r/openwrt • • 6h ago

bridged access point? [eli5, noob]

Thumbnail openwrt.org
1 Upvotes

I've used these instructions to configure a second router (B), to connect to a existing wifi (A).

What I want is for (B) to be isolated from (A), so that devices connected to (A) cannot see or use devices connected to (B). Almost as if (A) was the guest network, unable to use printers or NAS in network (B).

Is this a suitable way to do that? How could I test if (B) is properly isolated?


r/openwrt • • 7h ago

Cudy WR3000P (SN 2624) – WAN port dead / not recognized on OpenWrt, forcing LAN fallback. Any fixes for newer hardware revisions?

1 Upvotes

Hi everyone,

I recently installed OpenWrt on my Cudy WR3000P v1 (EU version), specifically unit with serial number starting around 2624.

As known from some other Cudy/MediaTek devices, the 2.5G WAN port (which also handles PoE-in) is giving me a hard time. On a fresh OpenWrt installation (25.12.5), the WAN port remains completely dead—no link, no reaction to the cable, and dmesg | grep -i eth shows no eth interfaces at all (only the internal switch and wireless interfaces).

Right now, I am forced to use a workaround by using LAN 1 as a fallback WAN port, which works fine for data. However, since the WR3000P supports PoE, I really want to get rid of the separate power cable and use the actual WAN port to power and feed the device cleanly.

  • What I've checked:

    • dmesg shows no signs of the 2.5G PHY being initialized properly (likely a Clause 45 / Realtek PHY / MediaTek bridge initialization issue similar to other RTL8221B / MT7981 reports).
    • Given the newer serial number (2624), it seems like a silent hardware revision update from Cudy where the device tree might need an update.

Questions:

  1. Has anyone with a newer Cudy WR3000P revision managed to get the 2.5G WAN port working?
  2. Are there any specific patches, custom DTS tweaks, or kernel flags required for these newer board revisions?
  3. Would jumping to a very recent master snapshot fix this, or is it a known pending issue?

Any advice or pointers would be greatly appreciated!
Thanks in advance.


r/openwrt • • 1d ago

I got my OpenWrt APs to show up as UniFi APs in the controller. It mostly works, and I need help testing it on hardware I don't own

45 Upvotes

Hey all,

So I have a UniFi gateway at home (UCG Ultra) but I didn't want to buy UniFi APs when I already had perfectly good routers running OpenWrt. I found jonasevcik's openUF project, started poking at it, and over the last few months it turned into my own version that I now run on both APs in my house.

Repo: https://github.com/yesrab/openUF

What it does right now: the controller adopts the OpenWrt box like it's a U6 In-Wall, pushes my SSIDs, VLANs and radio settings to it, and shows clients, signal and traffic like it would for a real AP. Fast roaming, band steering, min RSSI, speed limits, and client block/unblock work for me. There's also a small LuCI app and an installer script.

What I'm honestly not sure about, and where I need help:>

- I've only really lived with it on JioRouter AX6000 (mediatek filogic) and tested on a couple of old TP-Links (Archer C5 v1, WDR3500). If you have something else and an afternoon, I'd love to know if it even adopts.

- I don't own a single real UniFi AP. Roaming between openUF and genuine UniFi APs is done through d-malinowski's plugin and I'm trusting his testing, not mine. If you have a mixed setup, you're exactly who I need.

- Guest portal, rollback when a config push breaks wifi, encrypted syslog to the controller, and device SSH login were added recently and have only run in a VM. They're off by default for that reason.

- It needs about 16 MB flash. 8 MB devices don't fit the crypto library. If someone knows a clean way around that I'm all ears.

I'm not a networking pro, so if you look at the code and think "why on earth did he do it like that", please tell me. Issues, PRs, or just "it broke on my X" are all welcome. A lot of what's in there came from other people already (jonasevcik's original, d-malinowski's roaming work, and antoniocosta's unifi-openwrt, which was posted here recently and does the same thing in Go).

Not affiliated with Ubiquiti, it never flashes their firmware, and it's GPL.

Thanks for reading. Happy to answer anything.


r/openwrt • • 1d ago

The current Mbed TLS developers are looking for new maintainers to succeed them. Otherwise, they'll abandon their TLS and X.509 libraries in April 2027.

Thumbnail lists.openwrt.org
82 Upvotes

r/openwrt • • 20h ago

Old-school install clarification

1 Upvotes

I just picked up a WRT54G V2.0 for like, nothing. Yes yes I know this is ancient and considered EOL in latest releases, but I only plan to use it as an extra 802.11G network and I had a lot of success with these devices some years ago and it's not like they've broken in the meantime.

The wiki seems to have gotten a little confusing on these older devices -- it says the latest installable version is 19.07.10 but then starts veering into discussion of 10.03.1 in the actual install instructions, while sort of having multiple edits debating the correct procedure in the article text...and a mention of having to install a 2.4-kernel based image before upgrading to brcm47xx which I'm not sure whether really applies or not...it all just seems to have bit-rotted a tad, does anyone still mess with these devices to clear things up?

https://openwrt.org/toh/linksys/wrt54g?s%5B%5D=page


r/openwrt • • 2d ago

Where can I read about how to set up a LUCI statistics plugin definition?

4 Upvotes

This page has some information that I believe got me pointed in the right direction for making the data readable by RRDtool, but now I think I have to figure out how to tell RRDtool what graphs I want, and I can't find any actual documentation on how to do that. I know I need to put something at /www/luci-static/resources/statistics/rrdtool/definitions/exec.js and there are other examples in there that give me the general shape of the file, but I can't figure out how it works just from reading the examples.


r/openwrt • • 3d ago

Meraki MX100 opnwrt router

8 Upvotes

I found a cheap Cisco Meraki MX100 on Facebook should I buy this and install openwrt. On website it says it’s a generic installation how hard is this installation I assume it’s easy.


r/openwrt • • 3d ago

[Part 2] Rescued my Soft-Bricked my ZTE ZXHN F670L - Just to fall into another rabbit hole

Thumbnail gallery
34 Upvotes

Hey Guys,

Surprise Surprise, Now I'm porting openwrt to ZTE F670L.

[Short Summary]

I was able to rescue my soft bricked router using TFTP upgrade method. But soon found out that changing anything in rootfs causes crc error and bricks the device.

So, I'm adding this device's support in openwrt and use for my usecase, which was to share mobile internet using Eth Tethering.

Current Progress?

  • Flashing using TFTP
  • System Boots
  • Both 2.4 and 5 Ghz WLAN work
  • Able to access the LuCi Dash

[Long Story]

  • After getting the UART serial reader, I tried many combinations but was getting gibberish data, similar to what other people have seen with ZTE routers.
  • I was able to read the Serial logs by using USB metal housing as GND.
  • Could not two way communication to work, but from the logs and tinkering with the reset switch, I got to know about TFTP upgrade mode.
  • Luckily found "V1.1.20P3N6B" firmware and unbricked the device
  • Upon customizing again, I found that changing anything in rootfs causes CRC check error and bricks the device.

This caused me to abandon the stock firmware and try porting openwrt for this.

Why openwrt? Idk, I'm new into this and I knly know about this rn.

As of now, I am able to

  • Successfully flash and boot into openwrt firmware.
  • Start both 2.4 and 5 Ghz Wlan
  • Started with a custom html page served using httpd but now Luci dashboard is being served correctly.

Current target is to get LAN to work. Post which my usecase can be achieved.

I'm mostly vibe-coding my way through this, so I'm not sure I'll be able to answer any question, if someone asks. Pls expect a AI paraphrased response.

I'll also add the Agent's work summary in comments.


r/openwrt • • 3d ago

Change the WAN-Ports Mac-Address

1 Upvotes

With my Fritz!Box 7530 AX running the default firmware, I was able to get a new public IP address after a reconnect. This no longer works with my Fritz!Box 7520 running OpenWrt, and in Network > Interfaces I see a CGNAT IP. I found out that this might be caused by the router's MAC address, so I want to change it to the MAC address of my old Fritz!Box.

When I click 'Edit' on the WAN interface, under 'General Settings', there is an option called 'MAC Address'. When I enter the MAC address there and restart the WAN device, the connection drops and won't come back up. There is no other field to change the MAC address. How can I fix this?


r/openwrt • • 4d ago

Suggestions / recommendations for my next router - please

12 Upvotes

Hi all,

TL;DR - I'd really appreciate your recommendations for a router that has dual 2.5Gbe NICs and happily runs the latest OpenWRT.

My x86 machine that was running as a router has died, the Linksys WRT1900ACS is running for now, but my Internet connection is 2Gbps and I'd like to use it.

Requirements - pretty simple:

  • Minimum of 2 x 2.5Gbe NICs for connectivity
  • No WiFi needed (it will be switched off because I have access points with a wired backhaul)
  • Minimal 'power': I used to use SQM, but at some point during a rebuild I lost it and never re-installed.

    • My existing Linksys WRT1900ACS reports only 25% of the 512MB RAM is in use
  • Installed services:

    • Adblock
    • HTTPS Dns Proxy
    • Tiny Proxy
    • Policy Based Routing (to route some traffic via a Wireguard client interface)

Options I've looked at so far:

Are there any others I should consider?


r/openwrt • • 3d ago

Meraki MR42. Has anyone been able to flash OWRT recently?

1 Upvotes

I have a couple of decomissioned MR42s from work that were going to go into the landfill. I grabbed them and I thought I would flash OpenWRT on them. I read the guide and tried the "diagnostics mode" first without opening up the box first and no matter what I tried, it just wouldn't work. Next step is serial/UART. Well, I opened up the box and connected RX, TX and GND (at 3.3V, but didn't connect 3.3v pin) from my waveshare UART adapter (that has worked many times before on different devices) and there is no output from the serial. AT. ALL. (adapter has LEDs for RX and TX that usually blink on activity - there is no activity, no blinking at all) I tried different combinations of RX TX, different pins, cleaned the contact pads etc. There is no output. The adapter itself works if I connect RX to TX. Does anybody know if Meraki disabled uart in recent firmware updates? These MR42s were in use up until very recently (we are talking weeks, not months)

EDIT: I should also add that Meraki cycles throguh different colors on LED so it seems to be working normally. I am also 100% certain I never connected to pad #1 with a triangle on it as I was very careful with that


r/openwrt • • 4d ago

Help troubleshooting very slow wifi speed on GL-MT6000

Thumbnail gallery
7 Upvotes

I've had issues on and off since I flashed the GL-MT6000 with OpenWRT.
If I plug directly into the MT6000 via ethernet, I can download this ~300MB file in 1-2 seconds, joining wifi over both 2.4GHz and 5.0GHz, it is taking 15+ minutes.
I checked my channels for interference and width for both 2.4 and 5.0 and they are good. I toggled Hardware flow offloading and enabled WMM Mode.
Not sure where to begin troubleshooting.
Any help would be appreciated.


r/openwrt • • 4d ago

Meraki MR33 upgrade to openwrt

4 Upvotes

I bought a Meraki MR33 and uboot is from 2017 so looks I have to go the long way. Is any new way to get Openwrt without jtag.


r/openwrt • • 5d ago

OpenWrt access points as UniFi access points

70 Upvotes

Google turned the OnHub into abandonware in 2023. OpenWrt revived it, but I run a UniFi router, which only likes to manage Ubiquiti's own APs.

So I wrote a small daemon that speaks UniFi's inform protocol: The controller adopts the OpenWrt AP as a real UniFi model and manages its Wi-Fi, clients, stats, roaming and mesh like its own.

So far it's only tested on that one device, but it would be cool to hear from people with other hardware running OpenWrt.


r/openwrt • • 6d ago

What's your experience with OpenWrt on the ASUS RT-AX89X (rev. B2)

5 Upvotes

Hi, I've just found out that I could replace my router firmware with OpenWrt, which will allow me to use MAP-E, that's necessary to connect directly to the ONT that my ISP will provide me with if I change my contract to the "self-bought router" option. With this I'll be able to take advantage of the full 5 Gb/s that they provide, without being limited to the 2.5 Gb port of their stock router, that I'm using in ONT mode atm.

I've also seen that the B2 will be flawlessly compatible with NSS hardware acceleration, but I don't know much about it. I've also read about possible 5 GHz instability with this firmware, so this is kind of holding me back since I got this router to extend the Wi-Fi range without having to buy extenders (mesh extenders don't work natively on the ISP router, only as access points).

What's your experience with that? Thank you in advance!


r/openwrt • • 6d ago

Wan instabillity

5 Upvotes

I have a Flint 2 which has been running GL-iNet firmware for a year.

I decided to have a play with Openwrt again and installed 25.12.6 and instantly my WAN has been very unstable. I did use 24.10 last year without any issue.

My Flint is connected to a Virgin Media Super Hub 5 via Cat6 to a 2.5Gbe WAN port, which is running in modem mode. The Flint is doing the routing.

I keep getting packet loss and wan disconnections. From what I can see from the logs, it looks like the cable modem is not responding to DHCP requests quick enough and the Flint's WAN is blipping causing all traffic to cease.

How can I prove the WAN port is either faulty or blipping?

The cable modem is fine. I have directly connected a PC into it and there is no packet loss or instability.

I have tried going back to GL-iNet firmware and Tomato64 too. Tried a different patch cable. I get the same result!


r/openwrt • • 6d ago

Help with WAN configuration

3 Upvotes

I'm attempting to switch over my ISP provided Wifi router to a OpenWrt One wifi router because reasons... Anyway this is where my knowledge gap is showing the most because I can't figure out what I'm doing wrong.

The set up normally is as follows, An ISP provided Modem to an ISP provided Wifi router gives us internet as expected. When I attempt to switch the Routers out, we get no internet.

As far as configuration goes the LAN port is able to make connection with the PC and will give it an IP address via DHCP. I can access the web interface no problem. Connecting the Modem to the WAN though is where I have a major knowledge gap on how this all works. No IP address gets assigned to the WAN interface ( Which okay if the Modem doesn't handle DHCP ). But manually setting an IP address doesn't change anything either ( Probably because Im doing it wrong)

The only time I can actually route traffic through the Openwrt One router is by running a line from the Old Wifi Routers Ethernet Panel, to the Ones WAN port. When I do that, then an IP address will get assigned to the interface and the router will have internet activity.

I would expect just connecting the modem to the WAN would just work. I couldn't find any post with this exact problem and would really appreciate any help. Thank you.


r/openwrt • • 7d ago

Soft-Bricked my ZTE ZXHN F670L while tinkering - And I couldn't be happier about it

Thumbnail gallery
32 Upvotes

Hey guys,

First-time poster here.

[Short Story]

I just soft-bricked my router while customizing it to use unlimited 5G over USB tethering. And now I'm here waiting for the USB to UART converter to try and unbrick it via the serial console.

Having a blast playing around with these.

[Long Story]

I just wanted to play around with openwrt to figure out if it fit my usecase for using my Unlimited 5G data in my setup.

Since there is no support for ZTE F670L, I decided to customize the stock firmware directly:

  • Unlocked and connected via telnet.
  • Setup a SSH server for easy access.
  • Configured to route via the Ethernet port.
  • Reverse engineered led key libraries to control the front LED indicators.

While on last step to turn off the red blinking light (since fibre is unplugged), I soft-bricked it and now it stuck while booting.

I did find the UART serial pins and ordered a USB to UART converter to rescue this.

Rescue should work, since I made backups at every step. But even if it doesn't, it was so fun to play around with this.

See you guys after the rescue operation.


r/openwrt • • 7d ago

Issue with VLAN

3 Upvotes

Hello, I'm trying to separate some VM's into their own VLAN, but the VLAN i created doesn't seem to work. On the LAN1 port i want all clients to connect to my LAN, except ones set to use tagged VLAN 10 id. Currently all untagged clients can connect to my LAN normally, but when i set VLAN 10 tag on them they don't receive an IP address and even if i set it manually they can't ping the gateway. I have tried making VLAN 10 untagged and default VLAN but the same thing happens so I'm guessing something is wrong with the interface configuration.

EDIT: I somehow didn’t see that firewall zone was misconfigured and was blocking everything. After correcting that everything works fine.


r/openwrt • • 9d ago

Openwrt on raspberry pi5 in container

10 Upvotes

Hi! I want to install openwrt on my raspberry pi5 and use my router as an access point. Both will be connected to a switch with VLAN. Fibermodem is connected to pi5 ethernet port and traffic flows out to usb 3.0 ethernet adapter to the switch where I have devices connected to ethernet and devices on my wifi access point.

Anyone tried something like this with openwrt in a container/docker?


r/openwrt • • 10d ago

what convinced you to switch from gl inet firmware to openwrt?

33 Upvotes

is there any benefit to doing that for an average person? I don't know what exactly the difference is between the latest openwrt luci and the luci i can log into already, but im interested in optimizing everything for maximum security and more privacy


r/openwrt • • 10d ago

LobbyFence – free, open-source geo-filter for OpenWrt, FreshTomato, Asuswrt-Merlin and DD-WRT routers

28 Upvotes

https://forum.openwrt.org/t/lobbyfence-free-open-source-geo-filter-for-openwrt-freshtomato-asuswrt-merlin-and-dd-wrt-routers/255313

Just making people aware that there's a new geofilter alternative. I am the guy that made it compared to others; I would argue it is superior in every aspect, though feedback is greatly appreciated.


r/openwrt • • 10d ago

I got a spare Airtel router which is locked. Titanium 2122A

2 Upvotes

So, basically I have a spare Airtel router, and its software is locked. Is there a way to get the full access, both the backend and the UI. If changing the firmware is possible then I would consider it.
So is there anyway?


r/openwrt • • 10d ago

Netgear Orbi RBK20 + OpenWRT: Is it worth?

4 Upvotes

Hello,

I have an RBK20 kit (one RBR20 and two RBS20 satellites) from 2018 running the latest firmware: 2.7.6.6.

Is it worth installing OpenWrt on it? Will this break the mesh functionality? I have seen conflicting information—some say it breaks the mesh, while others say it can be configured to work properly.

Also, considering the outdated hardware, are there any real advantages to doing this? One feature pushing me toward making the switch is WireGuard support.

Thoughts? Any feedback is very appreciated!