r/reloading • • 37m ago

Load Development Discontinued Powder Equivalent for 9mm Steyr Loads

Post image
2 Upvotes

r/reloading • • 3h ago

I have a question and I read the FAQ Area 419 zero gen 1

1 Upvotes

I have the opportunity to purchase the gen1 zero press off a buddy for a decent discount. But was wondering if I should shell out the extra money for the gen 2.

I'm completely new to reloading, and only wanted the area 419 because I'm a shill for their products.


r/reloading • • 4h ago

Load Development Dead Nuts 147gr DFN Seating Depth and Load Data

2 Upvotes

Looking to see if anyone else loads these projectiles at all. I haven’t seen many mentions of them elsewhere and was looking for additional data. Current load:

Mixed brass, 6.3gr Accurate no 7, CCI 550 primers, COAL 1.085-1.095. Averaging about 930fps through a Glock 19.

I’ve found I have to seat them deeper to pass the plunk test in a Glock 19 Gen 6. They tend to bulge a bit until I run them through a Lee FCD. After that, they have some pretty heavy marks


r/reloading • • 13h ago

Newbie 3.350” COAL on 30-06 safe?

2 Upvotes

Hey everyone—sorry in advance for the long post.

I’m reloading for a Winchester M1917 Enfield using Speer 150gr bullets (part #2022) and IMR 4895 powder, and I’m getting a 12–13" spread at 100 yards (with some charge weights even worse). I’ve tried different powders and bullet brands and keep getting the same results. But when I shoot commercial brand like Rem CoreLokt, Super X, etc. it’s completely fine. So I verified that it’s not the rifle.

Right now, I’m seating the bullets to the manual's listed COAL of 3.250". After doing some research, I realized my seating depth might be way too short, leaving a huge jump to the rifling. To find my rifle's max COAL, I took a fire-formed case, barely started a bullet in the neck, and gently chambered it 4–5 times. Every time, it came out right around 3.380" (give or take 0.005").

Since SAAMI max is 3.340", am I safe to go above SAAMI max as long as I know what my rifle's max COAL is (like starting around 3.350")? I’m still relatively new to reloading and want to make sure I’m heading in the right direction before loading up a batch. Thanks!


r/reloading • • 15h ago

Load Development 45-70 Trapdoor Smokeless

2 Upvotes

I have an original 1888 Springfield Trapdoor that I want to reload for. I’m using Starline brass and cast 405g bullets. I have IMR 4198 at home that I’d like to use but I have trouble finding information regarding how much powder to use and what primers are recommended. Any advice would be greatly appreciated as I am new to reloading.


r/reloading • • 17h ago

Look at my Bench My 650 spontaneously multiplied!

Thumbnail
gallery
47 Upvotes

Still lots of set up to do, but it was nice to see it with a twin.


r/reloading • • 18h ago

Newbie First run through Frankford wer tumbler

Post image
102 Upvotes

Decided to get into reloading and bought a reloaders estate setup. Presses were seized but been refurbishing them and almost ready to start reloading but ran a wet tumbler on range brass with wash & wax and citric acid. Its gorgeous!!!


r/reloading • • 22h ago

Newbie Reloading Newbie

1 Upvotes

I’m looking to get into reloading. I have purchased some components to begind reloading my 6.5 Creedmore rounds. My question is do all the components need to match the reloading books? For example what if my bullet isnt the same as what’s in the manual. I’m trying to load some cheap stuff to get use to it. (Speer Hot Core 140 gr, Hornady LRP Brass, CCI 200 primers, H4350 Powder). I could use some advice on this and mix and matching components as well.


r/reloading • • 1d ago

Newbie Beginner Reloading Ideas

0 Upvotes

If you were to start reloading as a complete beginner all over again and you have a newbie progressive press, tumbler and bullet feeder what’s one item you would add to upgrade your kit? Or what’s one piece of kit that you would add quickly?

Basically asking for gift ideas for a new reloader.

Thanks all


r/reloading • • 1d ago

Gadgets and Tools In stock source for Tempilaq 750 degree?

1 Upvotes

Does anyone know of a source for 750° Tempilaq?

Everywhere I have looked it is backordered. The only thing I have found a couple of price gougers wanting $60+ plus shipping


r/reloading • • 1d ago

It’s Funny Random Doomsday Prepping - Reloading Supplies

0 Upvotes

Due to the recent apocalyptic chaos of the FAA, I started to think deeper about John Connor and Judgement Day (yes Terminator GIF's and quotes are all encouraged). In particular what's your plan for reloading gear and provisions should you have to become nomadic. I can understand the hunker in the bunker mentality with a stockpile to last generations, but what if that is not possible. Are you only taking ammo that you can wheel around in your red radio flyer wagon? Are you lining pack mules up like the Columbian coffee farmers to haul the 6 tons of lead, primers, powders, and steel presses you've acquired through the years. Or you going old school with the Lee hand press?


r/reloading • • 1d ago

I have a question and I read the FAQ Once Fired NAS3 (556)

Thumbnail
gallery
42 Upvotes

Has anyone attempted to reload NAS3 556 casings?


r/reloading • • 1d ago

Newbie Buy once Cry once has entered the chat

Thumbnail
gallery
71 Upvotes

Ive only been at this reloading thing for 9 months and I’m already never going to financially recover from this!

Absolute over kill for my needs and purposes? Yes but damn is it convenient.


r/reloading • • 1d ago

Load Development .357 Magnum Duplex Load

Thumbnail
gallery
335 Upvotes

Got thinking one day “What if I load two buckshot balls into a .357 casing?” And turns out Remington and a few others already did that way back when. So I decided to give it a go and this is what I came up with. Two .350” lead round balls from Hornady on top of 15gr of compressed H110. Velocity of the 130gr total payload averages 1086.6 FPS out of my 4.2” barrel Ruger GP100 equaling 340ft-lb between the two projectiles. I think the velocity would be much higher if the diameter of the projectiles was .357” but .350” is the only commercially made round ball I could find that would fit the .357 Magnum casing. Hornady’s .375” round balls did not fit. So to get them to fit, I ran them through a .357” sizing die. While this worked to get them to the right diameter, they would not seat straight in my seating die due to the two round ends of the projectiles contacting one another. Spread of these .350’s was anywhere from 2” to 4” at 15 yards which is pretty good to me. They’re neat to say the least.


r/reloading • • 1d ago

Hunting Results Hunting load NSFW Spoiler

Thumbnail
gallery
26 Upvotes

Well the load is developed did well today! She was 25 yards out, the bullet was poking out the opposite side, broke through a rib on each side. Might take them up in velocity just a little for next time.


r/reloading • • 1d ago

I have a question and I read the FAQ Cheap Chronograph

0 Upvotes

Whats a nice cheap chronograph I can buy for measuring bullet speeds? Do the £30 Air rifle ones work?


r/reloading • • 1d ago

Stockpile Flex Rainy day fund

Thumbnail
gallery
145 Upvotes

r/reloading • • 1d ago

I have a question and I read the FAQ Starting from scratch. Reloading only 6.5 CM

0 Upvotes

Starting from scratch with no equipment, what's the cheapest reasonable setup for reloading 6.5 Creedmoor, start to finish? Thanks in advance!


r/reloading • • 1d ago

Something Unique(Vintage/wildcat/etc) World’s first footage of the 45 auto-stopper being fired (from a MAS 1873)

92 Upvotes

After showcasing what seemed to be the world’s first footage of the Webley 455 manstopper being fired, I figured I would try and duplicate a safe version for antiques/webley’s in the 45ACP case, for those of us who have shaved Webley’s or reamed MAS 1873’s.

While I can’t upload both a video and a picture, the target itself had some pretty gnarly impact holes (I see why the 455 manstopper was banned for wartime use).

Both the 455 webley and the 45 autostopper loads are detailed below:

455 manstopper: 230gn Hollow Base .455 Manstopper cast with MP-MOLDS Manstopper 4 cavity mold, pure lead, Eastwood jet black powder coat, sized to .451, 3.3-3.5gn of Unique, OAL 1.13, seated depth 0.20, Fiocchi Webley mk2 brass with federal small pistol primer. Tested in a MAS 1873 4.5” barrel from 1875

45 autostopper: 230gn Hollow Base .455 Manstopper cast with MP-MOLDS Manstopper 4 cavity mold, pure lead, Eastwood jet black powder coat, sized to .451, 3.5gn of WIN 231 , OAL 1.22, seated depth 0.20, mixed range 45ACP brass with CCI large pistol primer. Tested in a MAS 1873 4.5” barrel from 1875


r/reloading • • 1d ago

I have a question and I read the FAQ Reuse of Factory Brass

Post image
63 Upvotes

Tried to search the subreddit for this and it was full of people asking if they could, and subsequently people answering they do but only certain brands...
I have been reloading brass from random boxes of ammo with no issue from what I can tell. The Blazer cases I have in the picture I have reloaded 4 times. Is this one of those preference debates or is there really "good" and "bad" brands of brass to reload?


r/reloading • • 1d ago

I have a question and I read the FAQ Are these brass cases usable?

1 Upvotes

One of my cans of .45 LC was left open for a few years on shelf. The top layer have this discoloration. Is it simply cosmetic, or has the brass been weakened? Will they damage my resize and decapper die? I use light loads in my .45 colts, and my cheap ass doesnt want to throw 35 of these out. I already ran them through my tumbler with nu finish.

Sorry forgot to post a pic, I added it below


r/reloading • • 2d ago

i Have a Whoopsie 38 special squib loads

0 Upvotes

Fairly new to reloading, I pressed a about 25 38 special rounds using. Starline brass, Winchester small pistol primers, and 3.8 grains of HP-38. I was shooting out of my lever action rifle, and had a few squib loads. Any recommendations on how to fix this? Appreciate any feedback


r/reloading • • 2d ago

Load Development HP-38 powder question

7 Upvotes

I would like to buy some commercial 357 rounds, made with HP-38. If I got them and they shoot well, I’d like to try to make similar rounds.
Any ideas of who might manufacture units with Brass, magnum primers, and 125 or 140 bullets?


r/reloading • • 2d ago

Newbie Feedback on my 9mm reloading

Post image
23 Upvotes

Hey everyone, looking for feedback on these 9mm reloads. Using Brass Monkey coated bullets 137, Titegroup, and CCI primers on an RL 1100. I'm getting good consistency and they all case guage ok.

However, the cases (9mm) appear slightly deformed after sizing on my RL 1100. Could improper die setup be causing uneven pressure that distorts both the brass and the seated bullet? Any suggestions on what i should look into would be great.


r/reloading • • 2d ago

Load Development 25-06 Load Development

1 Upvotes

Looking for some guidance on a load i am trying to put together.

25-06

Sierra 117gr Game Kings

Vihtavuori N165

If anyone has tried this before I would appreciate your incite

Looking more for percision over velocity

Also how far are you normally seating off the lands?