r/printers • • Dec 19 '24 Bravo

Discussion The truth about printer subscription programs and many misconceptions about them

154 Upvotes

Dear all,

I work in the printer industry. For a very well-known consumer products manufacturer that gets discussed on this sub a lot.  I will not disclose which manufacturer I work for, nor will I disclose any manufacturer I do not work for (since the industry is relatively small eliminating 1 or 2 will make it generally too obvious as to which I do work for) as I am not officially speaking on behalf of the company. But, I want to set the record straight on subscription programs because some of you are drastically misinformed and it is very frustrating to see as someone who understands these programs as well as basic logic.

There are two types of subscription programs. Each of the major consumer manufacturers offers at least 1 of these programs, some offer both.

The first type of program is an auto-reordering program. The printer can tell (via various ways depending on each manufacturer) when the ink / toner is low and when it hits a certain point that will trigger an order of the ink/toner that device uses. Most manufactures that offer this will first send you an email letting you know that an order has been triggered and it will allow you to skip the delivery of the consumable and thus not get charged. If you allow the order to go through you are purchasing that consumable. That consumable is yours, you own it, just as if you walked into a Staples, Office Depot, Best Buy, or bought it on Amazon… You can cancel the “subscription” the next day and continue to use that consumable until it is empty.

The second type of program is a true subscription program. **THIS** is what many of you are vastly misinformed and / or are irrational about. In this program *you are not purchasing a consumable* at all. You are paying the manufacturer for X number of pages per month. The manufacturer will send you a consumable to use because the printer needs ink / toner to work but, that is not what you are paying for. You are paying the manufacturer $Y per month to print up to X pages per month.. that’s it. Of course you can print over that X number and pay an overage (just like years ago with cell phones).. and of course, you can print under that X number and some pages will roll-over to future months (just like years ago with cell phones). The owner of the consumable is the manufacturer. You never bought it, you never owned it. Therefore, it is not yours to use after you end the subscription! The only reason most manufactures do not ask for it back is because they don’t want to pay for shipping it back to them. But, they still own it… not you.  You can think of this like renting an apartment. You are paying a landlord $X per month to live in their building. The landlord is providing the building for you to live in while you are paying rent. You do not own the building. and when you stop paying rent you are no longer allowed to continue living in the building. Just like your Netflix subscription, Apple TV subscription and Disney+ subscription.. when you stop paying for the subscription, you stop getting to use the service. Just because while you were paying you had access to the content does not mean you at any time owned that content and get to continue watching it once you stop paying the subscription.

I truly hope this helps clarify somethings for some of you. Others I understand are lost causes but, I will do my best to answer any questions I can.


r/printers • • 5h ago

Troubleshooting Hp smart is a scam

13 Upvotes

I have an hp envy 6458e printer and I’ve barely used it and I’ve decided to now use it.

It took an hour to get set up to the internet then I added it to the hp smart app which sucks so much to use because of the amount of ads.

I tried printing and it said something went wrong, I checked everything and it was ok.

I tried printing it again, same thing.

I checked it again and tried printing one more time and I get asked for a subscription.

I have no way of printing anything and every time I press the print button, I GET ASKED FOR A SUBSCRIPTION.

I changed the ink, I set it up to Wi-Fi, followed the instructions, and it still DOESN’T FUCKING WORK.

WHY DO I HAVE A PRINTER IF IT DOESN’T FUCKING PRINT

This is so frustrating because this is my only way to print things without buying expensive toner for my more professional one.


r/printers • • 3h ago

Discussion Laser Printer vs. Inkjet Printer – Which One Do You Prefer? 🖨️

4 Upvotes

Both technologies have their own advantages, but which one actually makes more sense?

  • Laser Printers: Fast printing, sharp text, and great for high-volume office work.
  • Inkjet Printers: Great for color printing, photos, and everyday home use.

If you had to choose one for your home or office, which would it be and why?

I'd love to hear your real-world experiences!


r/printers • • 1m ago

Troubleshooting I bought a thermal printer a while back and now that I’m using it, it doesn’t want to work.

Post image
1 Upvotes

When I first bought it I never could find the drivers for it but now I finally have but the only problem is seeing is that the printer will print just the top part and stop completely. Any help would be appreciated!


r/printers • • 2m ago

Other Best PAPER FOR EPSON 8550

1 Upvotes

I am printing some spiral coloring books and want to print 200-300 GSM matte paper cover for the books.

Any suggestions which paper to choose as their is so many options and also no options. So much confusion.


r/printers • • 1h ago

Troubleshooting Roller marks Epson ET8550

Thumbnail gallery
1 Upvotes

Hi! I have an Epson ET8550. I'm printing on 250-gram matte paper, either from the rear tray or the rear feed slot, and in both cases, these dark roller marks appear on the sides, which smudge the print. I've been searching online but can't find anything similar or instructions on how to clean the rollers. The printer is practically new—it has only 30 prints on it. Help—I don’t know what to do. I’ve already set it to “thick paper” in the menu. I need to print at “better” or “highest” quality, but no matter what settings I try, it always comes out like this.


r/printers • • 1h ago

Purchasing printer recommendations

1 Upvotes

hi!! I make lots of fun little crafts mostly just for me and friends. I’m interested in selling them though, I have a button maker, and I love making buttons but I’m not allowed to use the family printer anymore because I’m wasting the ink. I don’t wanna leave the house every time I need to print a sheet for a project, is there such thing as a printer I can buy that will print beautiful vibrant colors, that isn’t 1 million dollars and maybe doesn’t use up the ink so fast? I’m not looking for like glossy photos to hang up, but rather just regular matte paper printed photos but in higher quality and maybe using less ink than my HP envy. Thanks in advance!!


r/printers • • 2h ago

Discussion Warranty service Epson

1 Upvotes

How satisfied are you with the warranty service from Epson?

I bought a ET-2860 and realised I needed to change out one of the cartridges that sit above the print head because the previous owner had put the wrong ink into the black tank I did find the part on AliExpress but it would take 2-3 weeks to ship and that’s why I contacted Epson support, they said it was free of charge because it’s still under warranty. (The previous owner printed only like 8 pages and bought it recently)

Excited to hear your answers, please only people with warranty service from Epson.

Thank you:)


r/printers • • 4h ago

Purchasing Mobile printer with separate CMYK instead of tricolor+k?

1 Upvotes

Does anyone know of a mobile printer with separate color cartridges? I'd love to be able to on site print my invoices with my logos and color pallet to solidify my branding a little more. (Home reno contractor) My logo and color pallet is primarily cyan (think blueprint color scheme and black) and I'd be waisting 2/3 of normal tricolor cartridges. And if I can't find it I might just pre print templates with the blue and then print back on site. If it works out to be that much more cost effective.


r/printers • • 5h ago

Purchasing Artist seeking studio printer purchase advice

1 Upvotes
#What would you like to accomplish?

Sorry if I haven't filled this out correctly--I am an artist and writer who works a lot with printed text/image. I recently moved studios and no longer have access to a printer/scanner. I need one, but don't have a ton of extra cash to invest in something crazy (I'm used to being at institutions with free commercial and photo printers...alas). For myself, I want something reliable and relatively inexpensive to refill given the potential of high-volume printing. I don't need crazy photo capabilities, though decent quality would be appreciated. I am only printing text and occasional reference images. 

Not currently looking at any particular models, but seeing things come up on resell sites and having a hard time knowing what my parameters/criteria should be. 

#Minimum Requirements:

- Budget: $100-$200
- Country: France
- Color or black and white: Both
- Laser or ink printer:  not sure
- New or used: not sure/either (looking online & on resell/freecycle sites)
- Multi-function: Yes - want scanning also. 
- Duplex Printing: what is this ? 
- Home or business: Home/studio
- Printing content: High volume text pages (hundreds), some images 
- Printing frequency: Few pages per week, but some weeks could be a hundred pages
- Pages per minute : N/A
- Page size: A4
- Device printing from: Laptop 
- Connection type: I'd really like USB so I don't have to deal with Wi-Fi. I have terrible wi-fi at my studio and hate the experience of troubleshooting a printer... 

#Any other details:

I'd really like to get something that won't bleed me dry when I replace cartriges as I print a lot. But I don't need high quality images--when I need to print anything more than reference photos, I get that professionally done. I'm just looking to be able to print/scan in studio stuff that I am reading/working with. 

r/printers • • 18h ago

Rant HP stinks.

11 Upvotes

Bought a printer from a lady from marketplace and was so excited to see that the cartridges are over halfway full. Turns out they’re the instant ink cartridges so they are unusable since she had them through her subscription.

Knew I shouldn’t have gotten an hp but it was all I could find on marketplace where the seller was nearby and I felt safe meeting up with

So frustrated and feels so wasteful. I’m assuming they’re a lost cause, but is there anything I can do besides buy new ones?


r/printers • • 9h ago

Purchasing Lexmark

2 Upvotes

now that Lexmark has discontinued and end-of-support is just a few years away, is it a bad idea to get one of their printers?


r/printers • • 5h ago

Troubleshooting BIZHUB TONER BYPASS

1 Upvotes

How can I make a bizhub C284e think it has a full toner cartridge without even inserting a used one (i know its possible because my company have one)


r/printers • • 6h ago

Purchasing Leasing offer from KM - is it fair or overkill?

1 Upvotes

Hey everyone, I’d like your help to find out if we are being taken advantage of concerning the new printer model Konica Minolta is offering our tiny office of 2 people.

Since English isn’t my first language, please let me know if there’s anything I didn’t make clear or is hard to understand.

We have a leasing agreement with Konica Minolta (KM). Since our old printer – a bizhub 4020i – is starting to leave streaks, I asked them to please send us an offer for a new leasing agreement. For our current plan we are paying 50,29 € a month.

Firstly, KM told me, we don’t use our monthly amount of 500 pages. We only print around 200 pages per month (ppm). They asked if we would like to lower the ppm and I agreed to lower it to 300 pages.

They then sent me an offer for a bizhub 4051i, asking for 51,45 € a month although we lowered the ppm by 40%. I told them I can’t accept that offer since we’re getting less for more money and they came back to me with the same offer for 46,34 € a month.

Since that is lower than our current monthly rate, I’m basically fine with it but I don’t think we even need the 4051i?

I don’t know a single thing about printers, but I did compare the information I could find on the 4051i with the specs of a way smaller and less heavy device I would personally prefer the bizhub 4221i.

From what I’ve seen, the 4051i has way more RAM, prints faster and with better quality than the 4221i. We don't need that.

So, I asked KM why they would offer us the 4051i instead of the 4221i since from my perspective, 4221i is smaller, lighter and as we are not printing much, completely sufficient for out little bureau. I received the following answer from KM:

“The 4051i is our entry-level-model and the most economical solution which is why we have offered it as a follow-up for your 4020i (for which support / production of spare parts might end soon). [...] With the 4221i, we would already be moving up to a higher product and price tier within the portfolio."

They also added that the price is not based on “single hardware specs” but that it also “considers the platform, scope of application as well as it’s placement inside the product portfolio.”

So please let me know: Is the 4051i really the better and cheaper choice for us when compared to 4221i, or are they trying to take advantage of us?

I might still accept the offer since it is less than what we're paying now, but I am awfully curious tbh.

Thank you very much for your advice! <3


r/printers • • 6h ago

Other Hp Smart Tank 585

Post image
1 Upvotes

Alguien ha tenido problemas con los rodillos del papel en su hp?


r/printers • • 10h ago

Troubleshooting XEROX 3020 Chipless Firmware

2 Upvotes

Hello, I would need help with XEROX 3020

Suddenly the new replacable toners that i am buying are getting an error "toner not compatible" i owm a store and I would need help in this case, everybody is bringing out their printers and the issue is the same with the new toner cartridges, could anybody provide a fix or the chipless firmware, also all the customers that come to me will get a refund.

Help would be greatly appriciated.


r/printers • • 7h ago

Purchasing HP M283fdw – Peach 207X compatible toner with firmware 20211221: Any experience?

1 Upvotes

Hi everyone,

I own an HP Color LaserJet Pro MFP M283fdw (European/Swiss model), currently running firmware version 20211221, with automatic firmware updates disabled.

I'm looking for a more affordable alternative to genuine HP 207X toner cartridges and am considering the Peach 207X multipack (black, cyan, magenta and yellow). The price difference is substantial: CHF 180 (approx. $215) for the Peach multipack versus CHF 440 (~ $530) for the original HP cartridges, representing a saving of 60% (around $313) !

Product link:
https://www.galaxus.ch/fr/s1/product/peach-207x-m-c-y-cf-toner-21359314

I've contacted Peach directly, and they confirmed that their cartridges come with pre-installed chips, so there's no need to transfer the original HP chips. However, they couldn't guarantee compatibility with every firmware version due to HP's Dynamic Security system.

Has anyone successfully used Peach 207X cartridges with the HP M283fdw, or other alternative cartridges, particularly with firmware 20211221?

Thanks in advance for your help!

Al


r/printers • • 8h ago

Troubleshooting ET 8550 Error 000041

Thumbnail reddit.com
1 Upvotes

r/printers • • 8h ago

Troubleshooting How to fix bad quality :/

Post image
1 Upvotes

Hi guys, I recently got the Canon Pixma TR8620a printer and am gonna do my first artist alley !! I printed some stickers out on it and they came out pretty good, colors were nice and quality was decent. I test printed THESE photocards out in black and white and the quality was nice crisp. But when I went to print them out in color they were just dull and fuzzy 😭😭 i tried messing with settings and cant figure it out :c this is my first printer so if this is an obvious thing my bad but any help is appreciated :c


r/printers • • 9h ago

Purchasing This Inkjet Printer Worth Buying for a Student on a Tight Budget?

Post image
1 Upvotes

Canon PIXMA TS307, TS307A

I'm a student, and I really need a printer. However, I can't afford to spend much on an ink tank printer right now.

I'm looking for a budget-friendly option that will last at least 1–2 years with minimal maintenance. I came across this inkjet printer, and I'd like to know if it's worth buying or just a waste of money.

Would you recommend it for basic student use, or should I consider another option?


r/printers • • 9h ago

Troubleshooting SHARP MX 2651 Firmware

1 Upvotes

Colleagues, hello, who can share any version of the firmware for Sharp MX 2651


r/printers • • 13h ago

Troubleshooting just got an epsom et 2927 cannot find premium presentation matte on mac with driver

Post image
1 Upvotes

r/printers • • 14h ago

Troubleshooting printer prints yellow and magenta faint

Post image
1 Upvotes

- Printer Model: RICOH MP C2011
- Error Message: no error message
- Ethernet Cable, WiFi or USB: Ethernet
- Driver name and version: 1.04
- Firmware Version:
- OS: Win10
- # of machines impacted: 1
- # of users impacted: everyone
- Original or 3rd party cartridges: 3rd party

I tried the forced toner supply and it worked. I ran auto color calibration through the service menu: cyan and black passed, but yellow and magenta gave an error. I also tried the automatic color adjustment in the service menu, but it refuses to scan, probably because the color is too faint. I've already replaced the drum units and cleaned the laser with the special blue stick. The cartridges are new, and I shook them before installing


r/printers • • 15h ago

Troubleshooting Why clues why my printer is printing like this?

Post image
1 Upvotes

I just brought new CMY and black ink, and other images are coming out fine but for some reason the gingham is coming out all deep fried, I already ran a quality diagnostic report and it came back with flying colors.
For reference I have an hp envy inspire


r/printers • • 16h ago

Purchasing Brain swimming with choices on new Printer

1 Upvotes

What would you like to accomplish?
Want to choose a new printer. I’m a ‘crafter/maker’ do craft shows. Make greeting cards, stationary such as notebooks and planners, labels, signs, packaging.
Are there any models you are currently looking at?
I’m considering a refillable ink printer or laser. I sew with a Brother Machine, used a Brother Cut & Scan, I like their products. Not a HP fan, more towards Canon or Brother.
Minimum Requirements:
Budget: $400 or less
Country: US
Color or black and white: Color
Laser or ink printer: leaning toward laser if there is one that fits my needs
New or used: new
Multi-function: print only, no need for scan or fax
Duplex Printing: Yes
Home or business: home business for a crafter
Printing content: greeting cards, notebooks, planners, labels, packaging
Printing frequency: weekly
Pages per minute : more than what I’m getting now
Page size: small index card size to letter size
Device printing from: wireless, from computer or tablet
Connection type:
Any other details:
I’ve had $60 & $80 inkjet canons for the past 5 years without issue**.** Within** **Last year increased my creating/making and seeing efficiency is low and ink costs are high. I use paper weights from heavy card stock to copy paper of all sizes. I like a rear feed or a straight through pass for the heavier paper, if possible.

Let me know if you have other questions on my needs,
FYI - just ordered an Epson ET8500 impulsively which I want to return as I would prefer something a bit less costly and am anxious about issues with Refillable ink systems. Thank you for your time in helping me out with suggestions.