r/Creality • u/OldManGrimm • 2h ago
Mods & Upgrades Printed a lid hinge for my K1C, added some wood accents
galleryThe laser cutter is a Falcon Pro 10W, so also from Creality.
r/Creality • u/OldManGrimm • 2h ago
The laser cutter is a Falcon Pro 10W, so also from Creality.
r/Creality • u/Emil24_KhaKukmor • 59m ago
r/Creality • u/fifindr • 20h ago
Designed this table extender to add a bit of extra workspace without needing a bigger desk.
It slides onto the edge of a table and uses a screw clamp underneath to hold everything in place. No drilling or permanent modifications needed, and it gives you an extra surface for keeping things within reach.
Creality Cloud -Table Extender From fifindr https://www.crealitycloud.com/model-detail/table-extender
Hope you like it!
r/Creality • u/ZeroDayBurn • 12h ago
Finally finished my 40-inch 3D-printed Christmas wall art.
Designed and printed in PETG on my Ender 3 V3 KE, with RGBIC backlighting and a gloss white finish. I wanted to see how far I could push 3D printing as a medium for decorative wall art.
Pretty happy with how it turned out, and I've already got a few ideas for future designs.
Curious to hear what you guys think!
r/Creality • u/ShiroDiesAlot • 3h ago
Help a bro out 😁
r/Creality • u/psychoanalyst_god • 7h ago
r/Creality • u/Snafu4d • 14h ago
I want to start by saying I'm not new to 3d printers. I have been 3d printing since 2013, and no printer has been as maddening as this one. I decided to get this printer as it seemed like a nice upgrade. I've had it set up for 90 minutes and have yet to get it to print anything. Every print I start it seems to get into a doom loop of homing, purging, wiping, homing , purging, wiping, and on and on.
How freaking long do I wait for it to actually start a print!?
I updated the firmware first thing. I ran the self leveling. It acts the same with preloaded files as well as ones I sliced myself. And whether calibration is checked or not.
Is this normal? Will it get better after it actually finishes it's first print? I'm used to the old days where all this stuff was not automated, hitting print, waiting for it to heat up, and away we go.
r/Creality • u/Low_Ambassador5747 • 8h ago
Ok I mistakenly just bought a Ender five s1 with missing pieces I had a rough day and I made a spontaneous purchase of this 3-D printer. Been looking at one for a while, but for some reason, I picked this one. Well little did I not realize when I picked it up and handed over the money that it was missing the full assembly for printing. No extruder no hotend no extruder backplate not x axis pulley band. Unfortunately, I’m stuck with it now I’m a mechanical engineering student so I can try to figure it out, but I’m not seeing any upper replacements at all for the components missing. Does anybody have a clue on how to help me?
r/Creality • u/InflationCurrent4288 • 8h ago
r/Creality • u/M4gn00nguN • 16h ago
I’ve tested the cable and it is working with other CR Touches I’ve also updated the firmware but it didn’t change anything… is it fixable? I think is the CR Touch’s conector or the chip… But don’t have a clue on how to fix it. Please HELP.
r/Creality • u/minorhassle • 12h ago
I've been without my K2 for over a month now. My experience may serve as a cautionary tale, especially for those researching a future printer.
I like Creality products- they are good value in the hobbyist market. And I'm pretty knowledgeable around tech and computer-controlled equipment and have a well-equipped shop. But every printer needs some maintenance at some point. Creality products in general seem to experience incessant engineering revisions that make sourcing parts difficult. My latest problem is ordering parts from the Creality store specified to work with my machine, only to spend inordinate time reconciling instructions for an earlier revision with what I was sent. Which is OK unless you are sent the wrong part. That wouldn't fit nor would it, being the wrong part.
I am corresponding with Creality Customer Support, of course. But know that they are based in China (nothing wrong with that) and it takes 24-48 hours for me to have my email reacted to. And their responses are polite and helpful.
But if you are expecting something bullet-proof that you can maintain, expect delays in the repair process even given any technical prowess and equipment you might have. That's just a reality of an international market. I shouldn't have made production promises I can't keep. So that's on me.
r/Creality • u/nighthawk2174 • 17h ago
I have a ender 3 max and have been having major issues with it. I had printed just fine for a few weeks, several hundred prints when while setting the bed mesh before a print which I’d just run successfully the hotend dragged on the bed badly. Just before this it’d damaged the plate by dragging while establishing the bed mesh (first image). I followed the recommendations of support and everything seemed fine and it ran fine for a little longer. Then on an overnight print the tool head stated dragging majorly bad about halfway through the second layer on a massive print (second image). It pushed through the print and cut almost through the spring steel bed. The hot end nozzle was ripped out and I got a 2510 error. From what I could find the only fix was to replace the main board. Which I did along with the hotend which was damaged. Now two weeks later and maybe 30-40 prints I have the same error. It started with a 2560 error. And after rebooting the printer I got the 2510 error with the bed temp showing -67C. Also when looking at the bed it dragged on the bed plate again while establishing the bed mesh.
This is now the second main board to go out. What causes this? Is this main board design just defective or is it just me? If it is is there a good aftermarket solution.
r/Creality • u/aphla52 • 18h ago
I took out the screws to install a new bed and fix things now i got 4 that don't wanna go in. Help please
r/Creality • u/Legitimate_Buddy_974 • 1d ago
The first one I printed printed BEAUTIFUL. Then I tried to print 3 more and the supports failed on the first one at this spot. Cleaned the bed with iso and started again and failed again. Cleaned the bed AGAIN and started this one and came down this morning to the SAME thing. I was not losing this one too 🤣🤣🤣.
r/Creality • u/kertj1 • 20h ago
I was given a used CR-10 Smart Pro printer. I couldn't get it to connect to the iPhone app on my network. I opened the unit and found the network board. This board contains an SD card. I mounted it in my PC and found that the card was completely full. I removed the visible log files but this only freed up less than a gigabyte of space. I found a hidden directory named FOUND.000 that contained tons of additional log files. I removed all those files and now the disk is almost empty. I reinstalled the disk into the internal board. Reapplied power and it connected to the phone app just fine. Posting this in-case this helps someone in the future.
r/Creality • u/Igotdaruns • 17h ago
My bed is warped and I have been using printer paper strips stacked to get it within tolerance. I was wondering if anyone has ever just printed a shim across the bed using the bed mesh data? Seems as though you could interpret the data and then model a shim that you could print directly on the bed then use a second removable flex bed as the new bed. You could even peel the sheet and just place it underneath.
r/Creality • u/Grouchy-Estimate-671 • 1d ago
Just this week, my co-worker gave me his old 3d printer because he got a new one. I went out and bought all the stuff I need for it, really exited, got all the proper.gcode files, and when I went to actually get started printing, it keeps stopping. The nozzle moves along the x axis, printing a single line, then the nozzle lifts and returns to the starting point, then all the temperatures that took forever to heat up (the preheat on the filiment and the temperature of the bed) start dropping to zero as it all stops. I'm really frustrated and worried it's all gonna be a bust after I spent so much time working on trying to troubleshoot this thing. I believe the printer is a CR-10s. Can anyone please please please help me? I am 100% sure that all the file information is correct, I have the correct type of microSD, I have the proper filiment (it's hobby lobby brand), and the guy who gave it to me, while he did tell me there was some stability issues (looks like he Jerry rigged some system with poles to keep it steady), he never said there were any problems like this and I won't see him at work for a few more days, so I can't ask him for help. He showed me some prints hedid and they all looked great, so I'm not sure what's going on. Chances are I'm doing something wrong, but I don't know. Some help would really mean a lot to me. Thank you.
r/Creality • u/Content-Rabbit-9865 • 22h ago
Printed the following items. This is the total from the ‘Poop Shoot’. Should I change a setting on my K2 Pro CFS?
r/Creality • u/Careful-Oil769 • 19h ago
This is a part I've printed dozens of times, just re-sliced for different materials. I haven't quite figured out if it's the slicer, since there are scaling and saving "glitches" I've found (version 7.2, I think).
Three times in a row now—same part, tried a new slice—I've ended up air printing on my K2+ after a few hours. I want to blame the roll since I'm also seeing red dust shrapnel on the silver extruder wheel when it happens, so it's definitely shredding a bit, possibly due to oversized filament on this roll (Kingroon PETG bulk pack red).
However, this particular unit has 5,500 hours or so on it. The only things I've changed are nozzles, a couple of extruder covers, and lots of PTFE tubing. I also had the CFS filament detect light come and stay on for slots 3 and 4 on one unit that I couldn't clear by disassembling, air blasting, and re-assembling. Now slot 2 on my second CFS is doing the same. I said screw it on the first one and replaced the two faulty modules since they're only $25 a pop.
Replaced the nozzle, still clogged after about an hour.
Last night replaced the throat cooling fan and hot end, than a full calibration and a PID nozzle tune at 250(PETG).
I'm using BN thermokote paste on the heat break versus the included Creality stuff, been using this product for years without an issue.
Ran about 30 minutes than clogged again.
I did switch to a different roll of filament as well as replacing the tubing between the buffer and hot end. Still no luck with correcting the problem.
Tonight I'll try bypassing the CFS and running off the side spool to see if it has any effect on what's going on.
I'll also replace the whole extruder gear assembly, could be that there's something worn internally causing additional resistance.
I've never come across a problem like this that wasn't fixed by the steps I've taken so far so it's been an interesting journey so far.
r/Creality • u/Creality_3D • 1d ago
Hall 12 Level 1, B49 📍
16:15 - 16:30 (GMT+1), Thursday 19. Nov '26
FORMNEXT 2026 product launch has been rescheduled.
Be the first to see what’s next. See you there! 🚀
r/Creality • u/lisyGracz • 22h ago
Has anyone encountered this? Neither via QR code, nor via email, nor through Google.
r/Creality • u/Repulsive_Type406 • 23h ago
I am currently trying to print in PA12-CF, but it keeps messing up. I use Creality Slicer and Orca Slicer; does anyone have a profile that works well for the K2 Pro, please?