r/AnalogCommunity • • 22h ago

Darkroom Built a darkroom in my basement.

Thumbnail
gallery
377 Upvotes

Hey everyone,

A while back I asked for advice on setting up a Durst M605 in a basement https://www.reddit.com/r/Darkroom/comments/1x294bj/setting_up_an_m605_darkroom_in_a_warm_basement/ . I’ve finally got it built and wanted to share the progress, plus ask for some "quality of life" suggestions!

Since I don't have plumbing down here, I set up a sink using a diaphragm pump pulling from a fresh water jug, and draining into a waste jug. I also mounted a dehumidifier on the wall (draining into its own spill jug), which is keeping the room nicely at 45-50% humidity.

Right now, I'm trying to figure out two main things:

  1. Shelving & Storage: The M605 is taller than I anticipated, and the existing wall drain pipes are sitting lower than expected, which makes mounting standard shelves above the bench a bit tricky. Any clever storage solutions for awkward vertical spaces?
  2. Water Temperature Control: Since my fresh water sits in a jug and the basement can drop in temperature, it's tricky to keep the water and chemistry at a consistent 20°C (68°F). What are your best tips for off-grid temperature control? Drop-in aquarium heaters? Seed heating mats?

Aside from that, what are your favorite "good to have" gadgets, workflow hacks, or minor upgrades that make printing easier? I'd love to hear them!

(Note: The photos make the safelights look a bit brighter than they actually are).


r/AnalogCommunity • • 11h ago

Gear Shots I just really wanted to show off this beauty 😌🫰🏼

Post image
81 Upvotes

Scored this one for a whooping 150$ and it came with a

- Tokina RMC Tele-Auto 135 mm f/2,8

- Tokina RMC 35-105 mm f/3,5-4,3

- Vivitar MC Macro Focusing Zoom 75-300 mm f/4,5-5,6

- 2x CFE Teleplus teleconverter

AND a Nissin Capital D400Ti lightmeter!

The catch was that the camera was sold untested, but after a quick check, it fired up! I'm yet to test it with film.


r/AnalogCommunity • • 21h ago

Troubleshooting - Photos What should I have done differently to stop the photos from turning out so grainy?

Thumbnail
gallery
71 Upvotes

I took these photos on the same day, within the same 30 minutes, in the same place and under the same weather conditions. Fomapan Iso 400. The photos were taken with a point and shoot (Carena AF super zoom 110so) on automatic mode but I switched the flash off. Apologies for the poor quality of the photo of the film negative… I’ve also attached some other photos from the roll. The film was developed and scanned by the lab.

/ thank you all so much, learning a lot :-)


r/AnalogCommunity • • 16h ago

Discussion It came today!

Thumbnail
gallery
67 Upvotes

It finally came after about a month. I guess that isn't too long a wait considering how hard it is to get it. Maybe I'll put one into my Fuji GA645zi fittingly enough.


r/AnalogCommunity • • 21h ago

Troubleshooting - Photos What is causing the glow around this person?

Post image
64 Upvotes

I’ve never seen this before. Shot on Portra 400. Any ideas?


r/AnalogCommunity • • 21h ago

Gear Shots Got one of my grails on my first Japan trip. The Plaubel Makina W67

Post image
46 Upvotes

I was hoping to find a 67 rangefinder with a wide angle lens during my time in Tokyo. When getting bummed out looking in Shinjuku by the selection and prices I kinda gave up on it. On my last day I went to GT Camera in Meguro City just for funsies. And there it was! Tested it and bought it.


r/AnalogCommunity • • 20h ago

Community Late grandpas Nikon F3 stolen (pity post) Melbourne AUS

Thumbnail
gallery
45 Upvotes

Today is a sad day, because my grandma came back to her house to find it trashed, with 35 grand worth at least stolen in clothes and accessories. She and I were most sad about the camera and lenses being stolen however, as they belonged to my late grandpa.

I've been improving my film photography ability with the OM2n as she said she would hand it down to me once I was capable. It was something of a dream camera, and certainly held emotional weight.

Along with it, a bunch of lenses were taken.

If anyone has information about how I could get it back, please let me know. Happy to contact through a signal/telegram message etc. I will be very happy to pay more than you can get for it these days (will drop off cash once I see it in person to maintain your anonymity).

Stolen in Glen Waverley, VIC

Also, I anticipate messages discussing scamming, I will be vigilant, and I know the camera. Despite being mint, it has a tiny mark hidden that I can identify it with.

Thanks everyone


r/AnalogCommunity • • 3h ago

Scanning Do Film Scanners Dream of Electric Sheep?

22 Upvotes

Using the GT-X830, I performed repeated scans of the same frame to measure the noise (σ_D) within the density space.

While the noise remains low—σ_D ≤ 0.01—up to a density (D) of 2, it degrades significantly to 0.287 in the D 3–4 range. Achieving an average noise level of σ_D = 0.02 for the D 3–4 range would require approximately 200 passes, totaling 40 hours.

I also consulted the manufacturer, who confirmed that there is no way to adjust the integration time or analog gain.

Consequently, I am building my own scanner that allows for manual control over exposure. The design repurposes the sensor from a commercial unit while replacing the control board with one of my own creation.

Further details are available on Qiita (link in the comments).

i wrote this in Japanese, and translate by google.


r/AnalogCommunity • • 2h ago

Gear Shots Lost my light, grabbed a beer

Post image
22 Upvotes

These early sunsets are a bit of a pain since I got back into shooting! On this day I was wandering the Santa Fe area of Denver, I like urban landscapes and especially alleys. You can always find something there worth documenting. Lost the last bit of light at the right spot…


r/AnalogCommunity • • 52m ago

Gear Shots Obsessed with my film journey...

Post image
• Upvotes

Decades ago (as my friend used to say, in the "dim times") as a young man and budding photographer, I dreamed of one day owning the top of the line Canon SLR, the F-1. Over fifty years later, I finally own one, and I can't take my eyes off her. She feels like she could stop a bullet or drive a nail. And now that she's been cleaned up and serviced, I can't wait to feel what she can do on the streets. She still needs a little TLC. Her meter is pretty far off. The battery (an alkaline 6V) seems to be strong, but I'll replace it with a lithium cell and maybe that'll help. Her shutter release is also a little laggy. Stay tuned. :-)


r/AnalogCommunity • • 22h ago

Troubleshooting - Gear Are scratch marks just a part of shooting film?

Post image
9 Upvotes

I've had this camera cleaned as well as cleaned the back plate with a dab of rubbing alcohol over a Q-tip before this shoot. Still, scratch marks across the film all over the frame.


r/AnalogCommunity • • 15h ago

Darkroom What happened to my Adonal?

Thumbnail
gallery
10 Upvotes

Hey, so I bought this Adox Kit in september and now it has exploded.

I only used this adonal bottle once and it was all tightly sealed... or so I thought.

I was away from home for a while and never even remembered to check the bottles since my CS-41 color devs are doing all fine in their bottles.

I had it in a corner of my room in the bag it came in, next to some film cannisters I turned into keychains. The bag was open btw and it isn't leaking when I press the bottle. Everything was covered in developer. Really weird.

Does anyone know how this may have happened?


r/AnalogCommunity • • 6h ago

Gear Shots Ricoh FF70 for $50

Thumbnail
gallery
8 Upvotes

Bought camera a day before a trip. Camera appeared to be faulty and skipped few frames, but I enjoyed this it a lot. Have used Portra 400, Color Plus and Fujicolor 200. Color Plus looking underexposed and doesn't suit cloudy weather even during the day. It came as a surprise as I used this film with og mju and results was great.


r/AnalogCommunity • • 4h ago

Discussion Which would you prefer Nikon F2 or FM2 or Pentax Spotmatic

7 Upvotes

The argument Ive searched thru google is both good, hard to focus without the waist view finder (F2) and FM is way cheaper than F2 but has 1/4000 if Im not wrong. I cant decide either of the two. Tho the spotmatic has M42 lenses and compact also fully mechanical

what would you get? considering all three are in good condition


r/AnalogCommunity • • 10h ago

Gear Shots Nikon SP

Thumbnail
gallery
7 Upvotes

I try to be modest day to day but I will make an exception for this camera. I have through lots of luck and genuinely kind people acquired this all in the span of about a month and all for pretty bargain prices. This all started because of the Nikkor - W 35mm F: 3.5 lens mounted on this camera. I realize its kinda like a tumor, it starts out small but then causes more financial investment and now has caused a camera to grow around the lens. Anyways I got really lucky and the guy sold it thinking it was just a extension tube or something. The SP here has a cloth shutter and is a pretty early example, the original prism had desilvering in the main finder but I got very lucky and met someone who had one on his spare parts body. The 35mm lens was not without issue though, that one had water get into it at some point and it had rusted the aperture blades somehow but I got very lucky and it was only light stuff. I took it all apart and the blades cleaned up with a little lighter fluid. The 50mm F1.4 came with the SP when I got it, its all there but the back element is a little scratched up and I have no idea where to get another one for this camera so I might just sell it off and find one in better shape. Who knows, thats the end of the camera info.

I have a roll of Cinestill 800t loaded only because I end up going out late at night more than daytime lately. I guess that is my test roll which is crazy to say. But I think the camera will work fine and I am very excited to make this my new workhorse. The case only came in the bottom half and it was pretty beat up. I wiped it down a bit then put leather conditioner on it. Should extend the life a little bit hopefully.


r/AnalogCommunity • • 19h ago

Community PSA: Don’t trust Japanese eBay listings to actually include import fees.

Post image
7 Upvotes

I bought a camera from Japan on eBay this summer, and even though it assured me multiple times that import fees were included and I wouldn’t pay anything after checkout, I still have FedEx hounding me to pay $38 in import duty.

Seller has ghosted me, eBay support was zero help.

Edit: I contacted eBay support again, and after almost an hour of back and forth, the told me that "import fees" and "tariffs" are not the same thing, so I am still on the hook for the Tariff. Seller is: samurai-camera0912 if you wish to avoid them.


r/AnalogCommunity • • 8h ago

Discussion Nikon FA or Canon A-1?

5 Upvotes

Which would you buy?


r/AnalogCommunity • • 41m ago

Discussion Recordak Junior Model JC

Thumbnail
gallery
• Upvotes

Can anyone give me any more info on this? I’m guessing this was some kind of microfilm reader or camera? Apologies for the poor pictures as this is in an office basement with poor lighting. Thanks in advance!


r/AnalogCommunity • • 22h ago

Troubleshooting - Photos Horizontal blurry line across all photos

Thumbnail
gallery
5 Upvotes

I recently found an old Pentax camera at my in-laws house. There's a persistent blurry line that appears at the same spot horizontally across all photos. Any thoughts on what the issue may be? The film was Fujifilm ISO 200.


r/AnalogCommunity • • 18h ago

Troubleshooting - Photos Vertical blurred line

Thumbnail
gallery
3 Upvotes

Hi y'all, does anyone have any idea why images appear to be blurry? Im using a Mamiya 645 and the issue has started to pop up recently. The photos were shot on different film backs as well.


r/AnalogCommunity • • 2h ago

Discussion Anyone here have experience post processing Super 8mm?

2 Upvotes

I'm working on digitizing my families old Super 8 film. I have most of them digitized and now I'm looking at what I can do to improve them a bit.

I have very little Premiere Pro experience but I'm already starting to play around with Warp Stabilization. In my first few attempts, I noticed that it does a lot of cropping, so I've started playing around with the settings to improve that.

I'm hoping to hear from some others to have been down this road.

Have you messed around with color correction? What are your preferred settings for stabilizing? Have you done anything to help clean up the image a bit more?

Has anyone dabbled in AI upscaling? I know the image is a bit shit so shit in = shit out so it may not be worth it.

I know the film is 50 years old at this point so I can only take it so far.

In case anyone is curious, here's a RAW sample straight from the digitizer and here's my first attempt at stabilizing. You can see how much it crops by default.


r/AnalogCommunity • • 22h ago

Gear Shots XT-3 mixed in summer still performing its duties

Thumbnail
gallery
3 Upvotes

Looks like tea.

Did a destructive strip test (as in, cutting a roll that I actually shot - honestly, my photos don’t matter that much) just to be sure. Haven’t used it in a month. Used 510 pyro and Rodinal recently.

Topping the canister up with a bit of Argon gas.

I use the replenishment method: The working X-T3 / XTOL bottle (depends on what’s in stock at the moment) is an accordion bottle and the air gets squeezed out before I close the bottle. I use a mix of accordion bottles and this 2.5l canister for the stock solution.

I mix it in just a 5l drinkable water plastic container very, very slowly, until the powder dissolves and mix in powder only bit by bit for part A and part B.

X-T3 mixes easier and has better environmental characteristics.


r/AnalogCommunity • • 7m ago

Discussion Expired film rules

Thumbnail
gallery
• Upvotes

I’ve been experimenting with expired film and I’m curious how everyone approaches it. I’ve heard the general rule of adding one stop of exposure for every decade past expiration, but I know storage conditions, film stock, and ISO can make a big difference.
Do you follow that rule, bracket your exposures, or just shoot at box speed and see what happens?
I’d love to hear what’s actually worked for you, especially with expired color negative film.


r/AnalogCommunity • • 10m ago

Repair Fungus on Olympus OM-1 mirror

Post image
• Upvotes

I want to get a second opinion of this mark on my Olympus OM-1’s mirror, which I believe to be a fungus. I’ve tried gently running over the area with a modern sensor cleaning swab to no effect, and currently I have it sitting in indirect sunlight. The mark is flush to the surface (does not stick out).

Is this fungus? And if so is there anything else I can try to clean/kill it?


r/AnalogCommunity • • 14m ago

DIY Om-1 shoe mount screw specs

• Upvotes

I was working on a DIY 3d printable cold shoe mount for the OM-1 because the Olympus shoe accessories are rather pricey to buy used and in short supply. I tried a couple different screws and then ultimately bit the bullet and got a used OEM shoe accessory. It seems to be 3mm and the thread is reversed but I can't tell the pitch. I searched the internet far and wide but sadly could not find anything concrete on the spec of the screw used. I didn't realize it was reverse thread before I got the OEM unit so I had just tried standard M3 and M3.5 screws to no avail.

Idk how many folks care about this but I already did a bunch of modeling and prototyping so figured I'd try and see things through. Any ideas? I was thinking ideally I need to find a screw of this spec available on a global online retailer like Amazon so folks can get the same hardware.

If nobody here knows Im also thinking of posting a high quality macro shot of the screw itself to a machinist subreddit and seeing if anybody there can eyeball it.