After nearly 5 years, the previous DC20V power distribution [setup][1] 300W power brick; ADL300SLC3A / ADL300SDC3A began to seem rather inelegant. It featured overly thin Y-splitter cables; 20 AWG—along with a multitude of unnecessary Slim Tip connectors. [BTW][2]
20AWG: OD 0.81 mm, cross-sectional area 0.52mm2, max 11A (20AWG transmission 1.5A)
vs. 14 AWG: 1.63 mm, cross-sectional area 2.08 mm2, 32–20 A (14AWG transmission 5.9A)
The power rating of a Lenovo power adapter is encoded within the connector pin [plug][3].
The power supply cables consist of a red core (positive) and a braided shield (negative). Shortening these cables requires soldering the braided shield. Do not coil the cables (as this causes heating).
The 15A adapter [female Slim Tip / female XT60][4] (measuring 36.8 × 18.5 × 8.2 mm) enabled the implementation of an XT60 distribution system (DC 0~150V, up to a total of 200A): connectors: 2 male & 4 female. In accordance with the convention for XT-series power connectors, male connectors serve as sinks (loads), while female connectors serve as sources (power supplies). XT60 Power Distribution Board [Total ~€29][5] (115 × 29 × 27.3 mm, 61 g).
- INPUT
- male -adapter 15A [Total ~€23] +Slim Tip 300W, 14AWG, 1.5m, brick DC20V15A 300W
- male -female_XT60, 14AWG, 0.1m; clamps; pigtail 15AWG, 1.8m, 230W, led, DC7450 + emergency power supply [Norsyee][6] NOR-12 station 232Ah /3.7V (4S LiPo) outlet DC7450 DC20V max17A (reserve +200Ah)
- OUTPUT
- female -m_XT60 14AWG 0.1m pigtail 14AWG, 1.5m, 300W Slim Tip +ThVx1 monitor 140W 7A
- female -m_XT60 14AWG 0.1m pigtail 14AWG, 1.5m, 300W Slim Tip +Tom (m920q) 40W 5A
- female -m_XT60 14AWG 0.1m pigtail terminals 16AWG, 1.2m, 170W Slim Tip +Nano 20W 1A
- female -m_XT60 14AWG 0.1m pigtail 18AWG, 1.1m, 90W DC7950 +ThP x201s 20W 1A
[1]: https://www.reddit.com/r/Lenovo/s/XwP4ZUjUYj
[2]: https://www.powerstream.com/Wire_Size.htm
[3]: https://www.thinkwiki.org/wiki/Power_Connector#Signal_Pin_2
[4]: https://www.aliexpress.com/item/1005013540077814.html
[5]: https://www.aliexpress.com/item/1005009384981530.html
[6]: https://shop470213879.world.taobao.com/category.htm
My alternative power sources:
modified R4875G1 server power supply (adjustable), 0~93V, 0~30A, 10 AWG, 1.0m cable, XT90/XT60 connectors
alternatively, it may be possible to use two smaller, identical "Slim Tip" power supplies connected in parallel
PS
It is possible to measure energy supply and/or consumption (separately).
RE: Check whether the terminals can accommodate a 14 AWG conductor (1.63 mm OD, 2.08 mm2 cross-section).
- XT60 pigtails with 14 AWG silicone-insulated wire (0.1 m length) offer greater flexibility when connecting to a PDB (Power Distribution Board).
RE: For soldered XT60 connectors, the maximum wire size is 12 AWG (2.05 mm conductor OD, 3.4 mm2 cross-section), rated for 35A (12 AWG / temperature rise <85°C); maximum voltage is 500V DC. Pay close attention to the quality of the solder joints (ensure the temperature remains <120°C under high current). The housing is made of flame-resistant polyamide (nylon) for safety. The connector is rated for 100–1000 mating cycles (if the male pins become loose, you can "break a toothpick inside" them to restore a tight fit). The connection should be held by the contacts themselves (the two 3.5 mm pins), not by the plastic housing.