r/handtools • • 4h ago

Tool Wall

Thumbnail
gallery
173 Upvotes

I may seriously have too many tools. Just finished my tool wall in my new shop. Lol


r/handtools • • 7h ago

Home made shooting plane

Thumbnail
gallery
170 Upvotes

Veritas blade/adjuster. Beech body. 8mm brass sole for weight.

The body is made from 2 cnc machined halves, aligned with dowels.

The handle is hand carved and simply glued to the top.


r/handtools • • 23h ago

How do I read this inside diameter correctly?

Thumbnail
gallery
139 Upvotes

Hi everyone, today I wanted to measure the inside diameter of this hole. I positioned my caliper, but now I'm really unsure if the hole is 30mm or 35mm wide. Can someone explain to me exactly how to read this scale?


r/handtools • • 19h ago

Vernier Calipers Explained

Post image
86 Upvotes

Lots of people seem to struggle with the concept of a Vernier scale and therefore don't know how to read a Vernier caliper.

That's not really a problem in most people's lives as: 1 - digital calipers are cheap and readily available, and 2 - most people don't need to measure to tolerances of 0.1mm or less.

For those who do need that level of accuracy, and don't want to rely on battery powered tools, learning to read a Vernier scale is useful. For those who don't, it's still a fascinating bit of maths.

Vernier scales work in incremental differences : each gap on the Vernier scale is 0.1mm shorter than a gap on the millimetre scale. So every time the jaws open another 0.1mm, the next Vernier mark along comes into line. Everything else follows from that.

The increments can be very small (most metric calipers read to 0.05mm or 0.02mm), but let's keep it simple and use an example where we want to measure to the nearest 0.1mm.

On the top half of the caliper, we have a coarse scale, marked in increments of whole millimetres - 1mm, 2mm, 3mm and so on. On the bottom half, we have the Vernier scale, marked in increments of 0.9mm - 0.9, 1.8, 2.7 and so on. We only need ten of these, the first being the zero mark.

Imagine the calipers are closed, measuring zero. The zero mark on the Vernier scale lines up with the zero mark on the millimetre scale, but none of the others do. The first Vernier mark is 0.1mm short of lining up with 1mm, the second is 0.2mm short of lining up with 2mm, and so on.

Now imagine we measure something that is 0.1mm in thickness. The jaws are now 0.1mm apart, and the sliding part with the Vernier scale on it moves along with them. Now the zero mark doesn't line up any more, but the first Vernier mark, at 0.9mm, now lines up exactly with the 1mm mark. Measure something 0.2mm thick, and the second Vernier mark will be in line with 2mm.

The mathemagical part is that this works exactly the same as the distances get bigger. It doesn't matter which mm mark the Vernier mark lines up with, only which Vernier mark it is.

To read the scale, we look at the zero mark first, and find the last whole millimetre it has passed. Not the nearest one - if the zero is sitting at 7.9, we still start from 7. If the zero lines up perfectly with that millimetre then we're finished, the measurement is 7.0mm. If it's a bit past, then we go along our Vernier scale looking for the closest alignment. If the first Vernier mark lines up with a mark on the mm scale, the measurement is 7.1, if the second lines up, it's 7.2 and so on...

So, for example (as in the picture), if the zero has passed 7, and the third Vernier mark lines up with a mark on the mm scale, the measurement is 7.3mm.

If the zero mark is closer to 8 than it is to 7, you know the answer is 7.5 or more, so you can skip straight to looking for an alignment in the second half of the Vernier scale.

Many calipers read to 0.05mm or 0.02mm, and some also stretch the Vernier scale out to make the lines easier to tell apart, so yours might not look exactly like this example. The principle is exactly the same.

That's all there is to it. A beautiful, simple, somewhat counterintuitive bit of maths that allows us to quickly and easily measure down to tolerances so small we almost can't see them.


r/handtools • • 5h ago

Plane and saw till

Thumbnail gallery
65 Upvotes

r/handtools • • 50m ago

Since We Are Posting Tool Storage

Post image
• Upvotes

Temporary accumulation of random boxes I’ve built as prototypes for classes at our store - and some halfassed chisel/marking/measuring racks.

The plane till was originally just an open wall cabinet meant to get a door and back but I repurposed. Not a perfect fit for the collection. I’m planning a bigger better cabinet but time is always the limiting factor.


r/handtools • • 16h ago

A couple wooden body hand planes I finally got around to fully restoring

Thumbnail
gallery
41 Upvotes

I really only have time to restore tools nowadays, for the time being. I repaired these over a few early morning shop sessions.

I'd gotten these to usable condition previously, but the tops of the cheeks had split out as so many do. The left cheek coffin smoother split way further down and toward the bed, as pictured. I always make the inlaid cheek repair wider at the bottom so that it resists breaking again when the wedge is driven in

I've done enough of these that I don't even need to fully measure/mark the layout, I just get to chiseling and square them up as I go as far as marking goes. When you find a wooden body plane that has been re-mouthed, often times it's not symmetrical, as an example.

A tip on re-mouthing, the usual tradutional way, make the sides pointing toward the rear of the plane the width of a wider chisel you have. You can keep adjusting the angle of the sides with more chisel strikes until they meet. I'd just made this one all the way across because this was my 2nd re-mouth, because it was easier. Don't be afraid to get to chopping away at these planes, because they're wood you can always repair them.


r/handtools • • 18h ago

New Handle for Knew Concepts

Post image
19 Upvotes

I always wanted to turn a nice handle for my 8” Knew Concepts Mk III fret saw, but never got around to it.

I recently figured out the 8” wouldn’t fit in my (yet to be built) tool chest trays, so I picked up a 5” Mk III the other day.

Turned a new handle Sunday night in curly maple, finished with a few coats of Tru-Oil, and now it just needs a tray to rest in!


r/handtools • • 21h ago

Next plane?

15 Upvotes

I was/am interested in a no.4 for its versatility and to primarily use for smoothing. I purchased a vintage Stanley Bailey no.4 on eBay but was sent a no.3.

I kept the no.3 after getting a partial refund, and like it as a smoother after more or less fully restoring it, but want something to flatten boards and small/medium glued up panels, and for general rough work. Would a no.5 be the logical next one to get, instead of the no.4 that I wanted in the first place?

I’m making a 1-1/2 seat garden bench and I’d like to challenge myself by prepping the parts from the rough sawn lumber I’ve already purchased with a hand saw and plane, instead of my table saw and planer. I’m also interested in ripping and jointing stock for medium-sized edge grain cutting board, to see if I can do it by hand. Over the winter it’s easier for me to work indoors, and I want to keep noise and dust down without putting a pause on my projects.


r/handtools • • 2h ago

Mallet splitting

Thumbnail
gallery
13 Upvotes

Hello! I recently made my first “real mallet” from false acacia, and after a couple weeks it started splitting. Is this an issue with the wood species? Or just a “skill issue” with how I made it? Any help is appreciated


r/handtools • • 3h ago

Good deal?

Post image
6 Upvotes

These popped up in my area (middle of nowhere).

$50 for the pair, no info on them. Can anyone with more expertise tell me if these are any good? This is the only photo as well.


r/handtools • • 22h ago

Advice wanted on sweetheart era Stanley hand plane knob and tote restoration

5 Upvotes

I recently got a few knobs and totes I'd like to restore, but I'm still new to this. Much of the original finish is intact on them, but the clear coat on them is not completely intact on any of them, and for some there's only tiny patches left. There also seems to be dark build-up of some sort on the top of the knobs. I want to remove the clear coat (and that dark build-up) and even out the color without removing a ton of the original finish, as well as fill some of the holes where the grain meets the surface, but all the restoration videos I see online are just "sand the whole thing and cover it in BLO." I want it to look very visually clean and accurate as I can to new (of the time it was made) without completely destroying the history of it and removing the parts that survived. Recommendations?


r/handtools • • 1h ago

Owners/users of ECE Primus smoothers - what do you think of them?

• Upvotes

For context: I have a good Stanley #3 and #5, but between them, all I have are an Ulmia wooden smoother (hammer-adjusted) and a low-quality Garret Wade #4 that I'm fed up with. I enjoy using the woodie, I love the grip, and I know how to adjust it - but I also know myself well enough to understand I'm never going to just be perfectly fine with it. I often have very limited time to do work and I consciously invest in ways to make that time more enjoyable, and tapping an iron several times to fine-tune the settings just isn't what I'm here to do. But I'd still like something larger than the #3 for day-to-day use, and I can afford to 'splurge' on a new plane for this purpose. I'm going back and forth about options and a Primus smoother is a possibility. But unlike, say, a LN or Veritas there aren't a ton of straightforward reviews.

So - if you've got one of these Norris-adjusted fancy wooden planes, or you've had a lot of hands-on experience, how do you like them? Would you recommend them as a primary smoother for a 'typical' American hand tool shop, making small-to-medium furniture in (mostly) walnut, cherry, oak, and other North American domestic lumber?


r/handtools • • 6h ago

Laminated handles?

3 Upvotes

Is there anything inherently wrong with making handles (here thinking specifically about mallet handles, maybe axes too) out of multiple glued pieces? Are there extra considerations to take if I go down this route?


r/handtools • • 14h ago

Jackpot?

4 Upvotes

Anybody in the NYC/Lower Hudson Valley might want to check this Craigslist listing.

https://www.craigslist.org/view/d/yonkers-wood-working-tools/itV2CS3P4ApzuLurbzyjG2

Hope this is useful to someone.