r/CommercialAV • • 2h ago

question Already using a 20x PTZ. What actually made your upgrade worth it?

2 Upvotes

Hello everyone! So I look after AV for a training room at our company. We use it for staff training and occasional talks, with some people joining remotely. There’s an older PTZOptics 20X-SDI Gen 2 on the presenter and a Sony ZV-E10 covering the wide. The PTZ feeds into OBS through SDI capture, and we stream at 1080p.

Before each session I check the presets for the lectern and demonstration table, test the mics, and load the slides. The setup is fairly repeatable. The presenters are less so. Someone usually ends up explaining something halfway between the two positions while I’m checking audio or bringing up their next slide.

The 20x reach already covers the room. What gets tiring is correcting the tighter shot throughout a session. We also save recordings for staff who couldn’t attend, so occasionally settling for an awkward frame follows me into the edit afterwards.

There’s budget to replace one camera, but the current one still works. Tracking and better recordings sound useful. I’m trying to work out whether either would make enough difference to justify replacing it, including getting everything set up and tested again.

Anyone upgraded a PTZ in a similar training room or lecture space? What actually made sessions easier to run, and what looked impressive in the demo but barely mattered once it was installed? Thank yall for any suggestion.


r/CommercialAV • • 3h ago

career Anybody coming to NAMM in January?

0 Upvotes

I'll be there with BoxCast showing off the RemoteMix product and some other cool new things we're announcing. Would love to connect with anyone!


r/CommercialAV • • 3h ago

design request Looking for a Reputable AV Company – Small Sound System Installation (Plains Township, PA)

4 Upvotes

We're looking for an established AV company or professional AV installer to design, recommend, quote, and install a small commercial sound system for our bagel shop in Plains Township, Pennsylvania.

We're envisioning a relatively simple setup:

- A small commercial amplifier

- 2–3 speakers strategically placed throughout the store

- Integration with our existing Mood Media player for streaming music

We're open to professional recommendations on the appropriate equipment and setup to ensure good, even sound coverage throughout the space.

We're specifically looking to work with someone who owns an established AV company or works for a reputable AV installation company, rather than an independent hobbyist.

If you're in the AV business or represent a company that handles commercial audio installations, please send me a message with:

- Your company name

- Your company website

- Your general service area

Ideally, we'd like someone who can assess the space, recommend the right equipment, provide a proposal/quote, and handle the installation.

Appreciate any recommendations or referrals. Thank you!


r/CommercialAV • • 7h ago

question Connector for SDI

1 Upvotes

Hello

I've an install With SDI Cable Belden 1505A.

I'll want to use the BNC connector Neutrik NBNC75BLP9  but I discovered that a special pair of pliers is needed, which costs $500.

Do you use other good BNC with a standard BNC pillers ?


r/CommercialAV • • 21h ago

career Seattle - Looking for a job!

8 Upvotes

Hi! I live in the Seattle area and am looking for a commercial AV job.. or even just a low voltage electrical job. I have about 3,000 hours as an 06 apprentice. I have experience pulling wire, installing network, security, audio, fire, shades, etc. I've done big commercial projects, high end residential homes, and most recently I was working for EOS doing conference room AV. I have had no luck finding a job so trying reddit. Would be happy to send resume if anyone is interested..

Thanks!


r/CommercialAV • • 1d ago

question Seeking Advice on Making Online Sales

0 Upvotes

Hey y'all! I am an AVL tech at a production/installation company that hasn't been offering online sales for many years. I was tasked by my boss to get that started up again on sites like eBay, Reverb, and GearSupply so that we could get niche gear out of our shop and into the hands of people that might be needing that specific piece of gear. I have not been at it for long, but I'm seeing how I might have a hard time gaining momentum. If anyone has any experience with doing something like this I would happily accept any advice. Thank you!


r/CommercialAV • • 2d ago

question The QSC CX-Q 4K4 status missing

1 Upvotes

The qsys perihperal manager status idel
Any help


r/CommercialAV • • 2d ago

question Tools and equipment tracking

5 Upvotes

Is anyone using tracking devices to monitor the locations of tools and test equipment? I’m misplacing ladders and power tools with the shuffling around of technicians that may leave some things on site until the job has been completed. Or a technician may forget where they left a kit. (That’s a topic for another discussion!) Would AirPods or similar be a good option?


r/CommercialAV • • 2d ago

question (4)8 ohm speakers wired for 8 ohms each channel

Post image
21 Upvotes

I’m wiring (4) 8 ohm speakers series and parallel for each of (2) channels.

First, is this right?

Next, how are 16/2 red/black wires run to each?

Seems like I need single wire runs.

A graphic with the wires in the jacket from each connection would be great.

ai can’t handle it and keeps making mistakes over and over. (chatGpt)

Appreciate any help!


r/CommercialAV • • 3d ago

design request DC Area Integrators

11 Upvotes

HI all, I am looking for some advice on A/V integrators (not AVI) in the DC area. We need to upgrade/replace an audio board and wireless mic setup. Budget is not a huge factor.


r/CommercialAV • • 4d ago

question Needing some guidance on TV wall

2 Upvotes

Please give me your feedback and thoughts on this.

We are thinking about making a TV wall with 4 100" TV's. This will be a presentation wall. The screen will be about 30' to 40' away from the main seats.

Should we do this and if so what is the best way and any alternatives.

Thanks.


r/CommercialAV • • 5d ago

troubleshooting Vonyx WAT200 – Multiple receivers on one transmitter not working. Any ideas?

1 Upvotes

Hi everyone, I'd like to ask for some advice regarding a wireless audio system.

I'm looking for an affordable assisted listening solution for hearing-impaired people at our church. The idea is simple: one transmitter connected to our mixing console, with multiple receivers so people can listen using their own headphones.

I purchased a Vonyx WAT200 UHF system and an additional WAT200R receiver.

The original receiver works perfectly, but the additional one won't receive any audio, even though both receivers and the transmitter are set to the same frequency (863.4 MHz).

I contacted the retailer (PROFI DJ), and they told me that using multiple receivers with one transmitter is not standard and that this system doesn't support it. They even said they weren't aware of any system capable of doing this.

However, the manufacturer's manual specifically describes how to pair additional receivers, so I'm a bit confused.

I've tried different pairing procedures, checked the manual, and even spent some time troubleshooting with AI, but nothing has worked so far.

Am I missing something obvious? Is there a specific pairing procedure I should try?

Otherwise, I really like the system. It's affordable and works well for our needs. I can still return it, but I'd much rather get it working.

Any advice or recommendations for alternative systems would be appreciated. Thanks!


r/CommercialAV • • 5d ago

question My mistake on a remodel: Mounted a projector lift without checking above the ceiling, hit an HVAC duct. How do you handle this?

Thumbnail
gallery
0 Upvotes

Wanted to share an honest mistake from a commercial remodel I worked on recently.

We were installing the AV setup (projector lift, motorized screen, rack, and wall speakers). The original plan was to have the projector fully recessed inside the ceiling.

My mistake was that I proceeded with mounting the projector lift without properly checking what was hidden above the acoustic ceiling tiles first. Combined with an oversight in the renovation design, we ran straight into an existing HVAC duct.

The ceiling plenum was simply too shallow with the duct right above it, so there was no way to retract the lift flush into the ceiling. As you can see in the photos, the lift ended up hanging down below the ceiling line.

Obviously, if I had caught this before mounting, we would have done something else. But since it was already hung, I talked directly with the client.

Luckily, the client had other interior finishing work scheduled for the room anyway. They agreed to just build a neat trim/casing around the protruding lift along with the rest of their carpentry work.

The installation itself came out sturdy, level, and the projection alignment is spot on. Thanks to the client's flexibility and existing finish schedule, the whole thing wrapped up nicely without any major drama.

It all worked out in the end, but it got me thinking:

  1. In your country/market, how do you guys handle unexpected HVAC obstructions during a remodel?
  2. Does the job usually get compromised on-site like ours, or have you seen contracts get completely cancelled over plenum clashes?
  3. When old as-built drawings fail to show mechanicals, who usually takes the blame?

Curious to hear how other installers handle surprises above the drop ceiling!


r/CommercialAV • • 5d ago

question Poly X72 question

1 Upvotes

Hi guys, quick question since I can't seem to find a concrete answer for this, is the Poly X72 compatible with the Poly IP microphone ceiling arrays? (875S1AA)

I'm finding conflicting information / no information at all, I've got the kit here but it doesn't seem to want to detect the mics


r/CommercialAV • • 5d ago

question HDMI Matrix

2 Upvotes

What brands are you guys using for an hdmi matrix? I just need something simple.


r/CommercialAV • • 5d ago

question Front-end for easy changing of VLANs and PoE port bouncing

3 Upvotes

Has anyone used or is aware of a platform that would let AV staff directly configure vlans and bounce PoE ports, without having to go through IT staff? Curious on the front-end and back-end systems in place (such as a front-end interface that interfaces with back-end Cisco, Arista, Netgear AV, etc).

I know some enterprises have integration with help desk systems like ServiceNow, which is one option but I'm hoping for something simplier, something like a webpage or app one can pull up on a phone a quickly make a change. But I'm interested in all solutions, small, medium, or large.


r/CommercialAV • • 6d ago

troubleshooting Logitech conference room equipment issue

0 Upvotes

Why are several of our office conference rooms having such frequent disconnect/reconnect events? The mic pods are the main culprit, but the Rally Bar is also doing it in a few cases. Sometimes they come back, but I'm frequently having to reset the equipment in these rooms. It's driving me crazy.


r/CommercialAV • • 6d ago

question I just Passed the CTS last week! already scheduled CTS-I, any tips advice? Concerns?

20 Upvotes

I’ve been in the AV Commercial integration 10 years this upcoming new year, I’m in the Hybrid role of a Lead Technician and commissioner. I believe my current role and in-field experience will help a ton but I’m still using Avixas Online CTS-I courses and the physical exam guide. Any suggestions would be greatly appreciated!! Thanks guys!


r/CommercialAV • • 6d ago

question Qsys touch panel installed in gym. Protection options?

Post image
29 Upvotes

Recently installed Qsys touch panel in a gym. I am worried about it getting hit by a basketball or a volleyball. Any options out there?

It doesn’t need to lock as it will be PIN protected.

I was thinking a clear thermostat box? Something that flips up or down would be nice though.

Picture for reference


r/CommercialAV • • 7d ago

question BrightSign HD224 drops frames on a 4K lobby loop, vidione export at 60fps, should I go down to 30?

1 Upvotes

Office lobby, one 55 inch commercial display, BrightSign HD224 playing a 90 second loop from the SD card. The loop is mostly slow pans across product photos with some text on top.

I cut it in vidione and exported H.264 at 3840x2160, 60fps, about 40 Mbps. Every few seconds there's a visible hitch on the pans. A 1080p test file plays smooth.

Is the HD224 just not meant for 4K60 at that bitrate, or would H.265 at 30fps fix it? I'd rather not swap the player if an export change does it.


r/CommercialAV • • 7d ago

question How much should I get paid with 3 years of commercial residential installation and basic configuration, 1.5 Years of Onsite AV Tech, and 1.5 years of programming and commisioning I am doing in ottawa. Govement sites. CTS, Crestron Certifications

4 Upvotes

I have Crestron certification, biamp, extron, qsys level 2 and all UCI and control certs. I also have CTS. I have completed 3-4 projects independetly in govements sites, I am secrete clearance level 2. I do so many service calls and get the result as well. I am preparing for CCP(Crestron Certified programmer) and doing installation as well whenever team needs help. I struggle with audio and still need senior to help me with it though.
I was wondering if i am getting paid fair as I am getting 70K right now. How much minimum I should be getting and how much Raise I should deseve??

appriciate your suggestions.


r/CommercialAV • • 7d ago

meme/off-topic Worst soldering?

Post image
13 Upvotes

I saw a terrible RJ45 post and thought I'd share this delight I came across some years back.

Wrong pins, and it looks like they used a fire poker.

Internal install guys at a large European firm.


r/CommercialAV • • 7d ago

meme/off-topic Tech- I finished terminating all the drops behind the displays

Post image
41 Upvotes

This ‘termination’ was the worst of the 10 of 12 that had to be reterminated.


r/CommercialAV • • 7d ago

question Opinions on AV system for dance studio

Thumbnail
gallery
0 Upvotes

Hi all I posted on here a couple months ago about opening a dance studio and am now working toward the system ill be using. Here is my current pricing sheet with all the items included (i also got a quote from pro audio). I want to know a couple of things. How is my revised sheet compared to the actual projected amount? Is there anything wrong/won't work for my space? Am I missing anything? Are the speakers to small for the space? Etc. Any help would be greatly appreciated. Here's a link to my original post: https://www.reddit.com/r/CommercialAV/s/3k2pp3B4v6

Edit 1: added sub woofer: JBL Control SB2210 Dual 10" $700 Mixer replacement: Mackie ProFX10v3+~$330