a medium weight woven.
Jeans needles are for heavy fabrics like denim and canvas. Generally I go up to a 14 or 16 in a jeans needle.
Microtex needles are super sharp. They are excellent for woven fabrics that are delicate, snag easily, or are tightly woven. I use them on silks, satin, and cotton poplins. When all else fails on a fabric, try a microtex. Microtex come in larger sizes and can be used on heavy fabrics. Microtex needles need replaced more frequently than other needle types.
Ballpoint or Jersey needles are the same thing, usually they are labeled as ballpoint in the US and Jersey elsewhere. Ballpoint needles are appropriate for stable knit such as cotton jersey with no or minimal stretch fibers added.
Stretch needles are similar to ballpoint needles in the sense that they are for knit fabrics. Stretch needles are intended for fabrics with a higher stretch fiber percentage and in addition to that they work well on more stable knits. They are what I keep in stock for working with the widest variety of knit fabrics. I usually buy 11 or 12 in stretch needles.
Super stretch are for super stretchy problem child knits, I have not tried these as they are relatively new on the market but I will be picking up a pack before I make swimwear again.
In addition to the types above there are a great many other needles with specific uses. Within each type there is a range of sizes and the needle size should be chosen to match your fabric and thread.
Needles are consumables and will become gradually dull as you sew. The rule of thumb is that you need to replace after roughly 8 hours of run time. If you have been using a needle for a while and things start to go wrong or the machine sound changes, the first step on troubleshooting is a new needle. Old needles can damage your fabric and are more likely to break.
I also want to advise against buying off brand needles and included in that category are Singer branded needles. I personally only buy schmetz and organ brand needles and I buy exclusively off wawak.com (US and Canada only).
We've been quietly working on something we hope makes this community a lot more useful — and today we're excited to share it with you.
What's in the wiki?
We built it to answer the questions we see every week — so whether you're picking up a needle for the very first time or you've been at it a few months and hit a wall, there's something in here for you.
Here's what's covered:
🧵 Getting started — What to make first, hand vs. machine, and the YouTube channels worth bookmarking
🪡 Machine buying guide — Budget breakdowns, brand recommendations, and how to buy a great secondhand machine
✂️ Tools & notions glossary — Every tool explained in plain English, plus what you actually need to start vs. what's nice to have later
🔧 Techniques & troubleshooting — Pressing, seam finishes, backstitching, and a troubleshooting table for the most common machine gremlins
📐 Pattern reading & sizing — Why sewing sizes aren't clothing sizes, how to read pattern markings, and what "ease" means
🎨 Fabric guide — Wovens vs. knits, beginner-friendly fabric types, pre-washing, and where to buy
🔗 Community resources — Our curated list of YouTube channels, blogs, and related communities
❓ FAQ — Detailed answers to the questions we see most often
This wiki belongs to all of us — and we need your help
A wiki is only as good as the community behind it. We're a team of moderators, not an encyclopedia, and we know there are gaps, things we got slightly wrong, and questions we haven't thought to answer yet.
That's where you come in.
We want to hear from you if:
💡 There's a topic you wish had been covered when you were starting out
🐛 Something in the wiki is unclear, out of date, or just wrong
🔗 You know a great resource (video, blog, pattern, tool) that should be listed
❓ You've seen a question come up over and over in the sub that deserves a proper answer
✍️ You'd like to contribute a write-up on something you know well
How to send a suggestion
Drop your suggestion right here in the comments. Tell us:
Which section it relates to (or if it should be a new section entirely)
What you'd like added, changed, or corrected
Any links or sources that would help
You can also message the mod team directly if you'd prefer, especially for corrections or anything that needs a longer explanation.
We'll review every suggestion and update the wiki regularly. If your contribution makes it in, we'll do our best to acknowledge it — this is genuinely a community project and we want it to reflect the knowledge that lives here.
A note on what makes this community special
This subreddit exists because sewing has a steep early learning curve and a long tradition of people helping each other climb it. Every question answered, every "here's what worked for me," every photo of a wonky first pillowcase posted with pride — that's what makes r/SewingForBeginners worth showing up to.
The wiki is our attempt to bottle some of that up so it doesn't get lost in the scroll. But it'll never replace the real thing, which is all of you asking and answering in the comments every day.
Thank you for being part of this. Now go make something. 🧵
Learned quite a lot doing this, most importantly that quilting fabric sucks and that the fabric used in cheap canvas drop cloths will easily fray through half an inch of seam allowance, but I have a nice laundry bag until the fabric gives out. I used the Industrial Tote pattern from Roughcut patterns.
Here's a few example I found on interest. Obviously these kind of clothes take a lot of different fabrics. Should I buy fabric scraps second hand for this? And what kind of fabrics should I look out for? I've seen a few people use quilting fabrics, which are a very stiff fabric. Could I also use other kinds of fabrics for this? :) Maybe someone knows a way you could use Jersey without making it too stretchy? Because I'm seeing a lot of printed jersey, but am afraid it would make the overall fit wonky if some of the fabric stretches.
And would it be better to use a base layer for some of the patchwork or is it not required? I think I've read some people use interfacing, or dissolvable interface fabric. I want to maybe start practice with some bags, but not make the clothes too stiff once I start on that.
I already managed to buy a whole quilting set from someone with some amazing fabrics for cheap, so I'm definitely going to work with that. But I don't want to spend an arm and a leg on meters of different kind of fabric.
I've also seen some people buy fabric bundles from places like aliexpress but I'm kinda worried about the quality of it.
I’m doing my first lil sewing project for gifts for my bachelorette guests. I’m hand sewing cutout fabric letters. So far I’ve used FrayCheck which has helped me out, and my stitches have been good I think n I’ve done good at securing them with my finishing knots.
Now I’m wondering what I should do to secure everything in place to withstand the wash. Maybe I’m being overly ambitious but I don’t wanna give people a high maintenance gift. I was gonna for sure recommend the shirt is washed inside out on delicate and probably just air dried.
But any other recommendations to add?
Thanks!
Hii! I’m currently thinking about making a hoodie from my old pyjama set (1 top and 2 bottoms).
Currently I’ve made new sleeves from the first pair of pants. The actual body part already fits somewhat well, but I’ve been thinking about widening it with the original sleeves or perhaps with the other pair of pants. However I’m not really sure if it’s worth the hassle of four side seams and ribbing (i’m not even sure if I have to detach it completetly not).
Other than this I was also planning on attaching a zipper (the body’s panda side will be on the back!), making a hood of course and perhaps a kangaroo pocket (if I even have any more fabric at that point :D).
I think what I’m asking is just if you think the struggle of widening the body is not worth it for a beginner. Other than that you can just vibe with the pandas🐼🐼 :)!
Hi! I’ve been sewing for a few years but am just now learning how to fit and make adjustments.
I’ve been trying to figure out why all of my fitted clothes come out too tight in the chest even though I am using the correct bust measurement, or sometimes a size up, and I’ve realized it’s because I have a very wide ribcage and underbust. I do have a full bust, technically, but I think that’s because ribcage gets super wide there rather than because I have boobs in the front.
There are a lot of resources out there for full busts, but adding darts or fullness in the front I feel like doesn’t necessarily help me because all the width there is on the sides.
Are there any resources or fitting methods for this issue??
Is it easier to make two or three sizes up, then dramatically reduce the waist??
Obviously this is something that needs to be hand sewn. I’m wondering what specific hand sewing technique you would use in this case? It’s the arm seam so I want it to be strong! It’s a mink fur coat. I’ve never sewn fur before.
hey guys, i found this sewing machine at goodwill on sunday! i been wanting to learn how to sew for the longest time so when i saw it was only $30 i had to buy it. i’m excited i haven’t started using it yet bc it’s been a busy week for me but hopefully i can soon. what do you guys recommend i buy to get started?
Hi! I looked through the sub and read several 'which machine do I buy' posts but I feel like I know even less now lol. Basically, I am a complete beginner in machine sewing - I sewed one stitch on my partner's mother's machine and that's it. I want my own machine but I am completely lost as to which one do I choose (or rather: which one do I request for christmas).
I *think* I narrowed the brand to Janome (as I gathered here, new Singers are not good, Juki machines are not easily accessible here and for some reason I just don't want a Brother - I don't know why, some sort of intuition just tells me 'don't').
Here's where the problem starts: I have no idea which model I should be looking at. What types of stitches do I need if I'm planning on sewing some basic clothes (my partner has it in his head that one day I will be good enough to sew him a suit from scratch lmao - I don't believe this day will ever come but for the sake of narrowing 'clothes' down you can assume this will be the most complicated thing I will ever attempt). I don't foresee sewing denim or leather so heavy duty is not a must, but if there's something that is generally good and can handle heavy fabrics on top of that I will not complain.
Also, do I need automatic needle threading? Are there any additional functions I should look for? And what is rotary hook vs oscillating hook - and which one should I be looking at?
Please, help a sis out here!
Additional context: I was considering buying the same machine that my partner's mother has (since it would be nice to have someone to help me learn it) but that one is a vintage Polish one from a brand Łucznik (I think it's from the 80s, maybe even older) - since she got it, the brand got sold to a Chinese corporation and has apparently, according to Polish seamstresses from the Internet, turned totally useless, so that's a no-go. And since I'm requesting this for Christmas I want to go for a new one instead of refurbished vintage - it's easier to find and buy and I don't want to cause too much of a hassle for the person getting it for me.
I searched and didn't see much on machine recommendations. I'm hoping to spend a max of $300, would rather it be closer to $200. I need to be able to hem jeans I think I need zigzag stiches so I can do stretchy fabrics. I want it to have a free arm.
I'm pretty technical and mechanical so I don't mind learning a complicated machine. What matters most to me is how the machine feels to use if that makes sense. I know people say the machine doesn't really matter but I will get discouraged if it's more difficult to sew than it could be because of the machine.
I was kinda set on a singer heavy duty one but I was several comments to stay away from them.
first time trying a pattern like this (have previously made smaller things like wallets and bags, and altered clothing, but not made clothes from scratch before) and trying to work out the layout for the interfacing, but run into some confusion about numbers and pieces? looking at the layout, it's wanting two different number one pieces, the actual number 1 and another with a similar shape to 15, but with a pointed end instead of the flatter one on 15?
my only guess would be potentially disregard as theres mention of a piece 1a in the larger sized patterns? but that also states to attach those and cut as one, and is only for sizings 46-52, and i have 38-44 (making 44 as its for my partner, he measures 42 but being a coat, might want jumper room underneath, and can always take it in a lil, but harder to add fabric than take it off?)
any help would be greatly appreciated as I really wanna get this right, and have run into confusion before ive even began 😅 I know its probably a bit of a big project for a first, but he wants it for Christmas so not much time to practice elsewhere 😭
I am in Canada Ottawa, I been looking for a decent machine for a while. And happened to see Brother is on sale and it just fits into my budget that about $200. Any opinion on Brother machines?
I also checked FB marketplace. machines for sale around me either cost about the same or too old, or sold as is (the $120 Brother)🥲.
what it says on the title! i’m looking to sew a baby blanket for my friend and don’t know what kind of fabric to get. we live in a place where it can get extremely cold in the winter and fairly hot in the summer, so i’m unsure whether to go for breathability or insulation (or if i should splurge on wool for both*, or if that’s even worth it for a piece that will have to be washed frequently if it is used). all i do know is that i should avoid heavily dyed fabrics for allergy reasons. any advice appreciated 🙏
*assuming that’s what wool does. i could have learned wrong!
So, I got myself a refurbished Bernina records 730. Fully functional and came with all the old threads and feet that are older than me.
It took me a while to get a hang of it but... I broke 5 needles within a week. Granted I am a complete newbie and the only sewing machine i had was a toy grade from amazon. Also the needles are probably older than me.
My friend who took formal class told me the needles should bend, not break.
Basically I know that I am using the wrong sizes, and not know what i am doing but I was surprised at how brittle they are. I ordered 400 more needles (300 cheap ali express, 100 high quality from Bernina). Or do you think maybe the needle holder is bent and etc.? I mean there are times when it does get frustrating to thread because I am getting the tensions wrong but when it works, it's a dream machine.
Edit:
I got curious and used the needle from my cheap toy grade sewing machine on the Bernina, zero needle break. I mean I must say that the needles that came with the machine are from the 80's or older. Granted I was not gentle/using them correctly but I think the needles were at a fault too.
The photo above is the army of dinos I made for my friends.
I took a sewing class in high school and it was a lot of fun! My favorite thing to make was plushies, but I only made dinosaur plushies. Now I want to branch out and try some other animals.
The only thing is I never know what to do for the face, specifically the eyes. Last time I used furniture protective pads, but it looks kinda soulless.
If yall have any tips I would highly appreciate it! I don’t have a sewing machine so I would be hand sewing it.
Hello! I’ve used a sewing machine before, but not very much, so I’d consider myself a beginner. I want to start making jeans, jackets, and clothes for myself. I know people say you shouldn’t start with projects like that, but I’m very patient and don’t mind trial and error. Do you think starting with more challenging projects will help me progress in the long run, or is it a bad move?
I’m very very green, so it could be user error but the bobbin thread / bottom side of the stitch (terminology?) has loops in it.
My understanding is that this means the top thread doesn’t have enough tension.
I have the manual and I can’t seem to figure out how to adjust the tension. Anyone know? I’m thinking it’s the knob right under the easy threading path but in the manual it actually doesn’t say what that one does, almost like they missed it in the diagram.