r/sffpc • • 6h ago

Build/Battlestation Pics Rate my tiny travel pc

Thumbnail
gallery
9 Upvotes

My Specification

Cpu: Ryzen 7 3700x

Gpu: Msi Rtx 5060 8gb

Ram: Fury 32gb

Mobo: Asrock 550m itx/ac

M. 2: Wd Black Sn850x

Psu: Lian Li 850w


r/sffpc • • 14h ago

Build/Parts Check Rate my first SFF parts list?

Thumbnail pcpartpicker.com
1 Upvotes

Go ahead and give any honest thoughts. I’d appreciate feedback now so I don’t regret anything in the future.


r/sffpc • • 15h ago

Assembly Help Ncase M2 question

1 Upvotes

Just did a build in the M2, but while gaming I ran HWINFO & saw my chipset hits 73c & the ssd hits 68-70c. Also, my ram hits temps of 58-60c. How are you guys managing to cool the ram? I had trefi at 65535 thought that might be the issue & swapped it back to 32767 temp lost -1c. Any tips on how I can possibly have a ram fan in there?

For reference, I have an Astral 5080 in the build.
Or am I overthinking these temps for normal gaming use. Thanks!


r/sffpc • • 18h ago

Build/Battlestation Pics NFC 4TF Mk. 3.1

Thumbnail
imgur.com
29 Upvotes

Fully 3d-printed 4TF extra-long. I used NFC Josh’s MkIII, and added another 10mm of chassis and panel stretch with splices in the slicer. I added mesh sections as well to let pieces breathe better. I also used the motherboard tray from the 3DLP chassis and cut it to size in the slicer - that’s the lime peeking out to the left of the SO-DIMMs. This allowed me to run two Arctic P9 Max fans as front intakes, which produce an insane amount of static pressure if full load is needed. CPU intake is a Gen 1 Arctic BioniX. Yes, I know the lime is gaudy. Yes, I’m aware it’s not everyone’s cup of tea. Yes, Snorlax is the best Pokemon. The lime is almost a perfect match for Corsair yellow though, so it’s a nice little color pop.

Build as set up:
- Minisforum 790i 7945HX3D, -25 all-core undervolt, boost +150 core
- 64GB Crucial SODIMM, OC to 6000. CL is still dog water at 46, but the best available is 40 at lower frequency mhz.
- Vastarmor 9060XTLP at time of photos, thanks to a friend loaning it. -100mv, +150 core boost, +2850 memory, no change to board power limit. It’s replaced with a monster of a binned 5060LP that runs like a scalded dog.
- Enhance 8345 450W Platinum PSU
- 2x 2TB Predator GM7000 NVME SSDs


r/sffpc • • 7h ago

Build/Battlestation Pics T1 Reference Deep-ITX Build

Thumbnail
gallery
125 Upvotes

CPU: AMD Ryzen 9800X3D
GPU: RTX Pro 5000 Blackwell 72GB
Motherboard: ASRock Rack AM5D4ID-2T/BCM Deep mini-ITX
Ram: 32GB Gskill Royals @ 6000c26
SSD: Sabrent Rocket 1TB
PSU: Corsair SF850 w/ zcooi cables
Cooler: Thermalright AXP100 Full Copper w/ noctua fan
Case: FormD T1 reference V2.0 - TG side panel

Currently running qwen 3.8 27B q8 for local inference. Also using this for gaming - roughly 5080 performance. Runs cool and quiet.


r/sffpc • • 5h ago

Build/Battlestation Pics My oncall companion

Thumbnail
gallery
114 Upvotes

Not the best setup but it gets the job done


r/sffpc • • 23h ago

Build/Parts Check AXP90x47 in NCase T1 - questions on fan modding with duct

3 Upvotes

I know there are variations of this thread on here, but I'm trying to get a solid answer on something.

I am planning to use the axp90x47 with a regular Noctua 92mm on a 9800x3D build. I know this doesn't necessarily improve temps but can improve acoustics.

I have also seen people who make a 120mm fan adapter duct (not just a flush mount, but a duct to better force air through the cooler). I think with my parts, I can squeeze in a 2 or 3mm tall duct

Has anyone tried this solution? If no improvement in temps, is there an even better reduction in noise? I'm aiming for silent during day to day tasks and no jet engines during gaming.


r/sffpc • • 4h ago

Assembly Help [Parts Check] DIY Custom Cables for Thorzone Nanoq S + Corsair SF850 (Type-5)

2 Upvotes

Hi everyone,

I recently bought a Thorzone Nanoq S (which is supposed to ship today!) to downsize from a Lian Li B4. Because of my ASUS Prime RX 9070 XT and its three 8-pin PCIe connectors, I'm planning to make my own custom PSU cables to avoid a nightmare with cable management.

Based on the Thorzone Nanoq S custom cable manual (https://thor-zone.com/mini-itx/nanoq/), I put together a parts list from ModDIY for my Corsair SF850 (2024). I'd love to get your feedback or recommendations before ordering (every connector comes with his pins):

Motherboard cable:

CPU Cable:

GPU cable:

With:

  • Total of 15.2m of cables
  • 20-30 ATX female eps pins (the connectors already come with their own pins, so these are just spares in case I mess up a crimp)
  • 20-30 Micro fit female connectors (just spares)
  • Wire crimping tool
  • Wire stringer tool
  • Pin remover (or just a paper clip)

A quick question regarding the wire: Has anyone used ModDIY's 16 AWG soft silicone wire with Corsair Type-5 (Micro-Fit 3.0) connectors? Since Micro-Fit housings are pretty tight, I want to make sure the outer diameter of the 16 AWG silicone insulation isn't too thick to fit properly into the PSU-side connectors, or if I should step down to 17/18 AWG instead.

Does everything look accurate and compatible, especially regarding the Type-5 pinouts and terminals? Thanks in advance!


r/sffpc • • 4h ago

Build/Battlestation Pics Should I take out my GPU and cooler for carry-on plane luggage?

Thumbnail
gallery
7 Upvotes

Hi, recently I've built my own SFF. It's SSUPD Meshroom D, 15L case.

The build was considered transporting in the first place, due to I have to move between countries several times a year and my laptop died. So here's how it went:

CPU: Ryzen 7 9700x

Cooler: Thermalright SS110 (for a really light weight of 500g and small dimension for less twisting torque)

RAM: Lexar 48gb 6000MT/s CL30

MB: MSI MPG X870i edge Ti WiFi

GPU: Asus Prime RTX5070Ti OC (for less thickness and weight)

PSU: Deepcool PS850P

It worked great, and it wasn't that heavy at all. It's my time for transportation, I've added a metal GPU bracket to (not very tightly) clamp the GPU from the other side, stuffed foam under and around GPU to make it as stable as possible. I also stuffed foam all around my luggage case and stuffed some clothes as well. The whole luggage case is only for the Meshroom D basically, and the PC is definitely not moving afaik when dragging the luggage case inside my house.

Now, I'm trying to carry this luggage on the plane, I'll handle this luggage as carefully as I could, and I'll 100% not check in due to some horrible movements I've seen. However, I've saw people claiming that you should always take out your GPU and CPU cooler or it will definitely gonna fail. Like they say your PCIE is gonna break, your MB will be twisted, your CPU could get removed from the socket together with the cooler, like that.

Should I really take my GPU off in this case? It would be a hassle to do this and actually defeats the purpose of ITX. But, I don't really want to risk my GPU especially considering the price nowadays. What should I do?


r/sffpc • • 18h ago

Build/Parts Check I plan to buy motherboard with x8/x8 bifurcation option. Does MSI MPG X870I EDGE TI EVO support this feature?

Thumbnail
reddit.com
3 Upvotes

r/sffpc • • 19h ago

Assembly Help Dan Cases A4-SFX – experiences with 92mm AIO on 9800X3D?

1 Upvotes

I'm planning a refresh in my A4-SFX and considering a 92mm AIO for the 9800X3D instead of the usual air cooler. Main goal is lower noise under sustained loads without losing too much cooling headroom.

I’ve seen a few people run similar setups but not many long-term reports on pump noise or VRM temps in this specific case. If you’ve tried it, how did the acoustics and thermals turn out compared to a good air cooler like the Noctua NH-L12 or AXP90? Any particular AIO you’d recommend or avoid?