r/diySolar • • 7h ago

Question Good deal on panels ?

0 Upvotes

I have the opportunity to purchase 16 455W panels for $2,160. This would be a DIY setup. Is it prudent to go ahead and purchase these panels before December? Is this a good price?
Thanks.


r/diySolar • • 23h ago

Question Has anyone here ever had to.... From Homeless, Built solar off scraps ?

0 Upvotes

Sorry, that was rude. From a $100 budget.. What do You understand? If we can get past the Sun is real... I would like to have a conversation. I've done it, I could do it 12 years ago. At a campground.

So I'm interested in what y'all consider diy ??


r/diySolar • • 2h ago

Hacking the NEP BDG-256 Gateway (or How I learned to Stop Worrying and Love the AI)

Thumbnail
0 Upvotes

r/diySolar • • 6h ago

a system to charge a 69kwh car battery

0 Upvotes

Guys I am a total noob in this. I have an EV and I am wondering how possible is to charge the EV using solar energy. I only use the car in weekends so that there is a lot of time to charge the car midweek. do you think a setup like this is doable? would it be worth to do this system as full of grid or hybrid?

since the size of the battery car is big, I am having a hard time understanding how the solar energy can be managed so that it can charge the car, for example in an off grid system.

I am inclined for an off grid system so it can be as independent and autonomous as possible.


r/diySolar • • 4h ago

Dead inverter on my Anker Solix S2000, how can I reuse the 2 big cells (6V, 2000Wh) and the working USB ports? Cuba, tiny budget

Thumbnail
gallery
4 Upvotes

Hi everyone, I'm in Cuba, where we have grid power only ~2 hours a day (and it's very unstable), so I depended on my Anker Solix S2000 a lot. Its AC inverter died, and I can't fix it. I'd like to get some use out of the hardware that still works without spending much money (parts are hard to get here).

What happened

On Oct 11 the AC LED started turning off and the inverter shut down after a few minutes. It was plugged into the grid in UPS mode, battery at 100%, no alert icons.
Then it stopped charging from AC, even with the battery at 76% and the outlet live. Solar charging still works fine.
Now the inverter never turns on. The AC button LED just blinks (the manual says this means an AC output fault). I no longer hear the inverter relay click. When I plug AC in, the screen turns on and sometimes shows a red Overload.
I did a reset with the clip.
Two repair shops checked it. The first measured the inverter bridge components and found them fine. The second concluded it's a software problem.

What I checked myself (opened it up)

Glass fuse: continuity OK.
Relay coils measure 357 Ω, 349 Ω and ~100 Ω. The big black relay (Sanyou SFK-112DMP-F-H-3) has open contacts at rest, and its coil reads 101 Ω.
33 Ω cement resistor: OK.
All internal AC wiring has continuity.
Batteries: 2 prismatic cells in series, 3.3 V each (balanced), 6.64 V for the pack, ~2000 Wh total. [Cell brand/model/Ah and chemistry, LiFePO4? Add what's printed on them.]

What still works

The USB ports, including the USB-C (up to 20V).
Solar charging.
The cells themselves seem healthy.

What I have
A separate 12V inverter.
A multimeter.
One solar panel (575 W)

What I want to do
Use the cells and USB ports to power things during blackouts: fans, lights, charging a laptop and phones.
Find a way to run my 12V inverter from this energy. I know 6V isn't enough for a 12V inverter, so I'm considering a 6V→12V boost converter for small loads, or a USB-C PD trigger set to 20V followed by a buck converter to 12V.
Keep it cheap and simple, and safe.

My questions
Is there a smart way to get 12V out of 2 big cells without buying 2 more matching cells?
Has anyone seen this AC output fault on an S2000 (blinking AC button, no relay click)? Could it really be firmware, and is there any way to fix or reflash it?
Any other creative uses for 2000 Wh at 6V that I'm missing?
I know bypassing the BMS is a bad idea with cells this big, so I plan to add my own fuse and low-voltage cutoff. Photos are in the post. Thanks a lot for any ideas!


r/diySolar • • 22h ago

Would this work?

Post image
0 Upvotes

r/diySolar • • 6h ago

4000 LFP cells for $8200. $100/kwh

Thumbnail gallery
2 Upvotes

r/diySolar • • 11h ago

Misc Safety warning: Anker SOLIX Backup Auto-Switch creates a floating neutral (IT-grid) without a PE-N bond

Post image
8 Upvotes

I’ve been looking closely at the product page and installation instructions for the Anker SOLIX Backup Auto-Switch (63A, 1-phase), and there is a major electrical safety issue that Anker completely fails to mention in their marketing.

On their European product pages, Anker claims you can simply install this switch behind your main breaker using "just two cables" to get whole-home backup power. If an installer or DIYer actually wires it strictly according to Anker's simplified instructions, it creates a hazardous situation.

Here is what actually happens when the grid goes down:

  1. No automatic PE-N bond (Floating Neutral): When the Auto-Switch disconnects the house from the public grid (2-pole disconnect of L and N), the neutral (N) is completely isolated from the utility's transformer ground. Because neither the Solarbank Max nor the Backup Auto-Switch has a built-in grounding relay to bond Neutral to Protective Earth (PE) during island mode, your home shifts into an ungrounded IT-grid with a floating neutral.
  2. RCDs (Earth Leakage Breakers) stop working: Without a PE-N bond in island mode, there is no return path to the inverter for fault currents. Standard 30mA RCDs (GFCI/aardlekschakelaars) in your consumer unit will not trip if someone touches a live wire or if an appliance develops a ground fault. Furthermore, sensitive appliances like modern gas boilers (with ionization flame sensors) will often throw an error or refuse to run on a floating neutral.
  3. Missing local ground electrode requirement: For homes with a standard TN-S or TN-C-S grid connection (where earth is supplied by the utility company), switching to island mode under European electrical codes (IEC 60364 / NEN 1010) requires a local earth rod with a sufficiently low resistance, paired with an external relay that automatically bonds N to PE only when off-grid. Anker mentions none of this—only a vague one-liner that the unit "must be properly grounded."

Conclusion:
Unlike proper hybrid inverters (which include an internal N-PE grounding relay that engages during off-grid operation), the Anker Backup Auto-Switch is just a basic transfer switch with a built-in CT meter. Selling this as a plug-and-play "whole-home backup solution" without warning installers about external N-PE bonding and local earthing requirements is misleading and unsafe.

I have already reported this directly to Anker's support/compliance team. Curious to hear if anyone here has installed one and how your electrician handled the N-PE bonding during island mode!