r/WLED • • 1h ago

Public WLED visualizer

4 Upvotes

For some reason, I was really infatuated with with Empire State building website showing color preview and why the colors were what they were, so I vibe coded a site that shows WLED visualizer for my house. It runs on cloudflare workers and a home assistant app. Setup took 10 minutes and response time is pretty insane IMO 20fps. Definitely small use case here, but I was amazed with how fast Claude put this together and how well it works.

https://github.com/CarolinaControl/WLED-House-Live-Preview


r/WLED • • 7h ago

Power injection and power supply advice

4 Upvotes

Hi all,

I've been setting up 5V SK6812 LED strips with 60LED/m density, but I'm having some power issues. My setup is in the screenshot below - red shapes are the strips, yellow shapes are power supplies with ESP32 controllers and orange shapes are WLED segments (with start and stop LEDs) - I've named the segments by the controller they're connected with (Fink, Wendy, etc). I've optimistically set this up without power injections and found out this doesn't work well. The issues I have:

  1. The tail end of Fink Balk 2 is flickering
  2. All of Wendy is flickering on many effects and changing settings happens slowly and in very discrete steps
  3. Setting the brightness of Wendy above 20% or so causes the power supply to audibly whir. As I increase the brightness, it gets louder. I've swapped out my power supply for another one and it has the same issue.

My questions:

  1. How much power injection should I be doing (and where) along the Fink and Wendy to fix the voltage drop issues? Online recommendations seem to indicate every 0.5-1m or so, but the Mark, Bobby and Lisa strips are in the 1.5 - 2m range and don't have issues. I don't need to be running these at full brightness, I just want to solve the flickering.
  2. AI is telling me the whirring is caused by the power supply being close to its limit. Does anyone know if this is true? The power supply is 5V/20A and the max current needed according to WLED is 55mA * 308 = 17A, but I'd be surprised if it reaches that due to the voltage drop issues and limiting in WLED. Also, the whirring starts at low brightness too. Would upgrading the supply to e.g. 30A or 40A make a difference, or is there a different issue?

Thanks in advance for your help!


r/WLED • • 19h ago

Need some help

2 Upvotes

So I have a small stage lighting project I’m working on. It’s more about ambience and prop lighting than full stage lights.

Currently I have an esp32 with some addressable 5v LED strip and just using wled off the phone. Everything is working well so far as a basic prototype.

I want to now figure out how to step things up to a more robust system which is capable off having multiple lights daisy chained around a stage. Just as a rough estimate I’d like to have 3-5 different LED strip lights around the stage and to have them daisy chained so the chase effect can go between the different lights.

So I’m trying to figure out a good way to get data signal between them, either by sending it between all the lights in a daisy chain (this could end up being 15-20m) or is there a controller or an output device I can use that would allow me to have the lights wired back to a central point yet still give me a chase effect. I don’t really want the lights to only do the same effect at the same time.

So if you have some tips or help for me that would be great as I’m a bit lost as to which parts I’ll need and how to simplify it so I can just hang my lights and then connect the wires between them or back to a central point.

Also if there is a good all in one control box for this. Thanks heaps


r/WLED • • 2h ago

Not another square LED matrix! 👀

1 Upvotes

r/WLED • • 12h ago

QuinLED-Dig-Quad (v4) wire connectors: how to connect 14AWG wire? The connectors are so tiny

1 Upvotes

I have all kinds of ferrules, but the smallest that can fit 14AWG wire is too big to fit into the connectors [EDIT: the connectors to the LED strips].

If I try to just solder the end of the wire to stop fraying, sometimes I can get it to fit but it's not easy. Do I need to step down to a smaller guage just for the connector? I must be missing something simple....


r/WLED • • 19h ago

Help with pinouts for hub75

Post image
1 Upvotes

i have a" ESP32 38 Pin WROOM-32 V5 Development Board Dual Core USB C WiFi BT NodeMCU Dev "

I also have a hub 75 breakout board with these pinouts.

Do you guys have any idea which version of hub75 activated wled I can use for this?


r/WLED • • 21h ago

Ceiling light

Post image
1 Upvotes

Hello everyone.

I am trying to make some WLED Light under my ceilling in my living room. In the image there is a scheme how I am planning to do this. I don't have much experience with WLED project that why I want ask you, more experienced people if that will works or something need to be change or maybe you have different ideas. As you can see there will be Three strips of LED: 4,2m, 4,0m and 7,6m, ecause of lenght of the ceiling/wall. power supply and LED Controller will be in the first corner betwen 4,2 m and 4 m wall 1,5 m under ceiling. So the power cable lenght will be

5,7m, 1,5m, 1,5m, 5,5m, 5,5m, 9,1m.

and First data cable 5,7mm other two only few cm. Led be 12V and thats why i want put Power on two sides of the strip to be sure that there is no power drops.

I want use WS2815 12v LED , GLEDOPTO controller, Not sure what power supply.

As I said I am new in this did some research but as allways there is some concerns and want to do this right because dont have a chance to change anything when everythign be connected.

Hope i describe everything clear and most of You will understand.

Thank you very much for your help.