r/gunsmithing • • 8h ago

Front Sight Soldering

Thumbnail
gallery
9 Upvotes

Browning hi Power had the front sight pop off while I was at the range, Ive spoken to several gunsmiths around me about soldering one of these new sights on and everyone keeps giving me deer in the headlight looks. Has anyone ever done one of these before ? Does anyone know someone I can mail this too to have the work done? Thank you very much


r/gunsmithing • • 1h ago

Remington model 760 game master- action opens itself after a shot

1 Upvotes

Just inherited my grandfathers old game master this year. While getting it sighted in I noticed the action was actually ejecting the shell itself after every shot without me retracting the pump. Is this a serious problem that Is worth getting taken care of before hunting season? I had the rifle resting on sandbags while shooting is it possible that is the cause?


r/gunsmithing • • 18h ago

Should I free float an old Weatherby with factory fore end pressure pad?

Post image
12 Upvotes

I'm having a heck of a time getting any consistency with this old 1991 manufactured, Howa built MkV 30-06. Tried a variety of factory ammo from 165gn to 200gn, tried some hand loads that shoot well in another rifle, checked the torque on the rings, am using a known good scope, and most recently, bedded the action. I'm still getting flyers, and i do mean flyers. It will put down a solid group and then a shot 4" off at 100. This is across all ammo tried. I never do long strings of fire. And the cold bore shot is usually poor, which doesn't lend itself to being a hunting rifle. Shots 2 and 3 are usually the best. Any more than that without cooling the barrel and it goes to pot. And before anybody asks it's not me flinching. I take several rifles to the range with me to shoot while the next one cools and my 280 Remington which weighs 4 lb less than this one kicks harder and I'm still putting down groups that touch. All of this is being done in a very solid bench rest setup.

So.... should I try adding some shims and see if it needs more pressure? Or is it time to bust out the Dremel? I'm not trying to make this 35-year-old rifle into a sub MOA tack driver. I know that will probably never happen. But it would be nice to get consistent inch and a half or even 2 in groups. I don't know if free floating it is just going to destroy it because the barrel is so thin but at this point I'm definitely willing to try different ideas.


r/gunsmithing • • 13h ago

Star Wars, Likelihood a smith can do this?

Thumbnail
gallery
5 Upvotes

So I would like to print a dc15 or dc15s and drop in a 22 assembly.
What is the likely hood a smith would have a setup to drill accurately into the “barrel” of the 3d print, and cut a slot for the receiver and trigger assembly?
I know you guys probably have lathes and mills but not sure on how this could go.


r/gunsmithing • • 10h ago

What era/exact model 93R17 trigger is this?

Thumbnail
gallery
2 Upvotes

It’s a stainless varmint 93R17. The trigger isn’t right or definitely someone did some home gunsmithing for match shooting (which i doubt not many 17s allowed in rimfire shoots) or they tried to make it lighter and went too far. I can close the bolt hard enough and the gun will fire. I can barely press the back of the bolt and the gun will fire. I cannot take the bolt out without removing the trigger, it’s like the sear it stuck up, curious the exact trigger cause there is so many and I cannot find this exact. Says the Gun is E receiver then it doesn’t look the exact as a e receiver trigger. Any help would greatly be appreciated. I took it all apart and took pictures, didn’t see anything out of the ordinary broken. (Yes I’ve already tried turning the set screw on the front all the way in and out. Same result)


r/gunsmithing • • 16h ago

RMR footprint mount on a SxS?

3 Upvotes

I am looking for someone that can cut out a portion of my cz bobwhite rib and weld/solder in a low profile RMR footprint plate. Does anyone have suggestions on who to reach out to that might take this on and do quality work? I


r/gunsmithing • • 20h ago

Stolen gun damaged

Thumbnail gallery
4 Upvotes

r/gunsmithing • • 20h ago

Stuck Mag Release on TortTort Receiver and Arsenal Kit

Thumbnail gallery
3 Upvotes

r/gunsmithing • • 1d ago

Restoration Help

Thumbnail
gallery
27 Upvotes

I have a 1914 Ranger Model 235 (I think thats the right model) it was found in a crawlspace with a whiskey still but it has this bit of wood missing. I dont have the wood and dont know how I could best go about fixing it. I have wood epoxy but idk that thats the best solution.


r/gunsmithing • • 23h ago

Cobray M-11/9 twitch FRT

1 Upvotes

I recently picked up a closed bolt Cobray M-11/9 and I wanted to pick up an frt for it. I was heavily considering the twitch frt, but was unsure if it would reliably work in this platform, as it is meant for the MPA defender. I saw one specifically made for the original cobrays from Advanced Reset Tech, but it is very expensive and I don't feel like dropping $264 dolans on a toy.

Basically, my question is this; Does anyone know if the twitch frt will work in an original Cobray M-11/9 or will it need fitment? I am fine with fitting it, just need to know what it would need.


r/gunsmithing • • 1d ago

Uberti 1873 lever gun failing to feed .38 even over 1.5 oal. Potential modifications I can make to get most .38 to feed?

Post image
3 Upvotes

r/gunsmithing • • 1d ago

1000 rds of 300blk supressed 10.5 in barrel dirty asf but wasn't jammin

Thumbnail
gallery
8 Upvotes

Got this thing chugging so good keeping em on target using frt out to 100 yards so far


r/gunsmithing • • 1d ago

DPM guide rod sticking out? HD 3.6

Thumbnail gallery
2 Upvotes

r/gunsmithing • • 1d ago

Do you see any damaged parts on these pictures of this Norinco 1897?

Thumbnail
gallery
1 Upvotes

Hello I am in contact with a guy who is selling his Norinco 1897 trench gun and he sent me some closeup pictures of the action and the inside of the barrel, since I'm not an expert on pump action shotguns, do you see any damaged parts of the gun in these pictures? Can I trust the vendor?

Thanks in advance!


r/gunsmithing • • 2d ago

Gunsmithing as a career

7 Upvotes

Recent high school grad been trying to figure out what I wanna do for a career and I have landed on possibly gunsmithing. Been around guns pretty much my whole life and have some knowledge in it and was just wondering how a career looks like in gunsmithing. Things like what schools would be worth looking into, what I will need to be successful, what the pay range is like, and if it is a path I should peruse would be helpful. Also hearing experiences from people retired or currently working as a gunsmith would be nice too. I’m in Texas specifically the DFW area so if there is schools around here that would be preferred.


r/gunsmithing • • 2d ago

DIY Shotgun Buttplate Ideas

Thumbnail reddit.com
0 Upvotes

r/gunsmithing • • 3d ago

Is it doable to turn my Winchester 1897 clone made by Norinco to it's trench gun version fitted with heat shield and bayonet lug?

Post image
49 Upvotes

r/gunsmithing • • 3d ago

what is this on the top of my colt carrier?

Post image
2 Upvotes

r/gunsmithing • • 3d ago

Do I need a gun smith for my Zavasta M70?

Thumbnail
gallery
11 Upvotes

Hello all, trying to get my Sandman X to center. When I tighten it down all the way the rod looks as if it’s touching or barely touching. When I dont it looks perfect. My question is the little bit of material on the lower front block needing to be removed or should I just take it to a gun smith?


r/gunsmithing • • 3d ago

Reputable smith to thread a R95

Post image
6 Upvotes

I do not have a competent gunsmith near me (KY). I’ve exhausted many “gunsmiths” local to my area. I can do better work in my 10x16 building than these hacks.

Who is trusted and reputable that I can ship my rifle off to to have it threaded 5/8x24?


r/gunsmithing • • 3d ago

With the nfa stuff

0 Upvotes

I’m a student in Machining. I’d like to get my hands on a 556 suppressor print does anyone know where I’d find one? Or do I need to make my own?


r/gunsmithing • • 3d ago

Psa dagger compact

Post image
0 Upvotes

This fell out of my dagger when I took out the back plate and firing pin I put it back together now it doesn’t want to slide on the frame is my slide broken now is this fixable ?


r/gunsmithing • • 4d ago

Hush puppy-fying

Thumbnail
gallery
32 Upvotes

Hey guys I just picked up a SW459 for 500 beans today and I was wondering who your recommend for a trigger job and adding the small cut and adding a slide lock to my pistol. I plan on getting a Greg’s grips threaded barrel for this


r/gunsmithing • • 5d ago

Norinco SKS found at LGS. Looking for professional opinions

Thumbnail
gallery
31 Upvotes

For context been looking around every now and then for a Norinco whenever I'd visit some shops in the area. Today I stumbled upon this - a triangle 26 Norinco w/ a fixed mag and supposedly all matching serial numbers and a sling for $550. Outer barrel and other metals look to be in good shape, but the bayonet is missing.

I asked one of the employees if the bore and firing pin had been inspected and he told me "yep, everything is good to go." The guy let me take some pics for doing some research before I decide to grab it up. Another older fart show me that it had a threaded barrel instead of pinned - claiming that threaded was the better variant. I ALMOST walked out with it but I hesitated since I couldn't check the bore without literally staring down the barrel, couldn't confirm whether threaded was superior to pinned based on my limited knowledge at the moment and blanked on exactly how to check the firing pin myself.

I'm no gunsmith, and this is a shot in the dark. If this post doesn't quite meet the sub rules, feel free to delete.

I definitely wanted to see what you guys think about the condition and whether the serial numbers/parts look original. As well anything you could say about threaded vs pinned, whether the condition is worth this buy for a range toy every now and then without being able to check the bore/firing pin assembly myself. Trying not to kick myself for not getting a full rifle pic, but I at least hope you all get the idea. I understand there probably isn't too much you could infer just from pictures alone, but even still just some common advice would be appreciated for how to approach the shop if I go back and want to inspect/have it inspected for safe functioning before I buy it

Thoughts? Opinions?


r/gunsmithing • • 4d ago

Brighten white steel

Post image
1 Upvotes

Is there an easy solution to remove rust staining from white steel? Im trying to turn this shell lifter bright white again.