r/FixMyPrint • • Mar 29 '20

Asking for help... and how to actually get it

Post image
771 Upvotes

r/FixMyPrint • • Nov 05 '24

Helpful Advice Here’s your daily reminder to dry your filament

Post image
289 Upvotes

Thought it was stored dry so I’d try printing without drying first as it wasn’t going to use much filament anyway, didn’t get away with it this time but after 6 hours of drying it printed perfectly 👌 Sunlu dryer at temp setting 2 for Matte PLA with a load of colour changing silica gel in the middle of the role rather than in the compartment at the back of the dryer


r/FixMyPrint • • 4h ago

Fix My Print Help with PLA+ ironing settings on P1S

Post image
10 Upvotes

Printing this Christmas wreath for my wife on my Bambu P1S with AMS. I thought I had the ironing settings down after doing a test print, but this is the final result. The ironing turned out super smooth on the red and lighter green parts, but the dark green top layer is very rough.

The filaments are slightly different. Dark green is Inland brand PLA+. Red is Insignia PLA+ and green is Insignia PLA.

The setting I used were:

Ironing type: Too surfaces
Ironing pattern: rectilinear
Ironing speed: 35 mm/s
Ironing flow: 20% (saw small gaps with 10% in my test)

From my research, it may have more to do with the top layer quality rather than the ironing, but I don’t know why the red and green ironed so well while the dark green didn’t with the same top layer settings.


r/FixMyPrint • • 5h ago

Discussion What causes this web like stuff on my prints?

Post image
4 Upvotes

Model is a P2S. I have an a1 mini and this doesn’t occur on this with same Elegoo filament PLA+. It’s not the end of the world and I can easily take it off but rather ask what it causes this.


r/FixMyPrint • • 1h ago

Troubleshooting 300mm ASA is acting up

Thumbnail
gallery
• Upvotes

For short, i designed a part i want to print, no issues in pla but ofc ASA is acting up and the corners/edges are either lifting or getting bubble like artifacts.

My setup is:
Creality CR10 Pro V2 with a housing made from plexiglass,
I let the whole thing preheat for about 30 minutes
My bed temps where all between 110-90 and print temps of 270-255
I use the Orcaslicer

I can print a benchy fine but larger flat things seems to be a big problem.
Ive heared you should have a heated chamber but i couldnt find a afordable printer with a bedsize of 300x300.
Any help is appreciated!!!


r/FixMyPrint • • 2h ago

Troubleshooting Wavy extrusion on MK4S

Thumbnail gallery
2 Upvotes

I’ve been trying to troubleshoot this wavy extrusion on my Mk4s for weeks and I’m losing my mind. Has anyone here run into this issue? I’ve rebuilt the nextruder, swapped out the thermistor and heater, changed the loveboard, replaced the main cable, belts, idlers, etc. any advice is appreciated.

Printer is a prusa mk4s with firmware 8.0.0, prusaslicer 3 and 2.9.7, and elegoo PETG on 0.2mm structural. Printer temp is 235 for first layer and 250 after, with 85c bed.


r/FixMyPrint • • 3h ago

Fix My Print PETG, any idea what causes this?

Thumbnail gallery
2 Upvotes

r/FixMyPrint • • 47m ago

Fix My Print Troubleshooting some banding

Post image
• Upvotes

Bambu H2D

Orca

Hatchbox PLA Silver (calibrated)

.2mm nozzle @ 220° | 55° bed

.1 layer height

60mm/s outer 100mm/s inner (5 walls)

Inner/Outer + Precise wall

Arachne

Auto PA

Retraction .8

8% Gyroid

I haven't yet tried another material but I did have this same issue on 2 machines. Machines are on different tables and ran different spools. Slicer shows pretty consistent layer times and line width looks even. This material is slightly shiny so I'm wondering if I'm having partial clogs or something.

Just wanted to do a sanity check before I go down the rabbit hole trying to sort this out.


r/FixMyPrint • • 50m ago

Fix My Print Uneven walls striped effect

Post image
• Upvotes

Every print I make has these very consistent "inconsistent" walls, it's very faint and you can barely feel it, mostly shows up under specific light, but still something that bothers me.

This is an example of a vertical printed test (these dashes are just supports, the issue happens on all prints so it's not them) that was printed with inner/outter settings. When printed with inner/outter/inner it gets better but doesn't fix it entirely

It happens pretty universally with any model and filament, but for this one specifically, it's using Elegoo PETG-CF at 280c, on a Sovol SV08Max with DKEU, with a hardened steel 0.4mm nozzle.

I've calibrated my PID for both nozzle and bed, tried both 65 and 200 mm/s speed, 3000 and 7500 accel, dried up the filament for 12 hours at 70C, arachne and classic made no difference. Printed several 20mm cubes and all of them have the same issue, but they do not have the same pattern across them, so I believe it excludes an issue with the Z axis I imagine. I also tensioned the belts using an bike chain app on both X, Y and Z axis (left 15cm of space between the dead ends and tuned to Sovol's reccomended frequency). Extra settings I used on comments

Only setting that I've changed that made any meaninful difference was making it inner/outter/inner, but I think that's just hiding another issue rather than fix it.

Any clues?


r/FixMyPrint • • 1h ago

Troubleshooting 300mm ASA is acting up

Thumbnail
gallery
• Upvotes

For short, i designed a part i want to print, no issues in pla but ofc ASA is acting up and the corners/edges are either lifting or getting bubble like artifacts.

My setup is:
Creality CR10 Pro V2 with a housing made from plexiglass,
I let the whole thing preheat for about 30 minutes
My bed temps where all between 110-90 and print temps of 270-255
I use the Orcaslicer

I can print a benchy fine but larger flat things seems to be a big problem.
Ive heared you should have a heated chamber but i couldnt find a afordable printer with a bedsize of 300x300.
Any help is appreciated!!!


r/FixMyPrint • • 1h ago

Fix My Print 300mm ASA is acting up

Thumbnail
gallery
• Upvotes

For short, i designed a part i want to print, no issues in pla but ofc ASA is acting up and the corners/edges are either lifting or getting bubble like artifacts.

My setup is:
Creality CR10 Pro V2 with a housing made from plexiglass,
I let the whole thing preheat for about 30 minutes
My bed temps where all between 110-90 and print temps of 270-255
I use the Orcaslicer
My cooling fan is set to 0 for the entire print

I can print a benchy fine but larger flat things seems to be a big problem.
Ive heared you should have a heated chamber but i couldnt find a afordable printer with a bedsize of 300x300.
Any help is appreciated!!!


r/FixMyPrint • • 14h ago

Fix My Print Posting again to ask what the problem is for top layer

Thumbnail
gallery
12 Upvotes

For some reason the top layer would end up looking like this no matter what pattern I take when there is regularly spaced holes between them, but when there are none the top surface looks alright, this happened after I tried to fix the gap on first layer for concentric pattern that I had a problem by increasing the first layer width.

Printer: Ender 3 V3 SE
Slicer: creality print
Filament: PLA
Nozzle Temp and Bed : 205 and 50


r/FixMyPrint • • 2h ago

Fix My Print How to add holes to fill the printed part with sand?

Thumbnail
1 Upvotes

r/FixMyPrint • • 2h ago

Troubleshooting Elegoo Help

1 Upvotes

Hello! So im really new to 3D printing. I recently changed the nozzle on my Elegoo Neptune 4. I watched their youtube video on how to do it and at first it started making rattling noises with the cover on. So I took the cover off which fixed that problem. But now whenever I try and print anything it wont stick to the plate and gives me this error code. Can anybody help me please?


r/FixMyPrint • • 3h ago

3D model Just finished printing the Burj Khalifa! Turned out surprisingly clean on the spire.

Post image
0 Upvotes

r/FixMyPrint • • 9h ago

Fix My Print Help with print with low quality details

Thumbnail gallery
3 Upvotes

r/FixMyPrint • • 5h ago

Troubleshooting Need help with Anycubic Kobra 2 Neo

Thumbnail
1 Upvotes

So sorry if this isn’t the right place for this but I honestly don’t know what to do anymore…. Would be grateful for any advice!


r/FixMyPrint • • 10h ago

Fix My Print Help with Hyper Petg

Thumbnail
gallery
2 Upvotes

Helping my son print a clone trooper helmet and we are having some trouble getting a good result. We did an initial temp, flow rate, and pressure advance calibration to come up with the settings below. Made a go of the first print and it wound up failing a while in (lost some supports) so figured we would take this as an opportunity to dial in the settings a bit more and hopefully produce a better result. Still kind of new to this and especially the hyper petg, any advice would be greatly appreciated. For some context the first two photos are of the outside rim of the helmet and the second two are of the face slit front/back. I am a bit stumped because it seems to be both under extruding (leaving voids) and then over extruding (leaving blobs) at the same time. Any suggestions on how to improve the result would be greatly appreciated!

Creality K2 Plus - .4 nozzle
Creality hyper Petg
Flow ratio .98
Nozzle Temp 235
Bed temp 70
Retraction speed 40
Print speeds- see last photo
Pressure advance .05
37% RH in CFS


r/FixMyPrint • • 7h ago

Fix My Print how do I fix this?

Thumbnail
gallery
1 Upvotes

What are these weird gaps between my layers and how do i fix it? This was printed with a Bambulab P2s and with dark grey pla standard (recently dried).

these are my settings:

  • wall order: inner wallouter wall/inner wall
  • smoothing wall speed along Z: enabeld
  • 3 wall loops
  • infille: gyroid
  • outer wall speed: 30mm/s
  • inner wall speed: 80mm/s
  • nozzle temp: 200 degrees celcius
  • bed temp: 60 degrees celcius
  • dont slow down outer wall: enabeld

Thanks in advance!


r/FixMyPrint • • 11h ago

Fix My Print I can't seem to get a good first layer with Bambu PETG HF

2 Upvotes

Ender 3 v2

Bambu Labs PETG HF
Using the stock plate with glue stick
Nozzle: 0.4mm, line width 0.6mm
Bed temp: 70C
Nozzle temp: 250C
Fan: 0%

I tried playing with the nozzle height with limited success. I'm wondering if this PETG is an exception to the "no fan for petg" rule, but this print is a functional part so I wanted to leave it at 0% for strength.

I dehydrated the brand new spool at 55C for 12 hours before printing.


r/FixMyPrint • • 8h ago

Fix My Print Help redesigning these

Thumbnail gallery
0 Upvotes

r/FixMyPrint • • 8h ago

Discussion Using an enclosure to help print PETG in a cold room? (Bambu A1 Mini)

Post image
0 Upvotes

r/FixMyPrint • • 13h ago

Fix My Print QUALITY PROBLEM

Thumbnail gallery
2 Upvotes

r/FixMyPrint • • 10h ago

Fix My Print Help my infill ruin my wall.

Post image
1 Upvotes

Problem i have is that I can see infill through my wall I'm using cura. Any setting to help this issue.


r/FixMyPrint • • 19h ago

Troubleshooting Diagonal line artifacts

Thumbnail
gallery
3 Upvotes

I tried printing this at a 0.08 mm layer height on my Elegoo Centauri Carbon with a 0.4 mm nozzle; everything was default for the 0.12 mm preset, and I only changed the supports to tree/strong and manually set the layer height to 0.08 mm. I tried changing the print order to inner/outer/inner and slowed the outer wall print speed to 60 mm/s from the previous 160 mm/s. The results were better but not as they should be, and I had other issues crop up.

Any pointers or suggestions would be appreciated.