r/Tile • • 18h ago

Homeowner - Advice about my Contractor Bad install?

Thumbnail
gallery
27 Upvotes

Have no idea what to think of the installation but we are very worried it is just sloppy and wonder if it can be fixed before the job is completed.


r/Tile • • 19h ago

General Discussion Rate our tile work

Thumbnail
gallery
18 Upvotes

My best friend and I tiled my kitchen backsplash. How did we do?

Please note anything we should have done differently.

Thanks!


r/Tile • • 3h ago

Homeowner - Advice about my Contractor Unfamiliar with tile work and need a critique/advice please

Thumbnail
gallery
6 Upvotes

Im having a new shower put in and I had some concerns about chips on the edge of the tiles and some grout lines. Im winding if this ia normal or I'm being too critical. Any advice or help would be appreciated. It seem almost everywhere they cut tile, that edge is jagged. Thanks in advance!


r/Tile • • 3h ago

Professional - Looking for Advice Tiled shower ceiling

Post image
4 Upvotes

A) can this ceiling carry the weight? It's 1/2" green board with red membrane, screwed into 16 center framing

B) what thin set, can regular thin set be used or do I need an upgraded hold

C) bracing jdeads without buying the legit tile supports


r/Tile • • 5h ago

DIY - Looking for Advice How to install marble threshold?

Post image
4 Upvotes

First time tile install. How do I install a marble threshold here? Should I put down small tiles in the gap to make it all level? Raise the threshold with wood or some other material? Cut the tile so the whole threshold sits on the underlayment?


r/Tile • • 20h ago

Professional - Looking for Advice Miter Improvement

Thumbnail
gallery
4 Upvotes

What can I do to improve my miter joints?


r/Tile • • 16h ago

Professional - Looking for Advice 11th hour cinder block shower bench

Thumbnail
gallery
3 Upvotes

TX client bought a new build 6? 7? years ago, lately noticed bad grout & funk smells in primary shower. He's undertaking the demo (I'm on another bathroom). The story: the requested 18×18" bench wasn't>>they told their builder to please do that before move-in>>sub built a bench>>nope, not 18",>>then added onto the "new" bench.

AI says: "Adding a shower bench to an existing finished shower is a complex retrofit that requires breaching the existing waterproofing and tile to ensure structural integrity and prevent leaks. The most reliable method involves carefully removing tiles in the designated area to access the wall studs, allowing for secure anchoring and proper integration of a new waterproof membrane."

I think I can do this; I've done ~40 showers with custom pans, benches, niches, etc. Anyone out there ever bump into something like this and have success reusing/folding up the liner onto a new framed bench or was it a complete re-pan?


r/Tile • • 3h ago

DIY - Looking for Advice Stand-Up Shower Repair Feedback

Thumbnail
gallery
2 Upvotes

Our shower is about 4.5 years old, and I'm looking for some feedback on a few things as I was hoping to do some DIY to save some money, but I wanted to see if there appears to be more work involved than I am aware of. 

I don't know much about tile or grout repairs, so I'm hesitant to start getting estimates without understanding what truly needs to be done. I don't want to pay to have all the grout and caulk replaced if only certain areas need repairs.

My main questions:

  1. Based on the condition of my shower in the pictures, do you think the cracked or deteriorating grout/caulk could be repaired individually, or whether all the grout and caulking need to be redone?
  2. Some of the grout lines look like they aren’t as full as they used to be. Can those areas be filled in, or does the existing grout need to be removed and replaced?
  3. The material in the corners where the walls and tile floor meet; is that the correct material for those areas?  It doesn't feel rubbery like I would expect silicone caulk to feel. It feels very dry and hard, and some of it comes off in chunks. Can you tell from the pictures what material was used?
  4. Along the edge of the shower seat, it looks like the porcelain tile is peeling or flaking. Any idea what's happening there and how it can be fixed?

 


r/Tile • • 19h ago

DIY - Looking for Advice What’s the trick?

Post image
2 Upvotes

What’s the trick to grouting this AmericanBiltrite Ultraceramic? Using their specified grout. Taken me almost two hours to get this far, trying to stay on top of the haze and follow their instructions. Seems like a never ending battle. Everything I’ve read seems to indicate leaving any haze behind will be a future nightmare but there’s just no way this should take so many wipes just to clean it up. The actual tile shower I did was much much easier to grout.

Just a stupid homeowner losing his mind here.


r/Tile • • 20h ago

Homeowner - Advice about my Contractor Should water sit under shower tiles?

Thumbnail
gallery
2 Upvotes

As many pictures of the before and after that I could find. The contractor insists that water sits beneath all shower tiles and if I had chosen a porcelain it wouldn't be a problem, but because I chose a marble, it is obvious. Hence my tile choice is the issue, not the installation.

The wet spots moved around when the shower was being used 1x/week. When used daily it never seems to dry. All photos at least 12 hours post use.


r/Tile • • 21h ago

Tools or Materials First time homeowner

Thumbnail
gallery
2 Upvotes

I wanted to hear advice from you guys. First time home owner here, and I know I need to re-grout the tile. I don’t want to damage the 1950s tile so if anybody has advice on what tools to use that would be awesome.
Maroon tile is in the bathroom and the blue tile is in the kitchen if that helps. I feel like the lines are pretty thin as well.


r/Tile • • 1h ago

DIY - Looking for Advice Name of tile that is a bit rubbery to the touch? Does anyone know?

1 Upvotes

A family member bought an old jugend villa which had this amazing deep red tile in the entrance hallway that felt a bit rubbery to the touch. Apparently it was a typical French tile. Does it have a particular name? Where can I buy it?


r/Tile • • 4h ago

DIY - Looking for Advice Looking to replace floor tile now and shower tile in 3-5 years, does this look horrible?

Thumbnail
gallery
1 Upvotes

Note - this is the guest bathroom and we are redoing the master bathroom. Master has similar vanity and the same shower tile so I think this works better as an example.

We’re doing a partial renovation of the master bathroom but not touching the shower tile. The rest of the house is mostly white and grey, not much tan. I was hoping the marbling in the hex tile would help blend the colors a little but I’m not so sure. Do we think these could work or should I continue my search?


r/Tile • • 6h ago

DIY - Looking for Advice Corner of one tile has come loose

1 Upvotes

Pretty straight forward, one of my 12x12 tiles has a corner that clicks when stepped on (it's in a bathroom, and it's the tile that butts to the tub, it's a whole uncut tile). The floor is 25 years old but in good shape. I assume the floor shifted under it. I have extra tile but I don't want to pull the tile bc then I'd need to regrout, and the grout is pretty well aged. Any tips on how we can stabilize this? It's more of an annoyance than anything.


r/Tile • • 7h ago

DIY - Looking for Advice General Guidance - NYC

Thumbnail
gallery
1 Upvotes

Hello all. Pictured here are the entrance steps (on grade) to my house in NYC. The grout/mortar between the tile/brick has been degrading over time, and I think the extreme cold last winter with the melted (de-iced) snow and general dampness got underneath the tile and broke everything apart from the freeze-thaw. I know it’s cold weather already, but I’d like to try and fix it myself this year before a professional replaces everything next year. When I lifted a few of the tiles, I expected some sort of thin-set material but it tended to look like hardened mortar in spots and broken down, sandy mortar in other spots. All to say, the I think the base needs to be redone. There are a number of steps to do, so I was wondering if the community could help with the following general guidance.

  1. I plan to start at the top step and work down. They are all on grade. Does that make sense?
  2. I plan to lift each brick, clean and soak in water, and do the same beneath the tile. The brick is 2” thick and the tile about 3/8” (meaning they are set at different grades). I would bring the base down down to bottom of brick, and reset the brick using quikcrete mortar mix on the bottom and sides. I’d let that set up and then put the removed material back up to -1” from top of tile and tamp down.
  3. from there, I’d mix up more mortar mix to -3/8” elevation and reset the tiles (soaking and buttering the bottom of each as well; however this tile doesn’t seem very porous so I’m not sure how to properly bond it).
  4. repeat for each step
  5. next day, I’d grout the tile joints with kerapoxy CQ and clean up whatever squishes out.
  6. no foot traffic for 24h after setting tile.

Does this make sense or am I way off? Again, this is an interim solution until I can get a pro to do it.


r/Tile • • 7h ago

Tools or Materials Vinegar ruined my shower bench

Thumbnail
gallery
1 Upvotes

I haven't even used my new shower yet and the engineered stone bench is ruined. Contractor told me to wipe down the floor tile with a vinegar and water solution to remove the haze after one day. I must have splashed some vinegar on my bench and it now has white spots. Google ai says that the vinegar caused etching. Wtf kind of material is so easily damaged by vinegar?

How do I fix? It's not really the contractors fault, tho he did tell me to use vinegar. I might have used vinegar myself in the future, so ??? Also, I've already paid him in full, so he's not likely to care.


r/Tile • • 15h ago

General Discussion Converting this tub into a shower — how would you waterproof around this window?

Post image
1 Upvotes

We're planning to add a shower to this tub area, but I'm trying to figure out the best way to waterproof and tile around the existing window.

The house has a brick exterior, so we'd really prefer to keep the existing window opening and size rather than modify the brickwork.

I'm particularly concerned about waterproofing the sill, jambs, and the transition between the tile and window frame.

How would you guys approach this? Can it be done reliably with the existing window, or would we need to replace the window while keeping the same opening?

I'd appreciate any advice from tile setters who've dealt with similar setups.


r/Tile • • 17h ago

Tools or Materials Looking for this exact tile to replace a few cracked ones. Tile is discontinued.

Post image
1 Upvotes

I have searched local resale/outlet stores in my area, Facebook marketplace, Ebay, the list goes on. I can't find this exact 18x18" in the Crema color. Please help!


r/Tile • • 17h ago

Homeowner - Advice about my Contractor Need help! Poor workmanship or waterproofing cause?

1 Upvotes

Hi newly built brick and mortar house owner here, my bathroom wall tiles are hollow sounding and started to see some cracks after only 6 months. The video above shows one tile that was removed for inspection. The contactor blames the waterproofing (Sika 107) not working well with adhesive ( Flinken C2). The empty voids look to me like it was not pressed and wiggled enough. What do you guys think? What should I do?

Also, My kitchen does not have waterproofing but every wall tile is solid sounding. My bathroom floors have same water proofing as bathroom walls but no hollow sounds. All done by same contractor with same adhesive Flinken C2.


r/Tile • • 19h ago

DIY - Looking for Advice Supporting studs behind cement board—I think I need to redo this?

Post image
1 Upvotes

I hired someone to add this wall. He used 1/2" cement board. But among other things, there's 23" between the two leftmost vertical studs. It's missing support at the tub lip and seam. And there's no 1/8" gap at the seam.

Another tiler I talked to said this would be fine. But I can see it flex a bit above the tub when I press from the back.

I wonder if I need to take it all off and add one more vertical stud in the middle and then horizontal supports at the tub lip and seam? Anything else?

If I do that, for the horizontal pieces, can I put a 2x4 flat, with the wide part facing out? I know it might flex a bit that way, but I'm not sure how else I'll fit it in front of the pipes.

And I can't hang cement board by myself, so I think I'll have to buy a bunch of Kerdi or GoBoard to replace what's there.

Thanks for thoughts!

P.S. I know it's a mess how the tub surround is farther out than the drywall. That's a whole other sob story.


r/Tile • • 19h ago

Homeowner - Advice about my Contractor Laundry Room Tile Added Cost

Post image
1 Upvotes

What would be a reasonable cost to tile this laundry space accounting for the increased waste and labor of doing a diamond checkerboard pattern? Standard tile and labor is included in the purchase price of our new build for the laundry room. Wanted to use square 12x12 tile in this laundry room in a checkerboard pattern (diamond orientation). The tile we chose is similar cost (10.29/sq ft) to the builder selection center tile.

New build in the Midwest (Ohio/Michigan/Indiana area). Know the builder usually charges a premium but the quote seems too high despite that. Am I just underestimating the labor and overage involved to make the diamond checkerboard? Quote was just over $1600


r/Tile • • 19h ago

DIY - Looking for Advice What should I do, here?

Post image
1 Upvotes

Hi All,

This is the shower floor in my 1960's house. It's original from when the home was built in 1966. The tiles were all starting to come up, so I removed them. Unfortunately, there's a tiny difference in the way this mosaic tile was spaced back then versus now, and any new samples don't line up correctly with that little bump-out around the shower drain.

I would love to do another mosaic, but I can't seem to find anything that would lay correctly around the drain. Any thoughts on how to manage this?

Another option would be to do an epoxy floor and just use a solid color, but I'd miss the mosaic look.

Thanks for any suggestions.


r/Tile • • 19h ago

DIY - Looking for Advice Backer board to linoleum on subfloor?

Post image
1 Upvotes

I am prepping my floor for tile. For whatever reason this old linoleum (no underlayment) literally just the paper material is glued straight to the subfloor. The plywood that I am tearing up was stapled to the subfloor. Would it be wrong to tear out the plywood, hammer the staples and lay backboard directly on top of the linoleum?


r/Tile • • 20h ago

DIY - Looking for Advice Hairline crack on bathroom tile near shower - concern?

Thumbnail
gallery
1 Upvotes

Hey everyone! I moved into this new build 5 years ago and a few years ago I noticed this hairline crack right beside my stand up shower. It sort of seems to be getting longer but doesn’t seem as deep? More looks like a scratch as it gets longer.

Is this a cause for concern? Should I look at having it replaced? Is there anyway to fix it without replacing?

I am in a condo building, not a home.

Thank you!