r/gunsmithing • • 21h ago

Restoration Help

Thumbnail
gallery
21 Upvotes

I have a 1914 Ranger Model 235 (I think thats the right model) it was found in a crawlspace with a whiskey still but it has this bit of wood missing. I dont have the wood and dont know how I could best go about fixing it. I have wood epoxy but idk that thats the best solution.


r/gunsmithing • • 1h ago

Star Wars, Likelihood a smith can do this?

Thumbnail
gallery
• Upvotes

So I would like to print a dc15 or dc15s and drop in a 22 assembly.
What is the likely hood a smith would have a setup to drill accurately into the “barrel” of the 3d print, and cut a slot for the receiver and trigger assembly?
I know you guys probably have lathes and mills but not sure on how this could go.


r/gunsmithing • • 6h ago

Should I free float an old Weatherby with factory fore end pressure pad?

Post image
7 Upvotes

I'm having a heck of a time getting any consistency with this old 1991 manufactured, Howa built MkV 30-06. Tried a variety of factory ammo from 165gn to 200gn, tried some hand loads that shoot well in another rifle, checked the torque on the rings, am using a known good scope, and most recently, bedded the action. I'm still getting flyers, and i do mean flyers. It will put down a solid group and then a shot 4" off at 100. This is across all ammo tried. I never do long strings of fire. And the cold bore shot is usually poor, which doesn't lend itself to being a hunting rifle. Shots 2 and 3 are usually the best. Any more than that without cooling the barrel and it goes to pot. And before anybody asks it's not me flinching. I take several rifles to the range with me to shoot while the next one cools and my 280 Remington which weighs 4 lb less than this one kicks harder and I'm still putting down groups that touch. All of this is being done in a very solid bench rest setup.

So.... should I try adding some shims and see if it needs more pressure? Or is it time to bust out the Dremel? I'm not trying to make this 35-year-old rifle into a sub MOA tack driver. I know that will probably never happen. But it would be nice to get consistent inch and a half or even 2 in groups. I don't know if free floating it is just going to destroy it because the barrel is so thin but at this point I'm definitely willing to try different ideas.


r/gunsmithing • • 4h ago

RMR footprint mount on a SxS?

3 Upvotes

I am looking for someone that can cut out a portion of my cz bobwhite rib and weld/solder in a low profile RMR footprint plate. Does anyone have suggestions on who to reach out to that might take this on and do quality work? I


r/gunsmithing • • 8h ago

Stolen gun damaged

Thumbnail gallery
3 Upvotes

r/gunsmithing • • 21h ago

Uberti 1873 lever gun failing to feed .38 even over 1.5 oal. Potential modifications I can make to get most .38 to feed?

Post image
3 Upvotes

r/gunsmithing • • 7h ago

Stuck Mag Release on TortTort Receiver and Arsenal Kit

Thumbnail gallery
2 Upvotes

r/gunsmithing • • 11h ago

Cobray M-11/9 twitch FRT

1 Upvotes

I recently picked up a closed bolt Cobray M-11/9 and I wanted to pick up an frt for it. I was heavily considering the twitch frt, but was unsure if it would reliably work in this platform, as it is meant for the MPA defender. I saw one specifically made for the original cobrays from Advanced Reset Tech, but it is very expensive and I don't feel like dropping $264 dolans on a toy.

Basically, my question is this; Does anyone know if the twitch frt will work in an original Cobray M-11/9 or will it need fitment? I am fine with fitting it, just need to know what it would need.