r/reloading • • 3h ago

I have a question and I read the FAQ Area 419 zero gen 1

1 Upvotes

I have the opportunity to purchase the gen1 zero press off a buddy for a decent discount. But was wondering if I should shell out the extra money for the gen 2.

I'm completely new to reloading, and only wanted the area 419 because I'm a shill for their products.


r/reloading • • 22h ago

Newbie Reloading Newbie

1 Upvotes

I’m looking to get into reloading. I have purchased some components to begind reloading my 6.5 Creedmore rounds. My question is do all the components need to match the reloading books? For example what if my bullet isnt the same as what’s in the manual. I’m trying to load some cheap stuff to get use to it. (Speer Hot Core 140 gr, Hornady LRP Brass, CCI 200 primers, H4350 Powder). I could use some advice on this and mix and matching components as well.


r/reloading • • 13h ago

Newbie 3.350” COAL on 30-06 safe?

2 Upvotes

Hey everyone—sorry in advance for the long post.

I’m reloading for a Winchester M1917 Enfield using Speer 150gr bullets (part #2022) and IMR 4895 powder, and I’m getting a 12–13" spread at 100 yards (with some charge weights even worse). I’ve tried different powders and bullet brands and keep getting the same results. But when I shoot commercial brand like Rem CoreLokt, Super X, etc. it’s completely fine. So I verified that it’s not the rifle.

Right now, I’m seating the bullets to the manual's listed COAL of 3.250". After doing some research, I realized my seating depth might be way too short, leaving a huge jump to the rifling. To find my rifle's max COAL, I took a fire-formed case, barely started a bullet in the neck, and gently chambered it 4–5 times. Every time, it came out right around 3.380" (give or take 0.005").

Since SAAMI max is 3.340", am I safe to go above SAAMI max as long as I know what my rifle's max COAL is (like starting around 3.350")? I’m still relatively new to reloading and want to make sure I’m heading in the right direction before loading up a batch. Thanks!


r/reloading • • 17h ago

Look at my Bench My 650 spontaneously multiplied!

Thumbnail
gallery
47 Upvotes

Still lots of set up to do, but it was nice to see it with a twin.


r/reloading • • 18h ago

Newbie First run through Frankford wer tumbler

Post image
102 Upvotes

Decided to get into reloading and bought a reloaders estate setup. Presses were seized but been refurbishing them and almost ready to start reloading but ran a wet tumbler on range brass with wash & wax and citric acid. Its gorgeous!!!


r/reloading • • 36m ago

Load Development Discontinued Powder Equivalent for 9mm Steyr Loads

Post image
2 Upvotes

r/reloading • • 4h ago

Load Development Dead Nuts 147gr DFN Seating Depth and Load Data

2 Upvotes

Looking to see if anyone else loads these projectiles at all. I haven’t seen many mentions of them elsewhere and was looking for additional data. Current load:

Mixed brass, 6.3gr Accurate no 7, CCI 550 primers, COAL 1.085-1.095. Averaging about 930fps through a Glock 19.

I’ve found I have to seat them deeper to pass the plunk test in a Glock 19 Gen 6. They tend to bulge a bit until I run them through a Lee FCD. After that, they have some pretty heavy marks


r/reloading • • 15h ago

Load Development 45-70 Trapdoor Smokeless

2 Upvotes

I have an original 1888 Springfield Trapdoor that I want to reload for. I’m using Starline brass and cast 405g bullets. I have IMR 4198 at home that I’d like to use but I have trouble finding information regarding how much powder to use and what primers are recommended. Any advice would be greatly appreciated as I am new to reloading.