r/buildingscience • • Jan 19 '21

Reminder Of What This Sub Is All About

94 Upvotes

Hey everyone,

There's been a bit of spam in the mod queue lately and I figured it'd be useful to touch base and remind folks what this space is really all about.

It's not a job board or a place to promote building products (unless you're talking about some brand new membrane dehumidification product that nobody's ever seen before). It's not a place to have people help you figure out how to unlock a door. It is a place to discuss questions about how products work or fail, field techniques, research literature, adjacent relevant fields of research, and field practices. Remember that this is a unique science subreddit in that we occupy the space between research, manufacturing, and field reality. We are one of the best examples of applied science out there. So let's think about content through that lens. Let's share things that advance the conversation and help people take their learning to a deeper level. All are welcome, just don't spam pls.


r/buildingscience • • Jan 26 '23

Building Science Discord

Thumbnail
discord.gg
9 Upvotes

r/buildingscience • • 5h ago

Smart vapor barrier for 1890s renovation

4 Upvotes

I’m trying to decide which smart vapor barrier is better for my 1890s farmhouse renovation. Foundation/ new floor system has been repaired and replaced. I’m getting closer to insulating (northern Michigan winter coming soon). Going back and forth between ProClima Intello plus vs Certainteed Membrain. Exterior of the house is original lap siding over the studs which is covered by vinyl siding ( I’m hoping when the vinyl was added there is a house wrap but I won’t be certain until I replace the windows. I’ll add the house wrap everywhere I am able if it isn’t there when the vinyl comes down for the windows.

I am leaning towards the Intello plus based on my research, only part that I am nervous about is sealing up the wall cavity too good as the house was never originally like this and there has been absolutely no rot. Current plan is to insulate with rockwool, then add smart barrier over the studs, then 1/2 inch osb to prevent further racking etc. drywall after.

Any thoughts? I haven’t reached out to either manufacturer to check thier opinions on osb going over the top and how that changes vapor permeance


r/buildingscience • • 5h ago

Question Open cell spray foam for Michigan rim joist - does this need remediation?

2 Upvotes

I had open cell spray foam sprayed into my rim joist in a 1995 era Michigan home with an unfinished basement about four years ago. When I've dug through the foam to run wires the wood behind it seems fine. But I understand that open cell in a rim joist can promote moisture issues. Do I need to remediate this, or is it probably ok to leave as is?


r/buildingscience • • 2h ago

Best way to insulate crawlspace?

Thumbnail gallery
1 Upvotes

r/buildingscience • • 13h ago

Red Steel Building Insulation

Thumbnail reddit.com
1 Upvotes

r/buildingscience • • 18h ago

Question Roof vents vs soffit - cold weather climate

2 Upvotes

Hi everyone

We live in a small, old house in Calgary Alberta and need to up our insulation. Soffits are not vented and would require a lot of work / $ to get them to a point that would support the extra attic insulation we also require. Roofing fella suggested we opt for several roof (intake) vents instead. It seems a popular option for new builds, but I’m also wondering what the chances of them getting blocked by snow in the winter months.

Any experience you can share? Thanks.


r/buildingscience • • 16h ago

Climate Zone 5a without furring

1 Upvotes

Hello all,

I am building a home in climate zone 5a. From my research, the requirement on my plans (r-20 + 5ci) is not a great idea because of my cavity to continuous insulation ratio. I am going to use r-21 batts but am unsure of what to use on the exterior. It seems like I should be using something R-7 or higher but this would be a minimum 1.5" thick and require me to install furring strips in order to install LP Smartsiding (installs over 1" foam maximum). Can someone help me determine other options with 2x6 framing, r-21 insulation, and no furring strips? Would these options be acceptable?

Option 1: Use Zip-R9 and LP smartside attached with tetragrip nails

Option 2: Use R-21 insulation and r-5 ci but with a smart vapor retarder between drywall and studs


r/buildingscience • • 7h ago

What does breathable actually mean in the context of a building?

0 Upvotes

What does breathable actually mean in the context of a building? Does the building breathe like I do with air coming into my lungs & back out again as carbon dioxide? 
 
No, not exactly.  
 
It means that the building materials can transmit moisture. 
 
Breathable building materials are permeable enough so that any moisture from humid air & moisture from surface wetting can be absorbed & can then easily evaporate during dryer warm periods. 
 
A lot of natural, traditional building materials have inherent properties that allow moisture vapour to pass through them, they are vapour permeable. These materials can also absorb & retain moisture in vapour form [like moist damp air in the background or from a bathroom], this means they are also moisture buffering [the scientific word for this is ‘hygroscopic’]. 
 
Another way to describe these 'breathable' building materials is that they are ‘vapour open’ or ‘vapour permeable’. 
 
This is very different from some modern, synthetic building materials that are made from fossil fuels & plastic and are heavily processed. These are the opposite & therefore classified ‘vapour closed’ or ‘non-vapour permeable’. They don’t ‘breathe’. 
 
Here’s a couple of cross section sketches that show how this works in practice. 
 
Sketch 1 illustrates a breathable vapour OPEN construction. 
 
Breathable vapour open buildings mean that background water vapour is intended to enter the constructional build up, it’s not intended to stop it entering. Over the colder, damper winter months, with higher internal humidity, a certain amount of water vapour moisture can enter the build-up & is temporarily stored in the insulation. Then, over the warmer, summer months, when the internal humidity drops, the stored water vapour moisture can evaporate harmlessly into the room. 
 

Breathable vapour OPEN construction

Sketch 2 illustrates a non-breathable vapour CLOSED construction. 
 
Sealed vapour closed buildings can work but as they rely on internal vapour control membranes that are not vapour permeable, they need extremely good site workmanship [should that be ‘workpersonship’?] to ensure the insulation is fitted tightly without edge gaps and the internal membranes are installed fully sealed without any gaps or holes. In reality it’s likely there will be gaps, as I understand it is impossible to ever build a 100% fully sealed construction. 
 
Nature knows best, who’d have thought it?

Non breathable vapour CLOSED construction

r/buildingscience • • 18h ago

Dense glass fire rated wall

Thumbnail reddit.com
1 Upvotes

r/buildingscience • • 23h ago

Do any of you building science enthusiasts garden, and have a need to overwinter a few plants?

2 Upvotes

I’ve run out of time on the central coast of NJ, and I need to get my two small citrus trees into their winter home.

Not only have I lost the battle against fungus gnats in the soil the past few years, but I never really had a place inside to keep these potted plants to begin with. No basement, no sunroom, so extra space at home anywhere :(

Unfortunately, the lemon and lime pair were purchased without considering where the plants would live during the winter. Even though I was not happy to see them arrive after they were purchased, I do like them and want to keep them alive.

I need some kind of temporary solution to overwinter these plants for 1-3 cold seasons. I have access to more than enough extra,and scrap, zip sheathing, rockwool batt insulation, and everything else to build a nice little box. All the fasteners, sealant, and tape you can dream of. I can purchase anything else needed, but I wont need much. I even have a bonus bucket of Redgard, extra fiber cement and aluminum siding, and exterior paint if I want it to look nice.

What I was thinking was a mini “shed/greenhouse”. Its joists will rest on those plastic feet people build sheds on. Insulated floor(?), insulated walls. Gable, shed, or reinforced flat roof made of plexiglass, that’s also hinged for watering the plants. Extension cord for a very small space heater with great thermostat sensor and controls. Presumably it would need some kind of waterproofing on the subfloor and a small amount of intake/exhaust, accounting for outside air temp hopefully. It’s only meant to last for 1-3 years, so upmost build quality isn’t a priority. Poor ventilation won’t bother me if I can’t make it work easily enough. Would prefer to build it well, and tight enough to keep out pests, and also not have the space heater running 24/7 trying to maintain temp.

Or is there some kind of bullshit greenhouse thing I should just buy from Amazon that will be good enough to keep the warmth in? And do you know which one would work?

Don’t need to plants to produce during the winter. Minimum need is dormancy.

Interested to hear of any of you also garden and have the same problem.


r/buildingscience • • 1d ago

Tips for insulating rim joist? Cold climate.

Thumbnail gallery
5 Upvotes

r/buildingscience • • 1d ago

Patio Lights with Living Space Above

1 Upvotes

I have outdoor patio with enclosed living space above. The patio ceiling is zip sheathed and taped and air sealed. How do I add lighting to the ceiling without compromising air tightness? The only option I can think of is to have wafer led lights -do they have drivers? Or is there a way to install 3" deep recessed LED COB lights? The fixtures are airtight but I am worried the installation will create small gaps at each installation especially with a 3" hole in zip.


r/buildingscience • • 1d ago

Rolled vs blown in

Thumbnail reddit.com
0 Upvotes

r/buildingscience • • 1d ago

*Seeking insulation advice for post-war weatherboard house (Sydney climate, no roof cavity)*

Thumbnail gallery
2 Upvotes

r/buildingscience • • 1d ago

Question Insulated False Ceiling in Shed?

Thumbnail gallery
1 Upvotes

How can I do this without condensation? Is it OK to attach ten foot rafters to the sides of concrete block walls (I think it's 4" blocks, 4" foam, 2" air, 4" blocks)?


r/buildingscience • • 2d ago

Cellular Shades, inside or outside mount for optimal insulation?

1 Upvotes

2 of the big online shops for window treatments say the exact opposite of one another regarding which is preferable if insulation is the top priority. Blinds.com says inside. Simply Blinds says outside. Does it much matter? If so, which is actually preferable?


r/buildingscience • • 3d ago

Drafty house this winter? Here's a free way to find leaks yourself before paying for a blower door test

101 Upvotes

Disclosure: I'm with a building science company in the western Chicago suburbs, but this is a DIY check you can do on a cold, windy day.

  1. Close all windows and exterior doors.
  2. Turn on every exhaust fan you have (bath fans, range hood on high) and the clothes dryer on air-only. This slightly depressurizes the house, a poor man's blower door.
  3. Light an incense stick (carefully) or hold a damp hand near likely leaks and watch for air movement:
  4. - Outlets and switch plates on exterior walls
  5. - Baseboards and where the floor meets the wall
  6. - Attic hatch or pull-down stairs
  7. - Fireplace damper
  8. - Basement rim joist (where the house framing sits on the foundation)
  9. - Plumbing and wiring holes under sinks
  10. Write down what you find. Foam gaskets, caulk, and weatherstripping handle a lot of the small stuff.

What DIY can't do is measure total leakage or find the big hidden bypasses in the attic floor, which are often the largest. That's what a real blower door test is for, and testing again after sealing is the only way to know it worked.

⚠️ Safety before the fan test: if you have a gas water heater, furnace, or boiler that vents up a chimney, set the water heater to "Pilot" or "Vacation" and turn the thermostat down so nothing fires during the test. Don't test while a fireplace or wood stove is in use. Depressurizing the house can pull exhaust back down the chimney (backdrafting), which can bring carbon monoxide inside. Keep the test to 10 to 15 minutes, have a working CO detector nearby, and switch everything back on when you're done.
If your attic has loose, pebbly, gray-brown insulation (vermiculite), skip this test. Vermiculite may contain asbestos, and lowering the house's pressure can pull dust from the attic into your living space. Have it professionally tested first.
Other hazards worth knowing about:
**Vermiculite or old insulation in the attic.**Lowering the pressure pulls air through every ceiling gap, along with whatever dust is up there.
Fireplace ash and soot. Even with no fire going, air can come down the chimney and blow ash into the room. Close the damper or glass doors.
Crawlspace or basement air. Depressurizing pulls air up from below. That can bring in musty air, soil gases like radon, or spores from areas with microbial growth. This matters more in homes with known moisture problems.
Dry floor drains and sump pits. If the water in a floor drain has dried up, sewer gas can come in. Pouring water down unused drains first helps.
Incense or candles. It's an open flame near curtains while the house has a breeze. Use a damp hand or a lightweight tissue instead if you can.
An attached garage. If a car has run recently, exhaust can get pulled in through the garage-to-house door.

Happy to answer questions in the comments.


r/buildingscience • • 2d ago

Double insulation?

1 Upvotes

I’m in the process of finishing my basement, which is already insulated with R13 faced fiberglass, installed tight to the subfloor above with the paper facing down towards the basement. We want to add rockwool for extra sound control from the living space above. Should I be concerned about moisture in the air gap between the two types of insulation? We will have 2 layers of 5/8 drywall on the ceiling. Located in VA


r/buildingscience • • 2d ago

Insulating headers in furnace room on interior "ish" wall - Canada

Thumbnail reddit.com
1 Upvotes

r/buildingscience • • 3d ago

Safe, non-toxic way to insulate rim joists before winter? (Northeast Ohio)

3 Upvotes

Hi everyone, we just finished cleaning up mold and mice in my mom’s split-level crawl space and kitchen. All the old insulation had to be thrown out, and now the house is freezing.

We plan to get the crawl space sealed up professionally later, after we dig up and waterproof the outside of the house. For now, we just want to insulate the rim joists (the wood edges around the ceiling of the crawl space) to keep the cold out.

Here is what we want to do:

- No spray foam or foam boards (we want to avoid toxic fumes). We want to use something safer like Rockwool or sheep's wool.

- Seal the wood cracks with mold-free wood caulk (like DAP Dynaflex Ultra).

- Put the wool insulation in, then cover it with 6-mil plastic sealed tight with acoustic sealant and staples.

My questions:

  1. Even if we seal the plastic super tight, could it trap moisture against the cold wood and cause water droplets (condensation) or new mold?
  2. Should we skip the plastic and just leave the Rockwool open to breathe, or use a breathable "smart" vapor barrier instead?
  3. Is it okay to insulate the rim joists now before we dig up the outside later?

Thanks for the help!


r/buildingscience • • 3d ago

Question Insulating an old garage

Thumbnail
gallery
12 Upvotes

Bought a house with an old garage building. Wondering if it’s worth my time/money to make it usable as an insulated workshop. Or if it’s just a teardown and use as storage for now

Climate zone 5 or 6 I think? Southern Ontario

Can see the air gaps in the siding. Thought about adding insulation batts but a wind driven rain could get them wet i’m thinking. Maybe tyvek each stud bay first, and put insulation overtop.

And yes it needs a concrete floor poured

Any advice/ideas much appreciated!


r/buildingscience • • 3d ago

How can this odd wall be insulated? 1995 era Michigan house

Post image
0 Upvotes

House walls are mostly drywall, then wall frame, then sheathing. In some spots, where there are bump outs/overhangs, the frame changes to drywall, wall frame, then a gap that is insulated on top by fiberglass, as seen in the photo. Beyond that point is what appears to be another wall frame, then house wrap, and then sheathing. Is there any reasonable way to air seal these oddly framed walls against air leakage into the attic?


r/buildingscience • • 4d ago

Question Cathedral Ceiling/Roof Assembly strategy : inquiry

Thumbnail
reddit.com
2 Upvotes