r/DIY • • 5h ago

help How could tell which wire is positive and negative?

32 Upvotes

I have a broken e-bike rear light. The cable on it was pulled off.
https://imgur.com/UdYKD8L

https://imgur.com/edSihvf

Now I am trying to fix it by maybe bridging the missing wire and wrapping it in electric tape because I dont have a soldering iron.

My 2 question is; how can i tell which wire is positive and negative? The wires are coloured solid black and black with white stripe.

Additionally, will I need a specific type of wire to bridge it or can I just use any random wire since I have a bunch or spare usb charging cables that I can just cut up and salvage the wire inside of it?


r/DIY • • 7h ago

woodworking DAP Plastic Wood for nail holes

24 Upvotes

Maybe this is a case of me looking for something better when what I have is working fine, but I will throw it out there. I am installing a bunch of trim that is white finger joint pine. It is primed but I put a coat on it before installing then put a second coat on after it is installed and caulked/filled. I have just been using the natural color DAP Plastic Wood and I guess it works fine, but that is all I have tried. I put it on with a putty knife, sand it, spot prime, then give another coat. It seems to work fine, but then again, maybe I don't know if it is or not since I have nothing to compare it with.


r/DIY • • 3h ago

woodworking 1980s Florida home — Wood framing against concrete block walls is wicking moisture (13–17%). Mold found. How do I permanently fix this?

7 Upvotes

I recently purchased a home built in 1983 in Tampa, Florida, and I’m trying to figure out the correct way to address moisture along the bottom of my exterior concrete walls without spending thousands on the wrong solution.
The house has thick concrete block exterior walls with wood framing installed against them, insulation, and drywall.
During some remodeling, we discovered moisture and mold behind the baseboards along the exterior walls. We had mold testing performed, which identified Stachybotrys in some of the affected areas.
Here’s what we’re seeing:
● The tile floors themselves are testing dry.
● The wood framing/baseboards against the exterior concrete walls are measuring approximately 13–17% moisture content, with some areas as low as 9.6%.
● The higher readings tend to be near windows and along the bottom of the walls.
● We found some dark mold growth around nails and along the bottom of the wood.
● The concrete walls themselves don’t appear visibly wet.
● Indoor humidity is generally around 45–55%.
● Some of the mold appears to be historical, but I’m trying to determine whether moisture is still entering.
My theory is that the wood is absorbing moisture directly from the concrete block walls, or that humid air is condensing inside the wall cavities.
This is Florida, so the outdoor humidity is obviously high much of the year. I’m concerned that even if I replace all the affected wood and drywall, the same problem will happen again unless the wall assembly is corrected.
I’ve had contractors offer to waterproof/seal the exterior foundation and lower concrete walls, but I’m not convinced that’s the actual source of the moisture. I don’t want to spend $10,000–$16,000 on foundation waterproofing if the problem is really condensation or moisture wicking from the concrete.
My questions for anyone experienced with Florida concrete block construction:

  1. Is it normal for wood framing against concrete block walls to measure 13–17% moisture in Florida?
  2. Could this be capillary moisture transfer from the concrete into the wood rather than an actual foundation leak?
  3. How do you properly separate wood framing from concrete block walls to prevent moisture wicking?
  4. Should there be a vapor barrier, rigid foam insulation, sill gasket, or some other material between the concrete and wood?
  5. How do you prevent condensation inside these wall cavities when the AC is running and it’s hot and humid outside?
  6. Would exterior waterproofing help, or could it potentially trap moisture inside the walls?
  7. What’s the proper way to rebuild these walls so they can dry and won’t develop mold again?
    I’m looking for a long-term building-science solution, not just spraying mold killer, painting over the concrete, or replacing wood only to have the problem return.
    Has anyone dealt with this in an older Florida concrete block home? What actually fixed it?
    I’d especially appreciate input from Florida contractors, building-envelope specialists, or anyone familiar with moisture management in hot, humid climates.
    Thanks in advance!

r/DIY • • 4h ago

electronic Converting ceiling fan remote to wall switch

7 Upvotes

We have a ceiling fan and light that is not attached to a switch, and it's kind of a pain. It has a remote, but we have entirely too many remotes that can get lost, and I'd rather have a wall switch. But I also don't want to run a whole bunch of new wiring for it. I'm comfortable working with the wires at the electrical box, and I installed this fan myself, but running new wires through the wall is more than I want to deal with.

I've recently discovered that you can convert single-pole to 3-way switches without running new wiring through the walls, by replacing your original switch with a smart switch. The Lutron version of this comes with a remote that is designed to look roughly like a regular wall switch, and fit into a standard wall plate. I'll definitely be doing this for a couple switches where we've wished for a while we had another switch on the other side of the room.

But is there an easy way to do something similar for my ceiling fan? Lutron has a similar product meant for fans that would do the job if my fan had a regular switch already, but my fan is not currently wired to a switch at all. Do you have ideas for how I can either:

A) Connect a small remote, that fits into a standard switch plate, to the frequencies of my existing remote that came with the fan, like the way universal remotes learn to connect to new devices,

Or B) Connect a new receiver at the ceiling mount, that will enable me to control the fan from a switch plate (or other remote that fits into the switch plate.)

Thanks in advance for any suggestions!


r/DIY • • 6h ago

help Leveling Floor With Epoxy Surface

11 Upvotes

Hi folks! I have a basement floor where there is very old tile that was epoxied over at some point. The epoxy is starting to come up in places and we had the tile and mastic tested for a hazardous material (can't say the word or my post gets taken down). The tile does not have it, but the mastic does (~3% from the test). We want to add some flooring, but from what I read, I cannot use self-leveler since it won't adhere to the epoxy surface. I also don't want to etch the surface and kick up hazardous material into the air. The tile has about a 4-5 in from the wall making it pretty uneven in that area. I am wonder if there is any way to level the floor enough to be able to get LVP in without removing the epoxy and tile under that? Should I just send it with the self-leveler and hope for the best?


r/DIY • • 14h ago

carpentry help with a wall repair, with the chimney behind it

31 Upvotes

My drunken loser ex fell into this wall and broke it. I don’t have the bandwidth to deal with drywall right now, so I’m trying to figure out how to patch this hole. Obviously it’s too big for a patch kit (it’s roughly 1’ x 2’).

It’s in the kitchen and I have a piece of pegboard that would fit over the hole so that I could then hang kitchen stuff.

But I’m wondering about the potential draft behind the drywall. Should I seal the hole up with a solid board (I have some pieces of thin veneer-ish plywood-ish stuff)? Should I put insulation back there and then just put the pegboard over that? Should I close it up with a solid board and then attach some pieces of wood to bump the pegboard out enough so you can get the hooks in?


r/DIY • • 11h ago

other Rodent inspection basics?

10 Upvotes

So the last 2 nights I have been hearing a noise coming from a specific 1st floor air vent. My cats have noticed too! I have done a preliminary outdoor inspection to check if there are any obvious holes in the siding / ventilation but I can't see anything. I really have no idea how a rat would have got into the vent or crawl space but I know they can use extremely small holes.

Any advice on what to check and do before calling an exterminator? I haven't see any droppings or anything but there is definitely something unusual going on. Thanks


r/DIY • • 10h ago

help bleaching clothes in cold weather?

2 Upvotes

hiya, i started bleaching stuff in the summer and really liked it but the colder it got the less it worked lol. ik that bleach works better with warmth? now im looking for a way to continue while its cold but my last attempt didnt react at all... do yall have ideas? couldnt find anything online...
i thoight about *maybe* doing it inside where its warmer or using a hairdryer but i really dont wanna get poisoned by the fumes lol

thanks for helping :)


r/DIY • • 1d ago

woodworking What is the best way to shave 1/8th of an inch off a pine common board?

74 Upvotes

I'm in the middle of a DIY project to add extra shelves to my out of production Kilby IKEA bookcases. So far things have been going pretty well, but out of the 16 shelves I just made and the 32 I already had that I am adjusting, about a dozen were too big to fit in the cases after I started using brackets instead of support columns. I was able to fix about half of the ones that were only slightly off, but I still have at least half a dozen common boards that are about 1/8th of an inch too wide.

I've tried using a metal file and a shaver, but both provide very little progress. I tried to get a rasp, but the only one I found locally was about twice as wide as the boards, and looked pretty similar in design to the shaver. What is my best option here to reduce these boards?

If it matters, this is for common boards (pine I think) that are 25" by 6" by 1" and I am trying to go down to 24 7/8".

Also, I don't really have a workbench I can use. The only friend that has one has it buried at the moment.

UPDATE: Thanks everyone for all the responses!


r/DIY • • 1d ago

Trade tips for garage insulation

38 Upvotes

I’ve been planning to insulate my garage and eventually drywall. The insulation process is pretty straightforward, but what advice or “trade tips” would you share with a DIYer? Is there anything specific about bug or water treatment prior to insulationi? Any advice on more accurate estimation of supplies? Commonly overlooked factors that delay the project?


r/DIY • • 1d ago

help Soundproofing on party wall in rowhome

47 Upvotes

Been living in my current home for the past year and a half. Before I continue on I have talked to the neighbor, it helped some but not all the way. Neighbor has obnoxious barking dogs and I am trying to figure out way to dampen the noise from their house into mine. The reason being is because I work from home and it can get a bit obnoxious being in meeting and hearing the barking. Any suggestions on possible solutions to this issue?


r/DIY • • 1d ago

help How to seal silver sharpie autograph on photo Need help preserving an autograph

67 Upvotes

How to seal silver sharpie autograph on photo

Need help preserving an autograph

I have a photo that was autographed a long time in Silver sharpie. I think the type of Los that it was signed on. Has never allowed it to dry and set. I’m reading online. It could be due with being inkjet. I wanted to find out what type of spray were likewise, I can put on it to preserve it as I plan to get other autographs on this item.

Thanks in advance


r/DIY • • 1d ago

electronic Replacing dimmer with switch on old IKEA floor lamp

23 Upvotes

I have an IKEA RUTBO floor lamp from about 15 years ago which I love, but I want to put LIFX bulbs in it and I can't right now because the lamp has a dimmer switch. This is what it looks like.

It has a fuse, and I understand that it's for safety reasons, but all of the regular ON/OFF switches I can find do not have a fuse. The wire has some markings on it like SPT-2 and 18AWG.

My gut is telling me that they put the fuse there because it's on a dimmer and there's more room for things to go wrong there than on a regular switch, as a safety measure. And that replacing it with a regular ON/OFF switch doesn't need one. But does anyone know? I seriously can not find any regular switches with a fuse.


r/DIY • • 1d ago

help Be honest, when you iron a design on your shirt, is it completely gone after like a few washes..?

20 Upvotes

For his birthday, my friend asked me if I could find a seller for a shirt that has a certain design and I honestly couldn't find a proper one anywhere so I decided to do it myself. But I'm afraid it'd wash away too quickly and easily :c some people said that as long as you turn it inside out and wash it by hand, it's fine, but idk how much I believe that

Any advice?


r/DIY • • 12h ago

home improvement Toxic gas from tub refinishing, bathroom has WALL on window, rainy, not dissipating

0 Upvotes

Not actually DIY, landlord hired someone.

Situation:

  • singular window in bathroom has big tall 'wall' (from which shower head was built from?) 6-10 inches away from the window. There's a sink on one end and something beneath it / there's very little room/access and the 'wall' is also high up. It is effectively blocked off and useless. I have tried to aim air into it, but the small bathroom's design makes this kind of impossible.
  • there's a vent we've been running, but I don't know that it actually works
  • apartment has no centralized air/heat/fans/anything. Narrow hallways, small rooms, no easy airflow.
  • bathtub was refinished. Was told the gases/paint were super toxic. Was told it'd be safe to come back around 2pm. Opened all windows and doors. Repair person brought a big fan, which he's thankfully left me with for now, but it was pushed into the wall/window tiny area while he was here with bathroom door closed, so I don't think any air actually left the bathroom. Came back around 4pm ish, initially thought maybe it was okay, but realized all toxicity initially still trapped in bathroom.
  • Toxic air has slowly been spreading into hallway etc.
  • Rooms / hallways around toxic tub smell like toxic paint. Had made my throat hurt yesterday

Have tried / are trying:

  • Moved into bedroom further away. This room's air feels good/clean
  • have HEPA air filter running in toxic tub bathroom with the fan on, window open as rain allows
  • have another HEPA air filter running, alternating its use between hallway/area outside toxic bathroom and room we sleep in
  • planned to keep all windows open and leave house again today in hopes it'd air out, but it rained all night last night, is due to rain all day today, and is due to rain again all day/night for next 3 days....
  • Room we're sleeping in is "far away", between that, window, and air filter, air feels good here. Immediately feels horrible when bedroom door is open. Kitchen is outside bedroom door and relatively better, but also noticeably toxic when first opening door into other rooms.
  • debating between staying home and opening windows as able with rain and leaving with filters fan etc on. Staying home can mean reduced exposure if staying in faraway safer air room, but means exposure. Not staying home means all windows need to be closed due to rain. Can only open windows for 10 mins or so periodically anyway due to rain, so not sure it's worth it.
  • debating between having bathroom door closed vs open. Open means toxic gases go elsewhere, but closed means it might. never get chance to air out period given window-wall situation. Have bathroom vent on and HEPA filter and fan on in bathroom regardless.

I don't want long term health issues here, obviously. I have no control over the insane design choice they made to put a WALL a couple inches blocking the window (also potential mold issues here because of that, and yeah, not a great landlord on multiple fronts). I have no control over the rain and timing of rain/repair. I'm doing what I can with the HEPA filters and strategic fan aiming and door closings and window openings, but so far, it has NOT been enough. I don't know what constitutes full on unsafe and what's just 'annoying' or 'bad' but not long-term bad. We have no reason to go into the shower-bathroom regardless for a couple days as the tub needs to dry regardless.

Advice on how to get this toxic gas out of our apartment?


r/DIY • • 1d ago

help Garage Punch Bag Recommendations

12 Upvotes

Hi, I'm planning to get a heavy bag and hang it from a concrete block wall in my garage.

Can anyone recommend a quality bag and wall bracket? I'm based in Ireland/the UK.

Thanks


r/DIY • • 2d ago

help My post asking for help has been waiting for moderator approval for two days. Message to mods unanswered.

98 Upvotes

Not sure what is going on. I posted a question and included some pictures to explain the situation.

Did I miss some step or violate a rule?

Here's the original post and pics.

I want to put drywall on a basement wall but it has some quirks that I'm not sure how to manage.

This wall runs under the main beam of my house and aligns with the Lally columns holding up the beam. The problem is that the studs sit about 1 inch inside of the face of the beam and the outside edge of the column(s). I know I could just build a new wall in front of the current wall but then I'd lose about 4 1/2 inches of precious interior space.

I THINK I could use some sort of furring strips to build out the face of the current wall but I'm not sure if that is the best solution. I also think I would want to build the face out past the face of the beam so that I could run electrical down inside the wall (IOW, don't make the wall flush with the beam but proud maybe an inch so there is a gap in the drywall at the top for wiring).

Does that make sense?

Will I be able to attach drywall to furring strips?

Also, there is a column just past the right end of the wall. I can't decide if I should extend the wall around this column and back or just turn the wall and the end of the existing studs and wrap the column separately. Any thoughts on that?

Thanks for any insight.


r/DIY • • 1d ago

help How to secure custom bespoke wardrobe to the wall ?

2 Upvotes

Hi all,

I’m currently assembling a custom 3-bay wardrobe (total width ~2448mm, height 2360mm, depth 600mm) made entirely of 18mm panels, including solid 18mm back panels. Each bay is built in two parts: a ~368mm drawer base unit on the bottom, with a ~1992mm tall wardrobe carcass sitting on top (fastened together).

Two of the bays are already built, joined together, and standing in place. Because of the skirting board and uneven walls, there is roughly a 30mm void/gap between the back of the 18mm wardrobe back panel and the wall. There's also only about a 70mm gap between the top of the wardrobe and the ceiling, so I can't easily get behind or over the top of it without dragging the whole thing forward.

The wall behind it is dot-and-dab plasterboard over brick/block.

What’s the cleanest and safest way to anchor this to the wall from inside the cabinets without bowing the 18mm back panels or dropping fixings down into that 30mm void? Would extra-long Corefix fixings work straight through the back panel, or is there a better trick for bridging that gap?

Thanks in advance!


r/DIY • • 1d ago

help Suggestions on how to make a art piece with billiard balls and a triangle rack?

0 Upvotes

My girlfriend’s cousin is having their engagement party soon and the couple loves to play pool together. We had an idea to make an art piece with a triangle rack and billiard balls with the numbers of their anniversary date. Any ideas on how to attach the billiard balls to the rack? Thinking of having the balls in the lower right corner and the bracket at the top point of the triangle.

Anything helps, thanks!


r/DIY • • 13h ago

help Does anyone actually keep track of how much they've saved doing DIY?

0 Upvotes

Just something I was wondering about today.

Over the years I've done a lot of DIY repairs and projects, both around the house and on vehicles, and it got me thinking about how much money I've actually saved by doing the work myself.

I've never really tracked it. Once the job is done, I move on to the next thing.

Do any of you keep records of your projects, receipts, photos, costs, notes, etc., or do you just finish the project and forget about it?

I was thinking it might be interesting to have a way to look back through everything you've fixed or built over the years and see what you've accomplished.

Curious what everyone here does now. Spreadsheet? Notebook? App? Or nothing at all?


r/DIY • • 1d ago

MOES CO and natural gas detectors

6 Upvotes

So I've installed two separate CO and natural gas detectors and they have never gone off. Both certified units. I originally had a MOES plug-in detector that kept giving off yellow alarms for natural gas and once a red alarm for CO. It's only supposed to red alarm when CO is at 100, but it did at 10. The yellow alarms were shown under the under the natural gas reading section. When they'd go off, if I ventilated, the alarms stopped. I had the gas company come out twice and they found no leaks or gas in the air (though I had been ventilating for over 30 minutes by the time they arrived).

The newer and better alarms have never gone off. I still have the MOES plugged in and it still gives readings sometimes. Should I just assume it's faulty since the two dedicated and better alarms have never gone off?


r/DIY • • 2d ago

help DIY Gut Kitchen Reno - Do I need permits/inspections? (MA)

33 Upvotes

Recently bought my first home-an old home in eastern MA and been DIYing a bunch. We are tackling a full kitchen renovation in December - just ordered the cabinets and appliances. Gonna be down to the studs and moving some plumbing around.

CONTEXT:
I’m having my uncle (experienced general contractor in NH), and other uncle (retired electrician in MA) help me out with the entire renovation start to finish so I’m not worried about doing things wrong. They are good at what they do just not currently licensed in MA.

What are the big risks/consequences of not pulling permits/getting inspections at different points?


r/DIY • • 2d ago

Twin Day Bed to Full

10 Upvotes

Has anybody tried extending their twin day bed into a full size before? I’m trying to think of ways to make my twin day bed a little bigger without having to get rid of it as it has some sentimental value. I know I would have to make a platform basically to extend it, but I still need to formulate how to do it that would provide sufficient support for weight and steadiness. And also make it not so ugly. Any input would be appreciated!


r/DIY • • 2d ago

help Drill bit broke off in screw trying to remove it from tub's overflow plate

19 Upvotes

This all started out with me trying to get my overflow plate off so I could clear a clog. (Thankfully, the tub now drains and I know how to snake it now, hurray)
However, what was supposed to be a simple fix turned into an absolute nightmare.

I used a reverse drill bit to remove the left screw but it broke off inside the right one.
The head of the screw came off and then when I took locking pliers to the body it sheered off at the plate. So now I'm stuck with the bit still in there (I don't think its too deep in there but unsure).
You can see my attempts to drill around the bit haven't been going too hot either.

Any suggestions for removal? I'm at a loss and beyond frustrated.

*EDIT*
I ended up finding a way to get to it from behind and got it out by screwing it the rest of the way in from behind with locking pliers.