I am in the process of putting together the BOM for what I want to build and would like to run it by folks here for any feedback.
# Custom Modular 18-ft WLED Rope Lights — Bill of Materials (BOM)
**Project Overview:**
* **Scale:** 5 Columns, 2 modular 18-ft ropes per column (10 ropes / 180 ft total)
* **Design:** 12V WS2811 seed pixels pulled through 1/2" ID clear vinyl tubing with 3-pin xConnect screw ends so ropes can be run either **in parallel** (2 per column, e.g., double-helix) or **chained end-to-end** (36-ft single run with plug-and-play power injection).
* **Control:** 1 dual-output WLED controller per column (synced via WLED UDP Sync / DDP).
---
### 1. LEDs & Tubing (10 × 18-ft Ropes)
* **12V WS2811 Seed Pixels (Clear Wire, 3-Pin)**
* *If building 2.5 cm (~1") pitch (~220 px/rope, 2,200 px total):* **2× 1,000-ct rolls + 2× 200-ct strands** *(200 spare)*
* *If building 5 cm (~2") pitch (~110 px/rope, 1,100 px total):* **1× 1,000-ct roll + 1× 200-ct strand** *(100 spare)*
* **Clear Flexible Vinyl Tubing:** **200 ft** of **1/2" ID × 5/8" OD** (or 1/2" ID × 3/4" OD) UV-resistant PVC *(10 × 18-ft cuts + 20 ft spare)*
---
### 2. Controllers, Power & Enclosures (5 Column Boxes)
* **WLED Controllers:** **5×** Gledopto GL-C-016WL-D *(ESP32, 12V–24V, dual data outputs)*
* **12V IP67 Waterproof Power Supplies:** **5×** **12V 8.5A (100W)** for 2.5 cm pitch *(or **12V 5A (60W)** if using 5 cm pitch)*
* **Weatherproof Junction Boxes:** **5×** IP65/IP66 hinged ABS enclosures *(~6"×4"×3" or 8"×6"×4")*
* **Waterproof Cable Glands (PG9 / PG11):** **15–20×** *(3–4 per box for AC in + xConnect leads out)*
* **Inline Blade Fuse Holders + 5A Fuses:** **15×** *(16–18 AWG waterproof holders; 2 rope outputs + 1 injection lead per box)*
* **Wago 221 Lever Nuts:** **1 assortment pack (~25 pcs)** of 3-port (`221-413`) & 5-port (`221-415`) for `+12V` and `GND` distribution
* **Outdoor AC Power Cords (SJTW):** **5×** *(1 per column box)*
---
### 3. Waterproof Connectors & Power Injection
* **Female 3-Pin xConnect Pigtails (18 AWG):** **25×** *(2 per controller box + 1 per rope output end + 5 spares)*
* **Male 3-Pin xConnect Pigtails (18 AWG):** **20×** *(1 per rope input end + 1 per injection lead + 5 spares)*
* **xConnect Waterproof Screw End Caps:** **15×** *(to seal the unused top Male connector on each column + 5 spares)*
* **3-3-3 xConnect Power Injection T-Splitters:** **5×** *(1 per column; used between Rope 1 & Rope 2 when chained end-to-end at 2.5 cm pitch)*
* **18/2 Low-Voltage Outdoor Wire:** **100 ft spool** *(for 5 × ~19-ft `+12V`/`GND`-only power injection jumpers up to the T-splitters)*
---
### 4. Sealing, Soldering & Pulling Consumables
* **3/4" (19mm) Adhesive-Lined Marine Heat Shrink (3:1):** **1 roll / pack** *(~3–4 ft total needed to seal pigtail-to-vinyl tube ends)*
* **22–18 AWG Waterproof Solder Seal Wire Connectors:** **100-pack** *(~60–75 splices needed)*
* **100% Neutral-Cure Clear Silicone Sealant:** **1 tube** *(must be oxime/neutral-cure—avoid acidic acetoxy silicone so copper doesn't corrode)*
* **Pull String & Silicone Spray:** **1 each** *(mason's twine/fish tape + dry silicone lube for pulling pixels through the 18-ft tubes)*
* **UV-Resistant Zip Ties / Clear Mounting Clips:** **100-pack**
---
### Quick Wiring & Build Notes
- **Verify Pinout First:** Always check `+12V`, `DATA`, and `GND` with a multimeter in continuity mode before powering on—wire markings on seed pixel rolls vary by batch.
- **Power Injection Safety:** On the injection leg going into the 3-3-3 T-splitter, connect **only `+12V` and `GND`** (leave the center `DATA` pin disconnected), and always feed it from the **same** 12V power supply running that column's controller.
- **Test Before Sealing:** Power up and test every rope on the bench with WLED before applying neutral-cure silicone and shrinking the 3/4" marine heat shrink over the tubing ends.