r/Machinists • • 3h ago

NSFW GORE: click at your own risk Another reason to be serious about safety:

Thumbnail
gallery
717 Upvotes

I was 22 and an "apprentice"* *at a fabrication shop, IE: I polished things.

Working on a large lathe with a 20 foot bar of 3/8" stainless, on several dead men rollers. Large die grinder with a drum sander, polishing the rod because the owner "couldn't afford" polished rod.

Also wearing the freshly made dickies work shirt, sleeves down, as instructed per management for uniforms.

Lathe was on 33~rpm. Low grit sand paper. I'm 10~' from the controls.

Drum bounces off the rod, arm hits the rod, rod grabs sleeve. It bundled at my wrist and simply ripped the shirt each rotation to my elbow. Then it started to hurt, each rotation was causing the shirt to twist and grab parts of my arm. Each mark you see was a rotation of the rod.

It was slow enough that I realized the world of trouble I was in, I think the math was something like 8-11 seconds? The rod had pulled me in and it was in my armpit, I was about to either lose my arm or start rotating with the rod. I didn't realize I'd been screaming help, and the Bridgeport operator saved my life. I'd always wondered what it would take to make me piss myself, and I learned that day.

I was warned by the owner that if I went to the Dr that there could be consequences, and being a "good employee" I never went. I tried calling out the next day, and was told to come in or I'd be fired. I spent a few weeks polishing weld color off with my good hand. At one point my entire peck and neck were black and blue. Luckily no lasting effects. The scar photo was 3~ years after. Now 15~ years later they're hardly visible. I still have the shirt, and it has the chunks of skin still in the bundle.

So in short, be careful. The machines will hurt you and keep going. They don't care. Also cherish yourself more than a shitty boss. Fuck you Adam.


r/Machinists • • 16h ago

Just a reminder!

Post image
333 Upvotes

r/Machinists • • 4h ago

Updates on this part with new strategy

Thumbnail
gallery
85 Upvotes

2 days ago I posted this part with a terrible surface finish that came after 9 operations on CNC mill. Lot of people commented and I corrected my strategy and tools based on them. This is the result. It has waaaaay better surface finish, lower cycle times and only 6 operations.

My new strategy was this:

  1. Rough machining 2 ears (adaptive) + finishing 2 ears (zlevel) + counterbore (zlevel) with 12mm carbide tool

  2. Drill the counterbore hole (10.5 mm)

Turn 90 deg.

  1. Rough the bearing seat (adaptive) + finishing (zlevel) with 12mm carbide tool

  2. Contour miiling the Retaining ring groove

  3. Chamfer with a countersink

Turn 180 deg.

  1. Chamfer with a countersink

There is a little chatter on the walls (although it feels totally smooth) which I think is the result of my tool not being rigid enough. For the future parts I will purchase a 18 or 20 mm carbide tool to reduce vibrations. I will also use a bigger and shorter holder.

Thanks everyone for the previous comments! You helped a lot!


r/Machinists • • 21h ago

PARTS / SHOWOFF The way the sparks shoot straight out the end on these tiny tube laser holes

84 Upvotes

Was a little nervous before hitting cycle start on this run. Cutting a dense pattern of tiny square holes along the tube puts a ton of heat into the part, and I was worried it was gonna warp or leave a nasty buildup of dross on the inside wall.

Felt a lot better seeing the gas blow all the sparks and slag straight out the open end.


r/Machinists • • 2h ago

A toy car I machined at college

Thumbnail
gallery
77 Upvotes

I am a Mech Engineering student and we have a machining elective which I took, I used both a lathe and a milling machine, all 0.1mm tolerances met, it was done in a span of eight weeks, each image was a different week, and all work was done in a safe environment

I only tried the safety breaker once and disassembled one cutting bit as I was too eager on the chunking

Material, apart from the M4x20 screws is 6061 aluminium.

The "cockpit" was done on the milling machine and the "driver" is a ball bearing hammered into the cockpit

Picture 5 was taken behind protective ballistic glass, hence the haziness

Pic 7 is my finished product!

Ps.: sorry for the extremely evident machining markings, the lathe lacked needed lubrication


r/Machinists • • 22h ago

QUESTION How to identify an insert? Please don’t be mean, I’m not a machinist… just order the parts…

Thumbnail
gallery
44 Upvotes

Just want to preface this by saying that I am not a machinist but I run a shop with a machine shop in it. How do I identify this insert to order more?


r/Machinists • • 5h ago

The orientator

Post image
44 Upvotes

Needed to drill a hole parallel with this existing hole, now this exists. Worked for the 100 parts I needed.


r/Machinists • • 22h ago

Gauge for 20T press

Thumbnail
gallery
12 Upvotes

Can I put a gauge on either of these ports to measure pressure at the cylinder?


r/Machinists • • 12h ago

QUESTION What's the best website for uploading and archiving manuals for old cnc machines for free?

7 Upvotes

I have a couple of old manuals and Error and Alarm lists for Okuma CNC machine that I want to scan and archive for other users for free use, and I'm looking for recommendation which website to upload them in without any kind of lock or paywall.


r/Machinists • • 10h ago

F360 tool path help

Post image
6 Upvotes

What tool path would be good for this? I was thinking a 2d contour with a 2” face-mill but I’m having problems configuring it to lead in and lead out right as well as getting it to face only the face on the diameter

I want to face the part but not in the typical zig zag fashion I want it to spiral around the diameter


r/Machinists • • 6h ago

QUESTION Heeelllppp

Thumbnail
gallery
1 Upvotes

Can anyone see a reason why I'm getting this alarm? There are no other P Q lines with the same numbers. I'm at a loss.


r/Machinists • • 4h ago

Shitpost New fears unlocked monthly.

2 Upvotes

Started a job that’s a pretty old shop and I’m usually mainly CNC or smaller manual machines. I did work as an engine machinist for awhile that was mainly all manual besides the guides and cutting the valve seats. 95% of my jobs is running machines sometimes older than me and feeling real cool and component, the other 5% imaginary near death experiences or nearly doing something completely stupid that would critically injure me 😂 they just keep throwing me on weird set ups and brain fog has me disoriented at some point in the day. Today it was a hydraulic clamp I almost activated while my thumb was lining up the part. Last month it was manual lathes and how easily they could kill you. But I usually remedy by testing and put a .005 feeler under the hydraulic clamp and tried to pull it out and realized that would have certainly broken my thumb or nail even though it looks unassuming and not dangerous the way it is in the set up on the saw.


r/Machinists • • 18h ago

Thoughts on EDM

2 Upvotes

I'm looking into getting a newer used EDM machine for a training lab I'm building out. Any suggestions about brands or things to look out for on used EDM machines. This will be my first time using an EDM machine.


r/Machinists • • 23h ago

Cutting Tool Selection and Recommendations for A286 Machining

2 Upvotes

I am machining Ø18 mm A286 material with a hardness of 25–30 HRC on my Haas ST-20Y CNC lathe. I am not particularly satisfied with the tool life and performance of my current cutting tools.

I am currently using TaeguTec VBMT 110308 inserts for rough turning and VBMT 110304 inserts for finishing.
For drilling operations, I use WIDIN solid carbide drills in Ø10 mm and Ø8.5 mm.

Could you recommend higher-performance cutting inserts and solid carbide drills that would provide better tool life and machining results for this application?


r/Machinists • • 1h ago

QUESTION Feed rate won’t go to 100%?

• Upvotes

I’m an operator running a Doosan Puma 3100 and for some reason the machine refuses to go to 100% rapid. No error codes, no alarms no nothing. Just stuck at 25%. Asked the head machinist and he said he’d never seen it before then walked away. Any ideas? Tried basic stuff like power cycling but I’m not the most knowledgeable about machine repair.

Also I have seen it turn itself up to 100% a few times but not for long and not for any reason I can discern and it always goes back to 25%. Been this way for a few weeks now.


r/Machinists • • 3h ago

Looking for a shop with multiple spindles available now. Need 31" in X. Aluminum parts. 2 setups. Need qty 30 pcs. Initial testing I had 6 hours of 3d contouring per part (w/ a 12k spindle & 1/16 ball). 30x6 hrs = 180 hours. I don't have that much time. Willing to pay decent money.

1 Upvotes

Shoot me a DM. +/-.005 except for 2 locating pins.

Designed by a machinist. Can't post a pic but can email model for approximate quoting and lead time.

Thanks.


r/Machinists • • 4h ago

12 mm x 1.0 thread ring gauge go/no go

1 Upvotes

Need one of this for a project . Anyone in OKC have one or a used one to sell ?


r/Machinists • • 16h ago

QUESTION Machinist/Welder Preparing for Job Hunt

Post image
1 Upvotes

Hello everyone, I'm 29 years old and located in the KC area. As the title states, I've got two machining associates degrees and just finished my last class to earn my welding associates as well.

I had a machining job around seven years ago but got out of the trade to focus on some other things in life, but kept taking machining and welding classes in the meantime. I'm looking to get back into machining or welding, or some kind of hybrid position.

Would anyone have any advice for me on what types of positions to look for? Has anyone else in this sub found success finding something that combines the two trades? Or just what kind of advice might you have for someone job searching in either of these trades right now? I look forward to advice anyone may have!


r/Machinists • • 12h ago

QUESTION Aren't you paranoid to let the tool run again on just 0.02mm?

0 Upvotes

When you are doing a setup and measure the piece and its off by 0,000787 inch

Or 0.02mm, it seems better to adjust and let the next part be good,

Especially on 304 and Titanium, but I had colleague who would let tool run across path that was already milled, which should be degrading the tool faster due to rubbing or am I trippin? And how much abuse can a tool take?


r/Machinists • • 7h ago

QUESTION If you had to make a test to see a persons setup capability, how would it go?

0 Upvotes

Thats exactly what am going into on monday and wondering how to prepare, so get the job after operator role